VERDER CARBOLITE GERO CFM 14/2 Handbuch

Installation, Operation and Maintenance Instructions

1400°C Combustion Tube Furnace - CFM Model:14/2

No Controller

CFM 14/2 + No Controller

MEN-CFM1402-005_NOCTRL (18-10-2021)

Contents

This manual is for guidance on the use of the Carbolite Gero product specified on the

front cover. This manual should be read thoroughly before unpacking and using the

furnace or oven. The model details and serial number are shown on the back of this

manual. Use the product for the purpose for which it is intended.

1.0 Symbols and Warnings 4

1.1 Switches and Lights 4

1.2 General Warnings 4

2.0 Installation 6

2.1 Unpacking and Handling 6

2.2 Siting and Setting Up 6

2.3 Heating Elements 7

2.4 Electrical Connections 8

3.0 Temperature Controller 10

4.0 Operation 11

4.1 Operating Cycle 11

4.2 General Operating Advice 11

4.3 Tube Life 12

4.4 Operator Safety 12

4.5 Pressure 13

5.0 Maintenance 14

5.1 General Maintenance 14

5.2 Maintenance Schedule 14

5.2.1 Cleaning 16

5.3 Calibration 16

5.4 After-Sales Service 16

5.5 Recommended Spare Parts and Spare Parts Kit 16

5.6 Power Adjustment 16

5.7 Element Ageing 17

6.0 Repairs and Replacements 18

6.1 Safety Warning - Disconnection from Power Supply 18

6.2 Safety Warning - Refractory Fibre Insulation 18

6.3 Temperature Controller Replacement 18

6.4 Solid-State Relay Replacement 19

6.5 Thermocouple Replacement 19

6.6 Element Fitting and Replacement - 1400 °C Models 20

6.7 Fuse Replacement 21

7.0 Fault Analysis 22

A. Furnace Does Not Heat Up 22

B. Product Overheats 23

8.0 Wiring Diagrams 24

8.1 WA-11-10 24

8.2 WA-11-11 25

8.3 WA-11-30 26

9.0 Fuses and Power Settings 27

9.1 Fuses 27

9.2 Power Settings 27

User Power Setting Adjustments 28

10.0 Specifications 29

10.1 Environment 29

1.0 Symbols and Warnings

1.1 Switches and Lights

Instrument switch: when the instrument switch is operated the

temperature control circuit is energised.

Heat light: the adjacent light glows or flashes to indicate that

power is being supplied to the elements.

Heat switch: the switch disconnects power to the heating

elements; unless this switch is OFF there is a danger of electric

shock when inserting objects into the product.

1.2 General Warnings

DANGER – Electric shock. Read any warning printed next to this

symbol.

WARNING: Risk of fatal injury.

DANGER – Hot surface. Read any warning printed next to this

symbol.

WARNING: All surfaces of a product may be hot.

DANGER – Read any warning printed next to this symbol.

Caution – Double Pole/Neutral Fusing

2.0 Installation

2.1 Unpacking and Handling

When unpacking or moving the product always lift it by its base or by both ends of the

main body. Never lift it by its work tube or the surrounding insulation. Use two or more

people to carry the product and control box. Remove any packing material from inside

the product before use.

If an optional or special stand is separately supplied, assemble the product on to it.

Some models may be supplied for customer mounting and may require customer

preparation of mounting components before installation.

NOTE: This product contains Refractory Ceramic Fibre (also known

as Alumino Silicate Wool - ASW). For precautions and advice on

handling this material see section 6.2.

2.2 Siting and Setting Up

Place the product on a level surface in a well ventilated area.

Site away from other sources of heat and on a non-flammable surface that is resistant

to accidental spillage or hot materials.

The surface on which the equipment is mounted should be stable and not subject to

movement or vibrations.

The height of the mounting surface is important to avoid operator strain when loading

and unloading samples.

Unless otherwise stated elsewhere in this manual, ensure that there is at least 150

mm of free space around the back and sides of the product. Clear space is required

above the product to dissipate heat.

Work tubes:

It is recommended that the work tube has either insulation plugs or

radiation shields fitted to minimise heat loss from both ends of the work

tube. If the work tube has open ends, a significant amount of energy

could be radiated from the ends of the work tube. Adjacent surfaces

should always be made from a non-flammable material.

Ensure that the ends of the work tube are positioned at least 500 mm

away from any adjacent surface so that any energy radiated cannot heat

an adjacent surface to a dangerous temperature.

Ensure that the product is placed in such a way that it can be quickly switched off or

disconnected from the electrical supply.

The product is typically used for sulphur and chlorine test in accordance with BS1016

parts 6 & 7, ASTM D 3177-75; ISO 351 & 609.

Please refer to the appropriate documentation.

This manual only gives general guidance common to tube products.

Fit any work tube(s) ordered into place. If a metal work tube is being used in the

product, ensure that it is earthed and that it is mounted so as not to touch the products

ceramic tube or insulation.

Under no circumstances should any objects be placed on top of the

product. Always ensure that any vents on the top of the product are clear

of any obstruction. Always ensure all cooling vents and cooling fans (if

fitted) are clear of any obstruction.

