Vermont Castings Intrepid 2 Bedienungsanleitung

Intrepid 2

Intrepid 3

Model Nos. V 10 / V10-3 NAT GAS

Model Nos. V12 / V12-3 L.P.G

DECORATIVE COAL EFFECT GAS

STOVE

USER INSTRUCTIONS

This appliance is only for use on Natural Gas (G20) at a supply

pressure of 20 mbar in GB / IE (Model No. V10/V10-3)

Propane G31 at a supply pressure of 37mbar in GB / IE (Model

No. V12/V12-3)

CONDITIONS OF INSTALLATION

It is the law that all gas appliances are installed only by a competent (e.g. CORGI

Registered) Installer, in accordance with the installation instructions and the Gas Safety

(Installation and Use) Regulations 1994 with the rules in force. Failure to install

appliances correctly could lead to prosecution. It is in your own interest and that of safety

to comply with the law.

The stove may be fitted below a combustible shelf providing that the shelf is at least

610mm above the top of the stove, the shelf must not extend in front of the stove. For a

combustible side surface a minimum distance of 305mm is required, combustible rear

surface 305mm and any rear surface 100mm.

No additional purpose made additional ventilation is normally required for this appliance in

G.B.

If the chimney or flue has been previously used by appliances burning fuels other than

gas, they must be swept prior to the installation of this stove.

NB. For appliances installed in Republic of Ireland, refer to Domestic Gas Installation

document for specific ventilation requirements.

The Model number of this appliance is V 10;V10-3;V12;V12-3 and it is manufactured by: -

The rating plate is located on the control panel on the underside of the appliance

VERMONT CASTINGS INC.

Trentham Lakes

Stoke-on-Trent

Staffordshire

ST4 4TJ

ABOUT YOUR NEW INTREPID GAS STOVE

The Intrepid decorative coal effect gas stoves incorporate a unique and highly developed

fuel bed, which gives the realism of a loose coal layout, combined with realistic flames and

glow. The use of durable hard ceramic material in the construction of the fuelbed

components ensures long and troubles free operation.

When first using the new stove a slight smell may be noticed. This is due to starch used in

the manufacture of the soft ceramic coals, it is non-toxic and will soon disappear.

Please take the time to fully read these instructions, as you will then be able to obtain the

most effective and safe operation of your stove.

IMPORTANT SAFETY INFORMATION

WARNING

This appliance gets to extremely high temperatures and as with all heating

appliances a fireguard should be used for the protection of children, the elderly and

infirm. Fireguards should conform to BS 6539 (1984) (Fireguards for use with solid

fuel appliances).

It is important that this appliance is serviced at least once a year by a CORGI registered

gas installer. The chimney or flue should be visually checked for fallen debris or blockages

which must be removed. The chimney should also be checked to ensure clearance of flue

products. This is a condition of the guarantee.

After installation or during servicing a spillage test must always be carried out.

Rubbish of any type must NEVER be thrown onto the fuel bed, this could affect safe

operation and damage the stove.

Any debris or deposits should be removed from the fuel bed from time to time. This may

be carried out by referring to the cleaning section as described later in this book.

Only the correct number and type of coals must be used and only complete and genuine

replacement sets must be used.

Always keep furniture and combustible materials well clear of the stove and never dry

clothing or items either on or near to the stove. Never use aerosols or flammable cleaning

products near to the stove when it is in use.

The hard ceramic fuel bed remains hot for a considerable period after use and

sufficient time should be allowed for the stove to cool before cleaning etc.

OPERATING THE STOVE

The control is located on the right lower side of the stove in between the front and back

legs. The operation of the stove consists of a control valve with a built in piezo igniter. This

is used to ignite the stove and control the amount of gas flow required. To light the stove

proceed as follows: -

1) Depress the control knob and turn anti-clockwise to the position marked pilot. This will

ignite the pilot, if it fails, continue to hold for a few seconds to purge the gas and repeat.

2) Continue to hold-in the control knob. (The pilot flame can be seen by looking at the

lower left-hand side of the glass panel). Hold the control knob in for 5-10 seconds to allow

the thermocouple to heat up and release, the pilot will now remain lit.

In the unlikely event of a failure of the igniter, the stove can be lit as follows.

Open the doors on the stove. Depress the control knob and turn anti-clockwise to the

position marked pilot. Hold in the control knob for a few seconds to allow the gas to reach

the pilot. Insert the tip of a lit taper into the hole on the burner heat shield located on the

left-hand side of the burner. This will light the pilot flame.

