Vermont Castings SB100 Bedienungsanleitung

VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

Installation and service of this replace should be

performed by qualied personnel. Vermont Cast-

ings Group recommends NFI certied profession-

als, or technicians supervised by an

NFI certied professional.

WOODBURNING FIREPLACE

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overre and generate

poisonous gases (i.e. carbon monoxide).

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ammable

materials.

• Keep clothing, furniture, draperies and other ammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

SB100

SB100HB

NOTICE: DO NOT discard this manual!

• DO NOT store or use gasoline or other am-

mable vapors and liquids in the vicinity of this

or any other appliance.

• DO NOT overre. Overring will void your

warranty.

• Comply with all minimum clearances to com-

bustibles as specied. Failure to comply may

cause house re.

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property

damage, personal injury, or death.

This replace uses SL1100 Series Chimney

2” CLEARANCE TO COMBUSTIBLES AND BUILDING INSULATION FROM CHIMNEY REQUIRED.

2VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Indicates practices which may cause damage to the replace or to property.

Table of Contents

1 Product Specic & Important Safety Information

A. Fireplace Certication 4

B. Non-Combustible Materials 4

C. Combustible Materials 4

2 Getting Started

A. Typical Fireplace System 5

B. Design and Installation Considerations 6

1. Selecting Fireplace Locations 6

2. Locating Fireplace & Chimney 7

C. Tools and Supplies Needed 8

D. Inspect Fireplace and Components 8

E. Fireplace System Requirements 8

3 Framing and Clearances

A. Fireplace Dimensions 9

B. Clearances 10

Minimum Clearances to Combustibles 10

C. Construct the Chase 11

D. Unpack the Refractory & Fireplace 12

E. Frame the Fireplace 13

F. Secure and Level the Fireplace 13

G. Protective Metal Hearth Strips 14

H. Outside Air Kit 15

4 Chimney and Termination Requirements

A. Chimney Requirements 17

B. Offsets/Returns 18

C. Termination Requirements 19

5 Chimney Installation

A. Typical Chimney System 20

B. Assemble Chimney Sections 21

C. Install Chimney Air Kit (optional) 21

D. Secure Offset/Return 22

E. Install Ceiling Firestops 22

F. Install Attic Insulation Shield 23

G. Roof Penetration 24

H. Install Chase/Chase Top 24

I. Termination Cap Requirements 25

J. Install Termination Cap 25

6 Shrouds

A. Radiation Shield 27

B. Field Constructed Shrouds 27

1. Open Top Shroud 27

2. Mailbox Style Shroud 28

3. Roofed Style Shroud 28

7 Finishing

A. Finishing Material 29

B. Hearth Extension, Building and Finishing 30

1. Fireplace Installed Flush on the Floor

and Hearth Extension Raised to Bottom

of Firebox Opening 31

2. Raised Hearth Extension and Raised Fireplace 32

3. Fireplace Opening and Hearth Extension Flush

with the Floor 33

C. Non-Combustible Sealant Material 33

D. Mantel and Wall Projections 34

E. Sidewalls/Surrounds 35

8 Fireplace Setup

A. Install Refractory 36

B. Gas Log/Lighter Provision 38

C. Wood Burning Inserts 38

9 Reference Materials

A. Chimney Components 39

B. Optional Components 42

VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

Customer:

Lot/Address

Model (circle one): SB100

YES IF NO, WHY?

Protective hearth strips installed per manual requirements. (Pg. 14)

Outside air kit installed. (Pg 15)

Attic insulation shield installed.

Shroud is installed properly per instructions.

Chimney Section 4 & 5 (Pg. 17)

Fireplace Install

Shrouds Section 6 (Pg. 27)

Fi i hi

S ti 7 (P 29)

WARNING! Risk of Fire or Explosion! Failure to install fireplace acording to these instructions can lead to a fire or

explosion.

Verified that the chase is insulated and sealed. (Pg. 11)

Verified clearances to combustibles. (Pg. 10)

Fireplace is leveled and secured. (Pg. 13)

Hearth extension size/height decided. (Pg. 30)

Chimney configuration complies with diagrams.

Chimney installed, locked and secured in place with proper clearance.

Chimney air kit installed.

Firestops installed.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation

manual.

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Roof flashing installed.

Termination installed.

Hearth extension installed per manual requirements.