2.3 Heating Elements

The silicon carbide elements are VERY FRAGILE and are packed separately. Fit them

accordingly to the instructions in section 6.0 for element fitting and replacement

instructions.

2.4 Electrical Connections

Connection by a qualified electrician is recommended.

This product requires a single-phase A.C. supply with earth (ground), which may be

Live to Neutral non-reversible (polarised), Live to Neutral reversible (non-polarised), or

Live to Live.

Check the product rating label before connection. The supply voltage should agree with

the voltage on the label and the supply capacity should be sufficient for the current on

the label.

The supply should be fused at the next size equal to, or higher than the current on the

label. This manual contains a table of the most common fuse ratings.

When the mains cable is factory fitted, internal fuses are also fitted. It is essential that

the operator ensures that the product is correctly fused.

Products with a factory fitted supply cable are designed to be wired directly to an

isolator or fitted with a line plug.

Products without a factory fitted supply cable require a permanent connection to a

fused and isolated supply. The product's electrical access panel should be temporarily

removed, and connections made to the internal terminals.

When connecting the product to the power supply, the plug or isolating switch should

be accessible, easy to remove, and within reach of the operator.

The supply MUST incorporate an earth (ground).

Supply Terminal Label Cable Colour

Supply Types

Live - Neutral Reversible or Live-

Live

1-phase L1 Brown to live

to either power

conductor

(For USA 200-240V,

connect L1)

N / L2 Blue to neutral

to the other power

conductor

(For USA 200-240V,

connect L2)

PE Green/ Yellow to earth

(ground) to earth (ground)

Electrical Connection Details:

Technical Notes

This model has an electronically controlled power limit. Do not attempt to calculate the

Amps from the Wattage. High break capacity fuses should be used. Avoid fast-blow

fuses and magnetic trip circuit breakers - consult Carbolite Gero if in doubt.

3.0 Temperature Controller

If this product is fitted with a temperature controller, instructions are provided

separately.

Andere Handbücher für CARBOLITE GERO CFM 14/2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VERDER Ofen Handbücher

VERDER

VERDER CARBOLITE GERO HTF 18/27 Handbuch

VERDER

VERDER Carbolite HTF 17 Leitfaden

VERDER

VERDER CARBOLITE GERO BLF 18/8 Handbuch

VERDER

VERDER CARBOLITE GERO CFM 14/2 AUX Handbuch

VERDER

VERDER Carbolite Gero CWF 13/23 Handbuch

VERDER

VERDER Carbolite Gero AAF 12/18 Handbuch

VERDER

VERDER CARBOLITE GERO 2416 Series Handbuch

VERDER

VERDER CARBOLITE GERO EHA 12/300B Handbuch

VERDER

VERDER CARBOLITE GERO MTF 12/25 Series Handbuch

VERDER

VERDER CARBOLITE GERO CWF 12/13 Handbuch

VERDER

VERDER Carbolite Gero RHF 16/15 Handbuch

VERDER

VERDER Carbolite Gero EVT 12/600B Handbuch

VERDER

VERDER HZS 12/900 Handbuch

VERDER

VERDER TVS 12/900 Handbuch

VERDER

VERDER CARBOLITE GERO GPC 12/200 Handbuch

VERDER

VERDER CARBOLITE GERO HST 12/450 Handbuch

VERDER

VERDER CARBOLITE GERO EHA 12/450B Handbuch

VERDER

VERDER CARBOLITE GERO CWF 13/5 Handbuch

VERDER

VERDER CARBOLITE GERO CRF/1 Handbuch

VERDER

VERDER TZF 12/65/550 Handbuch

VERDER

VERDER Carbolite Gero EHC 12/450B Handbuch

VERDER

VERDER Carbolite Gero EVC 12/600B Handbuch

VERDER

VERDER CARBOLITE GERO E Series Handbuch

VERDER

VERDER CARBOLITE GERO STF 15/180 Handbuch

Beliebte Ofen Handbücher anderer Marken

Armstrong

Armstrong EG7H SERIES Bedienungsanleitung

Payne

Payne PG92ESA Leitfaden

SUPREME

SUPREME FEM10-M2301CM-A Montageanleitung

Ingersoll-Rand

Ingersoll-Rand S9V2B080D4VSAC/D Montageanleitung

Johnson Controls

Johnson Controls TM9T Leitfaden

Fluke

Fluke 9118A Bedienungsanleitung

Lennox

Lennox EL195UHE Elite Series Installations- und Betriebshandbuch

Intertherm

Intertherm M7RL Series Bedienungsanleitung

HDG

HDG Pelletmaster 15 Bedienungsanleitung

Pinnacle

Pinnacle Aero Bella AB-716C-QH Handbuch

Nortek

Nortek MG2S Series Bedienungsanleitung

Goodman

Goodman GMV9 Handbuch

SUPREME

SUPREME SUP10-M2301C Montageanleitung

Dettson

Dettson AMT400B34-SM1PMA Montageanleitung

Evcon

Evcon DGD 60 MBH Bedienungsanleitung

Trane

Trane S8B1A026M2PSAB Montageanleitung

Hart Sceintific

Hart Sceintific 9113 Bedienungsanleitung

Whirlpool

Whirlpool Gold WGGE45 Bedienungsanleitung