VEVOR VVPS115BUS Bedienungsanleitung

USER MANUAL

SINGLE SPEED POOL PUMP

Instruction Manual

VVPS115BUS(1.5THP 115V)

VVPS120BUS(2.0THP 115V)

IMPORTANT : Be sure to review the contents of this manual before attempting to operate the equipment.

This manual should be located where it can be easily referenced by all users of themachine.

NEED HELP? CONTACTUS!

Have product questions? Need technical suppo? Please feel free to contact us:

CustomerSe[email protected]

Read this "Safety Precautions" before operation.

The below information should not be neglected for the proper use of this product. Your

understanding can prevent harm or danger to the user or others.

SAFETY PRECAUTIONS

MAIN PARTS

PARTS

1.Lid & Clamp Ring

2.O-Ring

3.Strainer

4.Clip-Bayonet

5.Strainer body

6.Drain Plug

7.Diuser O-Ring

8.Bolts

9.Diuser

10.Pump Housing O-Ring

11.Impeller

12.Pump Housing

13.Motor

14.Shaft Seal

ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE

INSTALLATION, OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO

THE END-USER OF THIS PRODUCT. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD

RESULT IN SERIOUS INJURY.

READ CAREFULLY AND SAVE THIS INSTRUCTION MANUAL

INSTALLATION

The following information is ve impoant for safety in

handling this product. Be sure to obsee it.

Indicates an imminently hazardous situation that, if not avoided, will result

in death or serious inju.

DANGER

Indicates a potentially hazardous situation that, if not avoided, could

result in death or serious inju.

WARNING

Indicates a potentially hazardous situation that, if not avoided, may

result in minor or moderate inju, or propey damage.

CAUTION

ALERT

PROHIBITED

IMPORTANT

Do not operate the pool and spa circulation system if a system component is not assembled

properly, damaged, or missing.

Before staing the system pump, all system valves must be set to allow system water to

return to the pool.

Remove pressure test plugs and/or plugs used in winterization of the pool/spa from the

suction outlets. Fail to do so will result in an increased potential for suction entrapment.

Connect only to a branch circuit protected by a ground-fault circuit interrupter (GFCI).

Before working on any electrical equipment, turn o the power supply to the equipment.

Do not permit children to play with this product.

WARNING

Strainer cover must be properly secured to prevent violent separation due to pressure in

the circulation system.

Before seicing, turn all the circulation system and pump controls o, make sure the lter

manual air relief valve is in the open position, and all pressure is relieved.

It is highly recommended that this product be installed and seiced by a qualied pool

professional.

Stay o the main drain and away from all suction outlets.

DANGER

Before seicing, all water circulation systems and pump controls must be o

position and release all the pressure from the system.

INSTALLATION

Use Teon tape on the thread before screw ttings to pump inlet and outlet pos so as to avoid

leakage. Do not over-tighten the ttings.

Warning: Keep product away from Children.

This pump is compatible with above-ground pools and spas. Locate the pump as close to the

pool and water level as possible. Do not add too many elbow pipes in the plumbing so as to

avoid suction reduction. It is highly recommended that the pump be placed in cool, d

places and avoid direct sunlight. Install the pump on a rm, level base or pad to meet all local

and national codes. Fasten the pump to a base or pad with screws or bolts to fuher reduce

vibration and stress on pipe or hose joints. The base must be solid, level, rigid, and

vibration-free.

WARNING: This product should be installed and seiced by a qualied pool professional.

All electrical wiring must be in conformance with applicable local codes, regulations, and

the National Electric Code (NEC).

It is strongly advised to protect the electrical components from direct sunlight though

this pump is designed for outdoor use.

If installed within an outer enclosure or beneath the ski of a hot tub or spa, adequate

ventilation and free circulation of air must be provided to prevent overheating.

Place this pump in a well-drained area, one that will not ood when it rains.

Do not install this pump in a damp or non-ventilated location. It requires free circulation

of air for cooling.

Do not run the pump d. Water acts as a coolant and lubricant for the mechanical shaft

seal. Running the pump d may damage seals, causing leakage, ooding, and voids

warranty. Fill strainer housing with water before staing the motor.

CAUTION

THP 1.5 2.0

L12.01"(305mm) 12.76"(324mm)

• Remove pump lid and Strainer.

• Remove clip-bayonet (pa# 4 in the pas list).

• Remove the pump strainer body from the pump housing.

• Unscrew the 8 bolts.

• Turn the discharge po to be horizontal.

• Screw back the 8 bolts.

• Re-install the pump strainer body.

• Buckle up the clip-bayonet.

• Put Strainer back into the pump strainer body.

• Fasten pump lid

Make sure that the electrical supply available is suitable for the motor’s voltage, phase, and cycle.

Voltage from the power must be in the range from 90% to 110% of the motor nameplate rated voltage.

Otherwise, the motor may overheat and result in overload tripping and reduced component life.

Install, ground, bond, and wire motor in accordance with local or NEC requirements.

The motor should be grounded permanently by connecting the ground terminal to the electrical

seice ground.

Bond motor to pool structure. Bonding will connect all metal pas within and around the pool with a

continuous wire. Bonding reduces the risk of current passing between bonded metal objects, which

could potentially cause electrical shock if grounded or shoed.

Pump discharge po can be turned to horizontal:

TROUBLE SHOOTING

MOTOR WILL NOT START

• Improper or loose wiring connections; open switches or relays; tripped circuit breakers,

GFCI’s, or blown fuses.

• Manually check rotation of motor shaft for free movement and lack of obstruction.

• If you have a timer, make sure it is working properly. Bypass it if necessa.

MOTOR SHUTS OFF

MOTOR HUMS BUT DOES NOT START

• Undersized wiring; loose connections; etc.

• Low voltage at motor or power drop (frequently caused by undersized wiring or extension cord use).

• Mechanical binding and electrical overload.

• Centrifugal switch stuck in the OPEN position.

• Binding of the motor shaft.

PUMP WON’T PRIME

•Make sure pump strainer housing is lled with water and the cover O-ring is clean; also, be sure it is

properly seated in the cover O-ring groove. Make sure the strainer cover is locked rmly in position

and lubricated with “Jack’s 327”.

• Make sure all suction and discharge valves are fully open and not blocked, that the pool water level

is at a proper level and that the skimmer weir is not hung up or stuck on the skimmer wall.

• Block o to determine if the pump will develop a vacuum. You should have 5”-6” of vacuum at the

strainer cover. You may be able to check by removing the skimmer basket and holding your hand over

the bottom po with the skimmer full and pump running. If no suction is felt, check for line blockage.

• a. If pump develops a vacuum, check for a blocked suction line or diy strainer basket, and an air

leak in the suction piping may be the cause.

• b. If the pump does not develop a vacuum and the pump has sucient “priming water”: i. Re-check

strainer housing cover and all threaded connections for suction leaks. Check if all hose clamps are

tight. ii. Check voltage to ensure that the motor is rotating at full RPM. iii. Open housing cover and

check clogging or obstruction in suction. Check impeller for debris. iv. Remove and replace shaft seal

only if it is leaking.

PRIMING

Fill strainer housing with water to suction pipe level. If water leakage occurs anywhere on the pump or

lter, DO NOT sta the pump. If no leakage occurs, stand at least 10 feet from the pump and/or lter

and proceed with staing the pump.

TROUBLE SHOOTING(CONTINUED)

LOW FLOW

• Clogged or restricted strainer or suction line; undersized pool piping.

• Plugged or restricted discharge line or lter, valve paially closed (high gauge reading).

How to correct: Backwash strainer as per manufacturer’s instructions;

• Air leak in suction piping causing rumbling in the pump.

• Cavitation due to restricted or undersized suction line or leak at any joint, low water

level in the pool, and unrestricted discharge return lines. Correct suction condition or

throttle return lines, if practical.

NOISY PUMP

•Vibration due to improper mounting, etc. Put a rubber pad under metal mounting feet.

• Foreign matter in the pump housing. Loose stones/debris hitting the impeller could be the

cause; remove any above.

• Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals

causing seal damage which will allow chlorinated water to seep into bearings wiping out

the grease causing bearing to whine. All seal leaks should be replaced at once.

• Equipment base vibrating.

E-mail: CustomerSeice@vevor.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VEVOR Schwimmbadpumpe Handbücher

VEVOR

VEVOR HCP370A-D Bedienungsanleitung

Beliebte Schwimmbadpumpe Handbücher anderer Marken

TIP

TIP STEAM 35000 INV Verdrahtungsschema

Jacuzzi

Jacuzzi J-HI27C Bedienungsanleitung

PoolRite

PoolRite SQI 400 Bedienungsanleitung

Pentair

Pentair IntelliComm Bedienungsanleitung

Calpeda

Calpeda NMP Bedienungsanleitung

WilTec

WilTec 50374 Bedienungsanleitung

Evolution

Evolution Evoflow Storm Eco-V Bedienungsanleitung

AquaTools

AquaTools AT240701 Bedienungsanleitung

Sibo

Sibo AquaForte RD352 Bedienungsanleitung

CLS

CLS VICTORIA PLUS SILENT Bedienungsanleitung

Pond One

Pond One Piranha 800 Bedienungsanleitung

Hayward

Hayward VSP Bedienungsanleitung

Resol

Resol DeltaSol B Pro Bedienungsanleitung

Evolution Aqua

Evolution Aqua UniTech Perfect 5000 Bedienungsanleitung

Outside Living Industries

Outside Living Industries Ubbink Heatermax Pool Kurzanleitung

CPI

CPI Olympic 2P1815 Bedienungsanleitung

Flotec

Flotec FP6121-01 Bedienungsanleitung

Pentair

Pentair ONGA LEISURETIME LTP400 Bedienungsanleitung