Comments communicated to party responsible

4013-305 • Rev A• 2-19-15

Vermont Castings Group recommends the following:

Finishing Section 7 (Pg. 29)

Fireplace Setup Section 8 (Pg. 36)

Verified all clearances meet installation manual requirements.

Mantels and wall projections comply with installation manual requirements.

All packaging and protective materials removed.

Optional doors properly installed.

Molded brick panels installed correctly.

Grate is properly installed.

Firescreen installed properly.

__________________________ by ______________________on _________

(Builder/Gen. Contractor) (Installer) (Date)

Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, etc.) and corrective action needed:

Manual bag and all of its contents are removed from the fireplace and given to the party

responsible for use and operation.

• That this checklist remain visible at all times on the fireplace until the installation is complete.

• Photographing the installation and copying this checklist for your file.

Combustible materials not installed in non-combustible areas.

4VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

WARNING! Risk of Fire! Vermont Castings Group dis-

claims any responsibility for, and the warranty and agency

listing will be voided by the following actions.

DO NOT:

• installoroperatedamagedreplace

• modifyreplace

• install other than as instructed by Vermont Castings

Group

• operate the fireplace without fully assembling all

components

• overre

• installanycomponentnotapprovedbyVermontCastings

Group

• installpartsorcomponentsnotListedorapproved

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. For

assistance or additional information, consult a qualied

installer, service agency or your dealer.

B. Non-Combustible Materials

• Materials which will not ignite and burn, composed of

any combination of the following:

- Steel - Iron

- Brick - Tile

- Concrete - Slate

- Glass - Plasters

• Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace at 750° C

C. Combustible Materials

• Materials made of or surfaced with any of the following

materials:

- Wood - Compressed paper

- Plant bers - Plastic

- Plywood/OSB - Sheet rock (drywall)

• Any material that can ignite and burn; ame proofed or

not, plastered or un-plastered

1 Product Specic & Important Safety Information

A. Fireplace Certication

This replace may be installed in sleeping rooms. This

replace is not approved for manufactured housing. If in-

stalled with a gas log set, provisions for the National Fuel

Gas Code must be met.

This replace has been tested and listed for use with

the optional components specied in this manual. These

optional components may be purchased separately and

installed at a later date. An outside air kit, gas insert, gas

log set or gas log-lighter should be installed at the time of

replace installation.

This replace system has been tested and listed in accor-

dance with UL 127 standards by Underwriters Laborato-

ries Inc. for installation and operation in the United States.

VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

2 Getting Started

A. Typical Fireplace System

Figure 2.1 Typical Fireplace System

)

))

)

Non-combustible

roof flashing maintains

minimum clearance

around chimney

Additional lateral

support for chimney

above roof (or enclosed

in chase) if needed

Ceiling firestop

on floor of attic

Support straps

on rafter support

chimney

Termination cap

Chimney penetrates roof

preferably without affecting

roof rafters

Offset & Return (with hanger straps)

Framing headed off

in ceiling joists

Enclosed space above

and around fireplace

Mantel and surround

Decorative facing

and trim

Hearth extension

Factory-built fireplace

Protective metal

hearth strip(s)

Outside

combustion air

Combustible framing/header

on top of V-shaped standoffs

Chimney system

Attic insulation shield

must be used here to keep

insulation away from chimney

if attic is insulated

Storm Collar

6VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

Figure 2.2 Fireplace Locations

NOTICE:

• Illustrationsandphotosreecttypicalinstallationsand

are FORDESIGNPURPOSESONLY.

• Illustrations/diagramsarenotdrawntoscale.

• Actualinstallation/appearancemayvaryduetoindividual

design preference.

• VermontCastingsGroupreservestherighttoalterits

products.

NOTICE: In addition to these framing dimensions, also

reference the following section:

• Clearances (Section 3).

NOTICE:

Aminimum1-1/2in.airclearanceatthebackand

aminimum1-1/2in.airclearancetothesidesof

thereplaceassemblymustbemaintained.

Chimney sections at any level require

a 2 in. minimum air space clearance

between the framing and chimney sec-

tions.

B. Design and Installation Considerations

NOTICE: Checkbuildingcodespriortoinstallation.

• Installation MUST comply with local, regional, state and

national codes and regulations.

• Consult insurance carrier, local building inspector, re

ofcials or authorities having jurisdiction over restrictions,

installation inspection and permits.

• Before installing, determine the following:

- Where the replace is to be installed.

- The vent system conguration to be used.

- Gas supply piping.

- Electrical wiring.

- Framing and nishing details.

- Whether optional accessories - devices such as a

fan, wall switch or remote control - are desired.

1. Selecting Fireplace Locations

This replace may be used as a room divider, installed

along a wall, across a corner or used in an exterior chase.

See Figure 2.2.

Locating the replace in a basement should be avoided.

Locating near frequently opened doors, central heat

outlets or returns, or other locations of considerable air

movement can affect the performance.

Note: 1-1/2 in. (38 mm) min.

distance from sides & back

of fireplace to combustible

materials. 1/2 in. (13 mm)

min. at nailing flanges.

30-1/2 in.

(775 mm)

77-5/8 in.*

(1972 mm)

1/2 in. (13 mm)

all configurations

In an exterior chase

or projecting into a

garage

Across a

corner

Along a wall

30-1/2 in.

(775 mm)

24 in.

(610 mm)

77-5/8 in.

(1972 mm)

As a room

divider

30-1/2 in.

(775 mm)

48 in.

(1219 mm)

77-5/8 in.

(1972 mm)

52-1/2 in.

(1334 mm)

61-5/8 in.

(1565 mm)

104-7/8in.

(2664 mm)

24-3/8 in.

(619 mm)

74-1/4 in.

(1886 mm)

24 in.

(610 mm)

*8 in. (203 mm) extra space

included (both sides) for outside

air connection. If outside air duct

has no bend, this dimension

may be reduced as long as

minimum clearances are met.

Consideration should be given to these factors before

deciding on a location.

VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

2. Locating Fireplace & Chimney

Location of the replace and chimney will affect perfor-

mance.

• Install within the warm airspace enclosed by the building

envelope. This helps to produce more draft, especially

during lighting and die-down of the re.

• Installing the replace in a basement is not recommended.

• Penetrate the highest part of the roof. This minimizes

the effects of wind loading.

• Locate termination cap away from trees, adjacent

structures, uneven roof lines and other obstructions.

• Minimize the use of chimney offsets.

• Consider the replace location relative to oor and ceiling

and attic joists.

• Take into consideration the termination requirements in

Sections 4 and 5.

Marginal Location:

• Below peak

Location NOT recommended:

• Not the highest point of the roof

• Wind loading possible

Multi-level Roofs

Windward

Leeward

Recommended Location:

• Above peak

Recommended:

• Insulated exterior chase

in cooler climates

Recommended Location:

• Above peak

• Inside heated space

Location NOT recommended:

• Too close to tree

• Below adjacent structure

• Lower roof line

• Avoid outside wall

Marginal Location:

• Wind loading possible

Figure 2.3 Recommended Chimney Locations

• Install the outside air kit with the intake facing prevailing

winds during the heating season.

• Ensure adequate outdoor air for all combustion

appliances and exhaust equipment.

• Ensure furnace and air conditioning return vents are not

located in the immediate vicinity of the replace.

• Avoid installing the replace near doors, walkways or

small isolated spaces.

• Recessed lighting should be a “sealed can” design.

• Attic hatches weather stripped or sealed.

• Attic mounted duct work and air handler joints and seams

taped or sealed.

8VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

C. Tools and Supplies Needed

Before beginning the installation be sure the following

tools and building supplies are available:

Reciprocating saw Framing material

Pliers Non-combustible sealant

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits

Plumb line Safety glasses

Level Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws

Misc. screws and nails

D. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged

parts could impair safe operation. DO NOT install dam-

aged,incompleteorsubstitutecomponents.Keepre-

place dry.

• Remove replace and components from packaging and

inspect for damage.

• Vent system components and doors are shipped in

separate packages.

• Report to your dealer any parts damaged in shipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benet.

E. Fireplace System Requirements

The VCG replace system requirements consist of the

following:

• Fireplace

- Refractory (included with replace)

- Firescreen (included with replace)

- Grate (included with replace)

- Hearth Extension (required, sold separately)

• Outside Air System

- Air Inlet Hood (included with replace)

- Flex (required, sold separately)

• Chimney System

- Attic Insulation Shield (included with replace)

- Chimney termination cap (required, sold separately)

• Non-combustible nish material

VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

3 Framing and Clearances

A. Fireplace Dimensions

Figure 3.1 Fireplace Dimensions

60 5/8 in.

(1540 mm)

20 3/4 in.

(527 mm)

11 5/8 in.

(295 mm)

29 1/2 in.

(749 mm)

14 3/4 in.

[375 mm]

Gas

Knockout

9 7/8 in.

[251 mm]

19 in.

[483 mm]

10 1/2 in.

[267 mm]

Outside

Air

14 3/4 in.

[375 mm]

Gas

Knockout

9 7/8 in.

[251 mm]

19 in.

[483 mm]

10 1/2 in.

[267mm]

Outside

Air

50 in.

[1270 mm]

33 in.

[838 mm]

68 1/8 in.

[1730 mm]

(effective height)

8 3/4 in.

[222 mm]

70 1/2 in.

[1791 mm]

60 1/4 in.

[1530 mm]

54 3/8 in.

[1381 mm]

41 5/8 in.

(1057 mm)

10 VCG Biltmore Series • SB100 • 4013-303 Installers Manual • Rev A • 02/19/15

B. Clearances

WARNING! Risk of Fire!

You must comply with all minimum air space clearances

tocombustiblesasspeciedinFigure3.2.DO NOTpack

required air spaces with insulation or other materials.

Framing or nishing material used on the front of, or in

frontof,thereplacecloserthantheminimumslistedmust

be constucted entirely of non-combustible materials (i.e.,

steel studs, concrete board, etc.). Failure to comply may

causere.

Figure 3.2 Clearances to Combustible Materials

Minimum Clearances to Combustibles

WITHIN ENCLOSURE AREA

Fireplace to backwall 1-1/2 in. (38 mm)

Fireplace to sidewall 1-1/2 in. (38 mm)

Top standoffs to header 0 in. (0 mm)

Door opening to sidewall 24 in. (610 mm)

MANTEL

Mantel minimum height 20 in. (508 mm)

above opening

Maximum mantel depth 12 in. (305 mm)

0 in.

from floor

Attic

Insulation

Shield

Ceiling Firestop

(ceiling)

(roof)

(attic)

(ceiling)

2 in. min.

(51 mm)

2 in. min.

(51 mm)

2 in. min.

(51 mm)

2 in. min.

(51 mm)

2 in. min.

(51 mm)

2 in. min.

(51 mm)

Must have 2 in. (51 mm)

minimum clearance

to header

Ceiling Firestop Offset/Return with

hanger straps

Storm Collar

Roof Flashing

0 in. to level

of standoffs

1-1/2 in. (38mm) from

side of appliance

(except at nailing flanges

where it is 1/2 in. (13 mm)

1-1/2 in. (38mm) from

back of appliance

Andere Handbücher für SB100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vermont Castings Kamin im Innenbereich Handbücher

Vermont Castings

Vermont Castings VE1263 Montageanleitung

Vermont Castings

Vermont Castings DEF33 Montageanleitung

Vermont Castings

Vermont Castings DEF36S2 Bedienungsanleitung

Vermont Castings

Vermont Castings WDVST500 Handbuch

Vermont Castings

Vermont Castings Chateau DVT38S2IN Montageanleitung

Vermont Castings

Vermont Castings VLI31DVN Bedienungsanleitung

Vermont Castings

Vermont Castings DSR42 Bedienungsanleitung

Vermont Castings

Vermont Castings 380IDVNV Bedienungsanleitung

Vermont Castings

Vermont Castings Wood Fireplace Bedienungsanleitung

Vermont Castings

Vermont Castings VFC24C Handbuch

Vermont Castings

Vermont Castings DVR28IN Montageanleitung

Vermont Castings

Vermont Castings Indoor Gas Fireplace 33LDVT Bedienungsanleitung

Vermont Castings

Vermont Castings A18CFLRN/P Bedienungsanleitung

Vermont Castings

Vermont Castings VWDVP70NTSC Bedienungsanleitung

Vermont Castings

Vermont Castings 36CDVZRRN Montageanleitung

Vermont Castings

Vermont Castings Insert Studio LHEC20 Bedienungsanleitung

Vermont Castings

Vermont Castings Merrimack Montageanleitung

Vermont Castings

Vermont Castings MLDV500 Handbuch

Vermont Castings

Vermont Castings 500DVM Handbuch

Vermont Castings

Vermont Castings Montpelier Montageanleitung

Vermont Castings

Vermont Castings Savannah SSI30 Bedienungsanleitung

Vermont Castings

Vermont Castings VCEF26 Montageanleitung

Vermont Castings

Vermont Castings VWF18STN Bedienungsanleitung

Vermont Castings

Vermont Castings 2050 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch