ViaSat SurfBeam 2 Bedienungsanleitung

SurfBeam 2 Antenna Test

Release Date: October 2013

Page 1of 5

Proprietary –For use only pursuant to

company approval and instructions

Summary

This Job Aid covers:

Purpose

Process

Possible Results

Tools Required

Required Escalation Data

Test Details

This Job Aid supports all Technician audiences. Every ViaSat Repair Service Call begins and ends with a

Service Visibility Tool (SVT) Analysis. This test is not an isolated test; follow the appropriate Trouble

Isolation Check Sheet for complete testing.

This test applies to the following 75cm ODUs: VS1100, VS1101, and VS1200. These antennas use the

SurfBeam 2 modem, and deliver the Exede service.

Purpose

Use the Antenna Test to discover if the satellite antenna is aligned correctly or if there is a TRIA failure.

Process

Step

Action

Validate Point and Peak settings and Modem Key

Disconnect Customer Equipment from the modem and connect the powered Technician Laptop

Computer

Reset the modem at TRIA by covering the feedhorn with the Inclinometer bracket. Wait one minute,

and then remove the bracket. The TRIA should emit the ‘beep bop’ tone if the modem has reset.

Reset Skew to 90 degrees

Re-center Fine Azimuth Adjustment bolt.

Re-set Elevation to Boom Arm Angle.

Reboot Modem.

Open Laptop Computer Browser and type in URL: http://192.168.100.1/install

Use standard SurfBeam 2 Point and Peak process to correct antenna pointing errors

10.

When all the progress indicators display green and status text displays ‘Online’ in the Modem

State field on the Modem/IFL Cable Status page, test has PASSED

If the Modem State field displays progress indicators in gray or yellow and/or the status text does

not display ‘Online’, test has FAILED

Important: The only acceptable result of this test is PASSED. The Technician repeats the test

until all errors are found and the test is PASSED. The only exceptions are failures that require

escalation or when there is a Network outage during the test, where the result is INCOMPLETE.

SurfBeam 2 Antenna Test

Release Date: October 2013

Page 2of 5

Proprietary –For use only pursuant to

company approval and instructions

Step

Action (continued)

11.

Observe Modem Lock process

viewing the Modem LEDs:

Power LED –Solid

RX flashing, then goes

solid

TX flashing, then goes

solid

Ethernet –flashes, then

goes solid

12.

Validate Modem Lock process

viewing the Status Icons and

Status Text displayed in the

Modem State field on the

Modem/IFL Cable Status page

of the Modem Browser

Interface (MBI).

Possible Results

INCOMPLETE

oConfirmed Network Outage

oReschedule, if necessary

PASSED

oPoint and Peak correction made

oValidate with Modem Lock Test

PASSED

oCable Replaced/Repaired

oValidate with Modem Lock Test

PASSED

oTRIA Replaced

oValidate with Modem Lock Test

PASSED

oModem Replaced

oValidate with Modem Lock Test

FAILED

oOld TRIA/Modem re-installed

oModem Status stuck at Scanning,

Syncing, and/or Ranging/Ranged

oModem Status stuck at Network

Entry, DHCP, or Undefined

oValidate escalation data, and follow

normal Escalation process

SurfBeam 2 Antenna Test

Release Date: October 2013

Page 3of 5

Proprietary –For use only pursuant to

company approval and instructions

Tools Required

Technician Laptop Computer

Inclinometer Bracket

Compass

Inclinometer

7/16 Inch open-end wrench

Ratchet wrench with sockets

Required Escalation Data

New Arm Angle

New Azimuth

New Skew

Old/new TRIA serial number (if replacement)

Test run results and result actions

Modem LED status and Status Text from Modem/IFL Cable Status page

Test Details

Follow these steps to complete the SurfBeam 2 Antenna Test:

Step

Action

Validate that the appropriate pre-tests are complete as detailed on the Trouble Isolation Check

Sheet.

Validate Point and Peak Settings and Modem Key on the Support Portal Quick Flash page for the

account.

Disconnect Customer Equipment (Computer, Router, or ATA) from the modem.

Using the existing Ethernet cable, connect the powered Technician Laptop Computer to the

SurfBeam 2 Modem.

Reset the modem at TRIA by covering the feedhorn with the Inclinometer bracket. Wait one minute,

and then remove the bracket. The TRIA should emit the ‘beep bop’ tone if the modem has reset.

Note: Never use a hand or other body part to block the feedhorn.

Reset Skew to 90 degrees as outlined in the SurfBeam 2 Assembly Job Aid.

Re-center the Fine Azimuth adjustment as outlined in the SurfBeam 2 Assembly Job Aid.

Use the Inclinometer to point the Boom Arm Angle; point the Elevation.

Set the Boom Arm Angle by subtracting 19.4 from the Elevation.

SurfBeam 2 Antenna Test

Release Date: October 2013

Page 4of 5

Proprietary –For use only pursuant to

company approval and instructions

Step

Action (continued)

Disconnect the AC power plug from the power source to power down the modem.

10.

Reconnect the AC power plug to power up the modem and wait for the RX LED to begin flashing.

11.

Open Laptop Computer Browser and type in URL: http://192.168.100.1/install to put the Modem in

Installation Mode.

12.

On the Installation Configuration page, type the Modem Key into the appropriate fields.

13.

After the Modem Key is entered, click the Forward Arrow button to open the Modem/IFL Cable

Status page.

Important: Do not press the Enter key. Pressing the Enter key takes the modem out of

Installation Mode.

14.

Validate the following:

1. The SB2 Modem RX and LAN LEDs are flashing in unison

If the RX/LAN LEDs are not flashing correctly:

oReplace Modem.

oRestart this test at step 10.

2. The TRIA is emitting the Heartbeat tone

If the TRIA heartbeat is not heard:

oReplace TRIA.

oRestart this test at Step 10.

If the Technician hears the TRIA heartbeat, and sees the RX/LAN LEDs flashing correctly, go to

Step 15.

15.

Re-point and re-peak the antenna using the standard process outlined in the 75cmODU/SurfBeam 2

Point and Peak Job Aid.

16.

When the realignment is complete, return to the Installation Configuration Page.

If the third box in the Course to Fine Pointing section displays a green checkmark, go to step

17.

If the third box in the Course to Fine Pointing section does not display a green checkmark,

return to antenna and complete a Push/Pull test. Return to the Installation Configuration

page.

oIf the third box in the Course to Fine Pointing section now displays a green

checkmark go to step 17

oIf the third box in the Course to Fine Pointing section still does not display a green

checkmark

1. Replace the TRIA.

2. Restart this test at Step 9.

17.

After the green checkmark displays in the third box in the Course to Fine Pointing section on the

Installation Configuration page, click on the Forward Arrow button to start the Modem Lock

process and open the Basic Status page.

Important: Do not press the Enter key. Pressing the Enter key will take the modem out of

Installation Configuration mode.

SurfBeam 2 Antenna Test

Release Date: October 2013

Page 5of 5

Proprietary –For use only pursuant to

company approval and instructions

Step

Action (continued)

18.

On the Basic Status page, click the Modem button to open the Modem/IFL Cable Status page.

19.

On the Modem/IFL Cable Status page, observe the progress indicators and status text displayed in

the Modem State field.

20.

Results:

For a successful Modem Lock, the progress indicators all display green and the status text

displays 'Online'; the test is PASSED.

If progress indicators are stuck at Scanning/Syncing, and/or Ranging/Ranged:

1. Correct the following errors:

a. Network Outage: confirm with Installation Support Team and reschedule, if

necessary; the test is INCOMPLETE

b. Cable: Repair/replace cable and restart test at step 5

c. LOS: Correct alignment and restart test at step 5

d. TRIA: Replace TRIA and restart test at step 5

e. Modem: Replace Modem and restart test at step 5

2. If the progress indicators all display green in the restarted test, and the status text

displays 'Online'; the test is PASSED

3. If the restarted test halts at Scanning, Syncing, and/or Ranging, call Installation Support

for escalation; the test is FAILED.

If progress indicators are stuck at Network Entry, DHCP, Undefined, or Software

Download:

1. Text displays Network Entry, DHCP, or undefined:

a. Restart this test at step 5

b. If the progress indicators all display green in the restarted test and the status text

displays 'Online'; the test is PASSED

c. If the restarted test halts at Network Entry, DHCP or undefined, call Installation

Support for escalation; test is FAILED.

2. Text displays Software Download:

a. Allow download to complete (allow at least 30 minutes)

b. If download doesn’t complete, restart this test at step 5

c. If the progress indicators all display green in the restarted test and the status text

displays 'Online'; the test is PASSED

d. If the restarted test halts at Software Download, call Installation Support for

escalation; test is FAILED.

21.

Use the results of this test to determine the next step based on the checklist.

Andere Handbücher für SurfBeam 2

Inhaltsverzeichnis

Andere ViaSat Modem Handbücher

ViaSat

ViaSat SurfBeam Bedienungsanleitung

ViaSat

ViaSat RM5111 Bedienungsanleitung

ViaSat

ViaSat SurfBeam 2 RM4100 1-IFL Bedienungsanleitung

ViaSat

ViaSat SurfBeam 2 Bedienungsanleitung

ViaSat

ViaSat SurfBeam 2 Bedienungsanleitung

ViaSat

ViaSat surfbeam SM-1000 Bedienungsanleitung

ViaSat

ViaSat SurfBeam Bedienerhandbuch

ViaSat

ViaSat MEOLink Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung