VIA Technologies MVP3 Bedienungsanleitung
VIA MVP3
AT
SYSTEM BOARD
OPERATION MANUAL
DOC NO. UM-VMD-E2………………………………………………………………………………………………………………………………….PRINTED IN TAIWAN
MVP3 SYSTEM BOARD TABLE OF CONTENTS
i
TABLE OF CONTENTS
Chapter & Section Page
1. INTRODUCTION .............................................................................................. 1-1
1.1 SYSTEM OVERVIEW ................................................................................ 1-1
1.2 SYSTEM BOARD LAYOUT ...................................................................... 1-2
2. FEATURES......................................................................................................... 2-1
2.1 MAINBOARD SPECIFICATIONS ........................................................... 2-1
3. HARDWARE SETUP ........................................................................................ 3-1
3.1 UNPACKING................................................................................................ 3-1
3.2 HARDWARE CONFIGURATION............................................................ 3-2
3.2.1 CONNECTORS.................................................................................. 3-2
3.2.2 JUMPERS ........................................................................................... 3-9
3.2.3 SUGGESTED MEMORY MODULES ............................................ 3-22
4. AWARD BIOS SETUP ...................................................................................... 4-1
4.1 GETTING STARTED.................................................................................. 4-1
4.2 MAIN MENU................................................................................................ 4-3
4.3 CONTROL KEYS ........................................................................................ 4-4
4.4 STANDARD CMOS SETUP....................................................................... 4-5
4.5 BIOS FEATURES SETUP .......................................................................... 4-6
4.6 CHIPSET FEATURES SETUP .................................................................. 4-11
4.7 POWER MANAGEMENT SETUP............................................................ 4-14
4.8 PNP/PCI CONFIGURATION .................................................................... 4-19
4.9 INTEGRATED PERIPHERALS................................................................ 4-22
4.10 LOAD SETUP DEFAULTS ...................................................................... 4-25
4.11 SUPERVISOR PASSWORD / USER PASSWORD............................... 4-26
4.12 IDE HDD AUTO DETECTION ............................................................... 4-26
4.13 HDD LOW LEVEL FORMAT ................................................................. 4-28
4.14 SAVE &EXIT SETUP ............................................................................... 4-29
4.15 EXIT WITHOUT SAVING....................................................................... 4-30
MVP3 SYSTEM BOARD
ii
TRADEMARKS
All trademarks used in this manual are the property of their respective owners.
NOTE
The “LOAD SETUP DEFAULTS” function loads the default settings directly from BIOS
default table, these default settings are the best-case values that will optimize the system
performance and increase the system stability. This strongly recommended when you first
receive this system board, or the system CMOS data is corrupted.
Move the selection bar to “LOAD SETUP DEFAULTS” and then press the “ENTER” key
and then the SETUP default values will be loaded into the system. (Please refers to the
Chapter 4 AWARD BIOS SETUP procedures in this manual.)
NOTICE
Information presented in this manual has been carefully checked for reliability; however,
no responsibility is assumed for inaccuracies. The information contained in this manual is
subject to change without prior notice.
MVP3 SYSTEM BOARD INTRODUCTION
1-1
1. INTRODUCTION
1.1 SYSTEM OVERVIEW
This mainboard is an AT form-factor PCI Local Bus Pentium system board with the
updated AGP technology designed onboard. The most updated VIA MVP3 chipset for
100MHz Front Side Bus (FSB) is designed on the board.
This mainboard is designed for the high performance Pentium or other equivalent
processors for high-end application and it is a true GREEN-PC computer system. The
FSB clock speed can be adjusted to 100MHz when we are installing the processors
with 100MHz FSB speed.
This system board supports the Peripheral Component Interconnect (PCI) Local Bus
standard (PCI Specification Rev. 2.1 compliant). It not only breaks through the I/O
bottlenecks of the traditional ISA mainboard, but also provides the ultra high
performance for networking and multi-user environments.
The mainboard has built-in two channels PIO and Bus Master Enhanced PCI IDE port,
one Floppy Disk control port, two high speed Serial ports (UARTs), one multi-mode
Parallel port, one AT keyboard port, one PS/2 mouse port, one IR port, two USB ports.
The Accelerated Graphic Port (A.G.P.) on the board is designed for the updated AGP
3D video display card. Unlike the traditional PCI-based display cards, AGP technology
provides lightening data throughput to fully facilitate the 3Diminsional and multimedia
graphic display. The data transfer rate on the AGP port can be as fast as 133MHz and it
is much faster than the traditional 33MHz PCI VGA cards.
The AGP is a new video display technology and it requires the device driver or new
operating system to enable the accelerated graphic feature. Windows®98 will supports
AGP directly, but Windows® 95 still needs the appropriate device drivers to enable the
AGP feature. Please don’t worry about the device driver, you can always find the
device driver included in the AGP card.
MVP3 SYSTEM BOARD INTRODUCTION
1-2
1.2 SYSTEM BOARD LAYOUT
The following picture displays the position of all connectors and jumpers. Please
refer to the following sections for the detail description.
ISA 3
ISA 2
ISA 1
PCI 2
PCI 1
AGP
K/B
CPU
PCI 3
Battery
DIMM 2
DIMM 1
COMA
CN7 LPT
CN9 IDE2
CN5
CN6
CN11 IDE1
COMB
CN13 FDC
CN8
AT POWER
JP14~JP18
Jumper setting
for CPU Voltage
(Please see the jumper setting)
JP1~JP10
Jumper setting
for CPU Frequency
(Please see the jumper setting)
KEYLOCK
1 2 3 4 5
SPK
Connector
1 2 3 4
DIMM 3
CN16
ATX POWER
CN4 USBCN10 IR CN3
PS/2 MOUSE
1
G G G G
111
“G” = Ground
P
W
S
L
H
L
R
S
JP12 Clear CMOS
CN14 CPU Fan Conn.
CN2
AT K/B
DIMM SOCKETS
CN15 WOL
CN12
Chassis Fan
MVP3 SYSTEM BOARD FEATURES
2-1
2. FEATURES
2.1 MAINBOARD SPECIFICATIONS
¨Chipset
VIA MVP3 (VT82C598MVP, VT82C586B) and Winbond W83877F / TF.
¨CPU
Intel : Pentium processor and OverDrive processor
90 / 100 / 120 / 133 / 150 / 166 / 200 / 233 MHz.
Cyrix : 6x86 / 6x86L - P150+ / P166+ / P200+.
6x86MX - PR166 / PR200 / PR233,6x86MII - 266/300/333/366.
AMD : K5 - PR90 / PR100 / PR120 / PR133 / PR150 / PR166.
K6 / PR2-166 / 200 / 233 / 266/ 300
K6-2 /266 / 300 / 333 / 350 /366 / 380 / 400 / 450.
K6-3 /400 / 450.
IDT : Win Chip C6-180 / 200 / 225 / 240.
Win Chip 2 -200 / 233 / 266 / 300.
¨CPU Voltage
(1).CPU I/O voltage : “+3.3V DC” or ”+3.5V DC”.
(2).CPU CORE voltage: +1.3V DC ~ +3.5V DC.
¨System Clock
60 / 66 / 75 / 83 / 95 / 100 MHz
¨Memory
DRAM : Three banks, each bank can be single or double sided, 8MB up to 1GB.
Supports Extended Data Out (EDO), and SDRAM memory (Use 168-pin
DIMM module x3). Support +3.3V DC operating voltage on DIMM
sockets.
SRAM : 512KB pipelined burst SRAM on board.
¨BIOS
AWARD System BIOS. 128KB x 8 Flash ROM (for Plug & Play BIOS).
MVP3 SYSTEM BOARD FEATURES
2-2
¨Expansion Slots
AGP Slots: 32-bit x 1 (Supports 1x/2x AGP graphics cards)
PCI Slots : 32-bit x 3 (All Master / Slave, PCI 2.1 Compliant).
ISA Slots : 16-bit x 3 (PCI / ISA slot share one slot).
¨IDE Ports
Two channel PIO and “Ultra DMA/33” Bus Master PCI IDE ports, which will
connect maximum 4 IDE devices like IDE Hard Disk and ATAPI CD-ROM device.
PIO Mode 4 transfer rate up to 14 Mbytes/s transfer rates and supports “Ultra
DMA/33” mode transfers up to 33 Mbytes/sec.
¨USB Ports
Two Universal Serial Bus (USB) ports.
¨Super I/O Ports
1.Two high speed NS16C550 compatible Serial ports (UARTs).
2.One SPP / EPP / ECP mode Bi-directional parallel port.
3.One Floppy Disk Control port.
¨WOL Port (Active only with ATX power supply)
One WOL connector supports Wake-On-LAN (WOL up-designed)
¨IR Port
One HPSIR and ASKIR compatible Infrared port. (FIR is optional )
¨Mouse and Keyboard
Supports PS/2 Mouse connector, PS/2 Keyboard connector (optional) and AT
Keyboard connector.
¨Software compatibility
MS-DOS, Windows NT, OS/2, UNIX, NOVELL, MS Windows, CAD/CAM,
Windows 98 , ...etc.
¨DIMENSION
Width & Length : 220 mm x 220 mm.
Height : 3/4 inches with components mounted.
PCB Thickness : 4-layers, 0.05 inches normal.
Weight : 20 ounces.
MVP3 SYSTEM BOARD FEATURES
2-3
¨ENVIRONMENT
Operating Temperature : 10°C to 40°C. (50°F to 104°F).
Require Airflow : 50 linear feet per minute across CPU.
Storage Temperature : -40°C to 70°C. (-40°F to 158°F).
Humidity : 0 to 90% non-condensing.
Altitude : 0 to 10,000 feet.
MVP3 SYSTEM BOARD HARDWARE SETUP
3-1
3. HARDWARE SETUP
This chapter explains how to configure the mainboard hardware. When you are
installing the mainboard, you will have to make jumper settings and cable
connections. Please refer to the following sections for the details:
3.1 UNPACKING
The system board package contains the following parts :
This system board.
Operation manual.
Cable set for IDE and I/O device.
One CD diskette which includes device driver and utility program
The mainboard contains electric sensitive components which can be easily damaged
by static electricity, please leave the mainboard sealed in its original packing until
when installation.
Unpacking and installation shall be done on a grounded anti-static mat. The operator
will have to wear an anti static wristband, grounded at the same point as the anti-
static mat.
Inspect the mainboard carton to see whether there is any obvious damage. Shipping
and handling may cause damage to your board. Be sure there is no shipping or
handling damages on the board before proceeding.
After opening the motherboard color box, extract the mainboard and place it only on
a grounded anti-static surface with the component side up. Inspect the board again to
see whether there is any damage.
Press on all of the socket IC‘s to make sure that they are properly seated. Do this
only with the board placed on a firm flat surface.
MVP3 SYSTEM BOARD HARDWARE SETUP
3-2
3.2 HARDWARE CONFIGURATION
Before the system board is ready for operating, the hardware must be configured to
make sure it will work properly with different environment. To configure the system
board is a simple task, only a few jumpers, connectors, cables and sockets needs to
be selected and installed.
3.2.1 CONNECTORS
A connector is two or more pins that are used make connections to the system
standard accessories (such as power, mouse, printer,...etc.). The following is a list
of connectors on board, as well as descriptions of each individual connector.
(A) BAT1 Non-rechargeable battery (Using 3V Lithium battery : CR2032)
Pin # Assignment
+ Battery Positive
- Ground
(B) CN2 AT Keyboard connector
Pin # Assignment Pin # Assignment
1 Keyboard Clock 2 Keyboard Data
3 No Connection 4 Ground
5+5VDC
(C) CN3 PS/2 Mouse connector
Pin # Assignment
1●1 Mouse Data
2 2 No Connection
3●3 Ground
4●4+5VDC
5●5 Mouse Clock
Inhaltsverzeichnis
Andere VIA Technologies Hauptplatine Handbücher
VIA Technologies
VIA Technologies VB8001 Bedienungsanleitung
VIA Technologies
VIA Technologies P4M800 Gebrauchsanweisung
VIA Technologies
VIA Technologies EPIA-M840 Bedienungsanleitung
VIA Technologies
VIA Technologies VB8002 Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-M10000G - VIA Motherboard - Mini ITX Bedienungsanleitung
VIA Technologies
VIA Technologies VB7002 Bedienungsanleitung
VIA Technologies
VIA Technologies PT-TVBT Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-P820 Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-EN15000G - VIA Motherboard - Mini ITX Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-EK10000G - VIA Motherboard - Mini ITX Bedienungsanleitung
VIA Technologies
VIA Technologies NAS 7800 Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-P710 Bedienungsanleitung
VIA Technologies
VIA Technologies KM400 Gebrauchsanweisung
VIA Technologies
VIA Technologies EPIA-P830 Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-P700 Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-PE Bedienungsanleitung
VIA Technologies
VIA Technologies EPIA-CN13000G - VIA Motherboard - Mini ITX Bedienungsanleitung
VIA Technologies
VIA Technologies VAB-950 Sicherheitsleitfaden
VIA Technologies
VIA Technologies EPIA-ML8000AG - VIA Motherboard - Mini ITX Bedienungsanleitung
VIA Technologies
VIA Technologies VIA KT266A ChipsetMotherboard Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