When the pilot has lit, continue to hold the control knob in for 5-10 seconds to allow the

thermocouple to heat up, if the pilot goes out when the control knob is released, repeat the

lighting sequence.

3) It is IMPORTANT that after lighting you must close the doors. Turn the control knob in

the anti-clockwise direction to the high position and the main burner will light.

4) The gas control can be turned clockwise from the maximum position to give the

desired heat output.

WARNING

If the stove goes out for any reason or is turned off and it is necessary to relight the

stove, it is important to allow the stove to cool for 5-10 minutes before attempting to

re-light it.

FITTING THE REMOVEABLE HANDLE TO THE STOVE DOOR

The door handle that comes with the stove is designed to be removable to prevent

overheating during long periods of use. To use the handle, simply slide the collar into

the door handle and open the doors. When you have either opened or shut the doors,

remove the handle and store in a safe place. On Intrepid 3 models, the handle can be

secured in position using the grub screw behind the handle boss, depending on your

aesthetic preference. The Handle, if left attached will become extremely hot in use.

Do not try to open the stove doors when the stove is in operation or without leaving

sufficient time for the handle to cool after use.

WARNING

a) THIS APPLIANCE MUST NEVER BE OPERATED WITH THE DOORS OPEN.

b) IF THE GLASS IS CRACKED OR MISSING THE STOVE MUST NOT BE

USED.

c) THE STOVE IS DEEMED TO BE A WORKING SURFACE AND IS

THEREFORE HOT AND SHOULD NOT BE TOUCHED, EXCEPT FOR THE

CONTROL KNOB AND ADJACENT PANELS.

SPILLAGE MONITORING SYSTEM

This appliance is fitted with a spillage monitoring system, which shuts down the stove if the

evacuation of combustion products from the stove is affected by a partially or fully blocked

flue.

If this system operates the stove will go out. If this occurs, leave the stove for ten minutes

then follow the lighting procedure as described in the previous section. In the event of

repeated operation a specialist must be called to investigate and rectify the cause.

CLEANING

WARNING

Before attempting any cleaning operation ensure that the stove has been allowed to fully

cool.

Cleaning cast iron painted surfaces (Classic Black)

Ensure the stove is cool, The cast iron painted stove usually remains clean and does not

suffer from fingerprints, however occasionally you may need to use a slightly damp cloth to

clean the cast iron surface, it is important that you do this whilst the stove is cool.

If you need to touch-up an area on the stove proceed as follows. Allow the stove to cool.

With a wire brush treat any areas needing attention (only cast iron). Ensure that the

surface is clean and dry.

Touch-up the area with Vermont Castings High Temperature Stove paint.

Take care when using the paint as two coats will give better results than one thick coat.

Cleaning porcelain enamel surfaces (Red enamel or Forest Green)

Ensure the stove has been allowed to fully cool. It is important that water or any other

liquids are not used to clean this appliance. Any fingerprints or marks can usually be

buffed off with a soft cloth. If this fails allow the stove to fully cool and use a damp cloth.

Allow to fully dry before re-lighting, as this will leave streaks on the enamel surface.

Abrasive cleaners, chemical cleaning agents or any type of polish must never be

used. This would expose the cast iron and may stain or begin to rust.

Cleaning the fuelbed

The coals and fuel bed should be periodically examined and any debris or deposits

removed. A vacuum cleaner must not be used to do this as damage to the coals may

result. To remove any deposits from the coals they should be removed from the stove and

placed on a clean sheet of paper (it is advisable to keep the front coals in order and then

each coal can be replaced in the same location). The coals should then be carefully

brushed with a soft brush.

With all coals removed, the fuel bed components and insulating mat may be carefully lifted

out of the stove. The fuel bed components must also be cleaned by gently brushing with a

soft brush. None of these parts must be washed or exposed to any cleaning agents

or water.

Any damaged parts must be replaced by contacting your dealer or telephoning Vermont

Castings on the number stated on the rear cover of this book. Coals must only be

replaced with a complete and genuine replacement set and the stove must never be run

with the wrong number or damaged coals.

The fuelbed must be carefully reassembled as stated in the following section.

Cleaning the glass

Leave the stove to cool completely. Only warm water should be used to clean the glass.

Never use harsh chemicals or abrasives to clean the glass. For any stubborn deposits

contact your local dealer for a suitable cleaning agent.

Cleaning the griddle on the top of the stove (only applicable to Intrepid 2 models).

Leave the stove to cool completely. Due to the griddle been a natural finish, slight

discoloration may occur due to the heat of the appliance. We recommend the use of wire

wool to discard of any rust or deposits. To remove the griddle, open the doors and loosen

the two screws inside the stove at each side of the griddle. Reassemble in reverse order.

SECTION 3

ASSEMBLING THE CERAMICS, AND FUEL BED

a) Place the insulating mat centrally on to the fuelbed support then place the hard

ceramic base on top of the insulating mat, and pull both fully forwards to the burner. Make

sure that the ceramic base is located centrally. Ensure that both parts fit fully down

onto the support and are not lodged on the burner. See below.

b) Place both the hard ceramic fuel bed sections on to the base so that the location lugs

fit snugly into the recesses on the fuel bed sections.

c) Place the Front Ceramic Rails centrally onto the Semi-Circular location plate situated

at the front of the burner. Ensure that the front ceramic rails are located over the front

edge. (See below)

d) Select five of the large coals and locate each one centrally into the depressions in the

Front Ceramic Rail. Ensure that the coals are equally spaced as shown below.

e) Select four of the large coals and two small coals, and place them on the front of the

fuel bed directly behind the spaces between the front row of coals.

f) Place a row of five coals to occupy the spaces behind the second row of coals.

g) Place the remaining four large coals as shown below (Taking care not to allow the

coals to be trapped behind the fuelbed):-

h) Place the remaining three small coals as shown below:-

i) Finally, shut the doors on the stove. Once the doors have been shut, the handle

should be facing downward or similar.

The exact position and fit of the coals may be finely adjusted to give the most pleasing and

random appearance.

Warning: Use only the coals supplied with the stove. When replacing the coals remove

the old coals and discard them. Fit a complete set of coals of the correct type. Do not fit

additional coals or any coals other than a genuine replacement set.

USER REPLACEABLE PARTS

The only user replaceable parts on this stove are the fuelbed components and coals,

which may be replaced as described in the above section. Replacement of any other

parts must be carried out by a competent person such as a CORGI registered gas

installer.

The part numbers of the user replaceable parts are as follows, these are available from

VERMONT CASTINGS,INC who may be contacted at the address shown on the rear

cover.

Fuelbed base 100-17920

Left Hand Fuelbed 100-17930

Right Hand Fuelbed 100-17940

Replacement Coal Set 100-17860

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vermont Castings Herd Handbücher

Vermont Castings

Vermont Castings OXDV30NVSB Bedienungsanleitung

Vermont Castings

Vermont Castings 2950 Bedienungsanleitung

Vermont Castings

Vermont Castings The Aspen II 1405CE Montageanleitung

Vermont Castings

Vermont Castings Encore 2550 Bedienungsanleitung

Vermont Castings

Vermont Castings RFSDV34 Montageanleitung

Vermont Castings

Vermont Castings 1975 Bedienungsanleitung

Vermont Castings

Vermont Castings ACSG Bedienungsanleitung

Vermont Castings

Vermont Castings Jefferson 2822 Montageanleitung

Vermont Castings

Vermont Castings 1991 Defiant Encore 2190 Bedienungsanleitung

Vermont Castings

Vermont Castings Resolute Technisches Handbuch

Vermont Castings

Vermont Castings 3349 Montageanleitung

Vermont Castings

Vermont Castings 2190 Bedienungsanleitung

Vermont Castings

Vermont Castings Encore Bedienungsanleitung

Vermont Castings

Vermont Castings Reliance Bedienungsanleitung

Vermont Castings

Vermont Castings Encore Flexburn 2040 Montageanleitung

Vermont Castings

Vermont Castings Radiance RUVS40 Montageanleitung

Vermont Castings

Vermont Castings RFSDV24 Bedienungsanleitung

Vermont Castings

Vermont Castings Vigilant II 2310 Montageanleitung

Vermont Castings

Vermont Castings Encore 2550C Bedienungsanleitung

Vermont Castings

Vermont Castings The Intrepid II 1990 Montageanleitung

Vermont Castings

Vermont Castings 1975CE CE Montageanleitung

Vermont Castings

Vermont Castings Intrepid II Bedienungsanleitung

Vermont Castings

Vermont Castings Addison 2905 Bedienungsanleitung

Vermont Castings

Vermont Castings SNV30 Montageanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung

Barton

Barton FH-AMP8745 Technisches Dokument

United States Stove Company

United States Stove Company Ashley AP60 Bedienungsanleitung