Vertiv LIEBERT RPC2 Bedienungsanleitung

LIEBERT® RPC2™

COMMUNICATIONS MODULE

Quick Installation Guide

SL20842_Rev3/590-1771-501A 1

The RPC2™ Communications

Module provides network and

environmental sensor connectivity

for the Liebert™ rack PDU family of

products. It provides Ethernet and

serial communication interfaces as

well as the ability to connect up to

four rack PDUs in an array, sharing

one IP address. Devices powered

by a rack PDU can be remotely

controlled and monitored through

the RPC2’s various interfaces. The

RPC2 also supports the connection

of an optional external LCD display.

Please see the RPC2

Communications Module Installer/

User Guide for further information.

The following are instructions to

install and configure the

communications module in the

rack PDU.

Setting up the RPC2

Communications Module

The RPC2 can be accessed either

via DHCP (factory default) or static

IP boot mode through the network

(LAN) port. To find the DHCP IP

address, see the MPH2™ Rack PDU

Installer/User Guide. To configure

the static IP boot mode, the

network settings must be changed

via the link port as follows.

1. Locating the

communication card bay

Find the communication card

bay on the rack PDU. It may

have a removable cover.

2. Inserting the RPC2

communications module

Insert the RPC2

communications module into

the card bay and secure it by

tightening the captive

thumbscrews.

NOTE: The RPC2 factory

default boot mode is DHCP for

the LAN port, so no changes

are necessary.

3. Connecting a laptop

Connect a CAT5 Ethernet cable

(not included) from a laptop to

the RPC2’s link port.

NOTE: Do not connect the link

port to your network. The

RPC2’s link port should only be

used for local configuration or

linking together a Rack PDU

Array™.

4. Configuring the RPC2

through the link port

To establish communication

through the link port, first

configure the laptop’s Ethernet

adaptor with the following

settings:

IP Address: 192.168.1.9

Subnet mask: 255.255.255.252

Default gateway: 192.168.1.1

5. Entering the link port IP

address

Open a web browser and enter

192.168.1.10. When prompted,

enter admin for both the login

and the password and click the

6. Configuring the network

Click the System tab and click

Settings - Network in the

navigation tree. Click the Edit

icon in the right pane. Select

Static for the IPV4 Boot Mode

and enter the IP address,

subnet mask and default

gateway in the proper fields.

See your network administrator

for these settings.

RPC2™ Communications Module Installation

Link NetworkDisplay

Sensor

Serial

USB Micro-AB

To contact Vertiv Technical Support: visit www.VertivCo.com

trademarks or registered trademarks of their respective owners. While every precaution has been taken to ensure accuracy and completeness herein, Vertiv Co. assumes no

responsibility, and disclaims all liability, for damages resulting from use of this information or for any errors or omissions. Specifications are subject to change without notice.

LIEBERT® RPC2™ COMMUNICATIONS MODULE

Quick Installation Guide

2 SL20842_Rev3/590-1771-501A

7. Restarting the RPC2

Click the Save icon when

finished and click the Reboot

icon to restart the RPC2.

Disconnect the cabling at the

link port. Connect the

CAT5/5E/6 cable from the LAN

to the RPC2 communication

module’s network port.

8. Creating a Rack PDU

Array

Connect a CAT5 Ethernet cable

to the link port of the master

RPC2. Then connect the other

end of the CAT5 Ethernet cable

to the network port of a sibling

RPC2 on a second MPH2. This

rack PDU is now a sibling unit

and is accessible through the

master RPC2. Two additional

rack PDUs can be connected to

the array by following the same

cabling procedure. Each newly

added rack PDU is discovered

as the next sibling.

NOTE: The rack PDU array

supports up to four RPC2

communication modules.

NOTE: If the array order needs to

be changed, disconnect the

cabling for at least 30 seconds.

Then reconnect as desired. It is not

necessary to reboot or power cycle

the RPC2 communications module.

Rack PDU Array Configuration

Master Sibling SiblingSibling

Andere Handbücher für LIEBERT RPC2

Andere Vertiv Steuereinheit Handbücher

Vertiv

Vertiv Liebert MBSM Bedienungsanleitung

Vertiv

Vertiv R48-500 Bedienungsanleitung

Vertiv

Vertiv NetSure R48-2000 Bedienungsanleitung

Vertiv

Vertiv eSure R48-2000e3 Bedienungsanleitung

Vertiv

Vertiv LIEBERT RPC2 Betriebsanleitung

Vertiv

Vertiv NetSure R24-3000 Bedienungsanleitung

Vertiv

Vertiv eSure R48-3500e3 Bedienungsanleitung

Vertiv

Vertiv Liebert iCOM Montage- und Wartungsanleitung

Vertiv

Vertiv NetSure M831A Bedienungsanleitung

Vertiv

Vertiv NetSure Series Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

Vertiv

Vertiv NetSure7100 Series Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

Vertiv

Vertiv Liebert SmartAisle2 Bedienungsanleitung

Vertiv

Vertiv eSure S48-2000e3 Bedienungsanleitung

Vertiv

Vertiv Geist Stücklistenhandbuch

Vertiv

Vertiv eSure R48-1000e3 Bedienungsanleitung

Vertiv

Vertiv Liebert iCOM Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert NXL Bedienungsanleitung

Vertiv

Vertiv Liebert CW Montage- und Wartungsanleitung

Vertiv

Vertiv LIEBERT MPX PEM Bedienungsanleitung

Vertiv

Vertiv Net Sure SM-DU+ Bedienungsanleitung

Vertiv

Vertiv MPUIQ-VMCHS Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung