Viatom Checkme Lite Bedienungsanleitung

制作工艺：

封面:157g铜版纸，过哑胶，彩色；

内页: 80g书写纸，黑白

胶装

尺寸：110*165mm

此页不印刷

Checkme Lite Health Monitor

Checkme Lite Health Monitor User’s Manual

Warnings and CautionaryAdvices



We recommend not to use this device if you have a pacemaker or other

implanted devices. Follow the advice given by your doctor, ifapplicable.



Do not use this device with a defibrillator.



Do not use this device during MRI examination.



Never submerge the device in water or other liquids. Do not clean the device with

acetone or other volatile solutions.



Do not drop this device or subject it to strong impact.



Do not place this device in pressure vessels or gas sterilization device.



Do not dismantle the device, as this could cause damage or malfunctions or

impede the operation of the device.



This device is not intended for use by people (including children) with restricted

physical, sensory or mental skills or a lack of experience and/or a lack of

knowledge, unless they are supervised by a person who has responsibility for

their safety or they receive instructions from this person on how to use the

device.



This device displays changes in the heart rhythm and blood oxygenation etc.

which may have various different causes. These may be harmless, but may also be

triggered by illnesses or diseases of differing degree of severity. Please consult a

medical specialist if you believe you may have an illness or disease.



Do not self-diagnose or self-medicate on the basis of this device without

consulting your doctor. In particular, do not start taking any new medication or

change the type and/or dosage of any existing medication without prior approval.



The device has no alarms and will not sound if the measurement reading is too

low or too high.

About Checkme

1.1

Intended Use

The Checkme Lite health monitor is intended to be used for measuring, displaying,

storing and reviewing of multiple physiological parameters including ECG and pulse

oxygen saturation (SpO2) in home or healthcare facilities environment.

ECG is intended for use with adult.

The data and results provided by this device are for pre-check screening purpose only

and cannot be directly used for diagnostic or treatment.

1.2

Outline

Touch Screen

Internal SpO2sensor

Micro-D connector

It connects with mirco-D cable for charging.

Home button



When the monitor is off, press this button to power it on.



When the monitor is on, press and hold it for 2 seconds to turn it off.



During operation, press this button will switch to Main Screen or return to upper

menu.

ECG right electrode

(Put right thumb on it.)

Speaker

ECG left electrode

(Put it to your left palm, left abdomen or left knee.)

Neck stripe hole

ECG back electrode

(Put right forefinger or middle finger on it.)

1.3

Main Screen

The Main Screen is shown as below.

Press an icon in the Main Screen will start a measurement, activate a function, or

open corresponding menu.

The device will enter Main Screen when:



No operation is detected for 60 seconds in result screen, the device will

automatically switch to Main Screen.



Pressing the Home button in other screen interface.

You can change the sound volume by taping the button on the left of the

screen, then tap the <Volume> area. Or you can also go to the Setting menu to change

it.

1.4

Symbols

Symbol

Description

Manufacturer

Date of manufacture

Serial number

Indicates a medical device that is not to be disposed of as unsorted

municipal waste.

Follow Instructions for Use.

Type BF Applied Part

No alarm system

MRI unsafe. Presents hazards in all MR environments as device

contains strongly ferromagnetic materials.

IP22

Resistant to liquid ingress

CE marking

Authorized representative in the European community

UKCA marking

Authorized Representative in the United Kingdom

This product complies with the rules and regulations of the Federal

Communication Commission.

Non-ionizing radiation

Our products and packaging can be recycled, don't throw them away!

Find where to drop them off on the www.quefairedemesdechets.fr

site (Only applicable for French market).

This product complies with verpackG.

Getting Started

2.1

Power On/Off

Press the Home button to power on the device. Press and hold Home button for 2

seconds to power off thedevice.

2.2

Initial Settings

The first time when the Checkme is powered on, you can set up your Checkme step by

step. You can also change the settings in the <Settings> menu.

Using Checkme

3.1

Prior to Use Before using ECG

Before using Daily Check or ECG Recorder function, pay attention to the following

points in order to obtain precise measurements.



If your skin or hands are dry, moisten them before taking the measurement.



During the measurement, do not touch your body with the hand with which you

are taking the measurement.



Please note that there must be no skin contact between your right and left hand.

Otherwise, the measurement cannot be taken correctly.



Stay still during the measurement, do not speak and move.



If possible, take the measurement when sitting instead of standing.

Before using Oximeter

Before using Daily Check and Oximeter function, pay attention to the following points

in order to obtain precise measurements.



The finger inserted in SpO2sensor must be clean.



Any of the following conditions may cause inaccurate measurements, including

but not limited to:

Flickering or very bright light;

Poor blood circulation;

Low hemoglobin;

Hypotension, severe vasoconstriction, severe anemia or hypothermia;

Nail polish, artificial nails;

Any tests recently performed on you that required an injection of

intravascular dyes.



The Oximeter may not work if you have poor circulation. Rub your finger to

increase circulation, or place the SpO2sensor on another finger.



The Oximeter measures oxygen saturation of functional hemoglobin. High levels

of dysfunctional hemoglobin (caused by sickle cell anemia, carbon monoxide,

etc.) could affect the accuracy of the measurements.



The pleth waveform displayed on the device is normalized.

Warnings and Cautionary Advices



Limit finger movement as much as possible when using the Daily Check or

Oximeter, which might result in incorrect reading or analysis.

3.2

Daily Check

About Daily Check

Warnings and Cautionary Advices



To ensure better tracking of your health status, it is strongly suggested that

every Daily Check measurement is made at the same time period when your

body is in the relative same situation. E.g., every morning when get up, or every

night before go to bed.

Daily Check measurement is a function that combines the measuring of ECG

(Electrocardiograph) waveform, HR (heart rate), SpO2 (blood oxygenation) and PI (Pulse

Index). It takes only 20 seconds to collect your vital signs before giving results.

Using Daily Check

Tostart a Daily Check, follow the steps as below.

Tap the <Daily Check> icon in the

middle of the Main screen.

Hold the device according to the

instruction, keep the device at the same level as your heart, and keep stable

posture and stay calm. Don’t exert too much pressure on the ECG electrode,

which may result in EMG (electromyograph) interference. Just hold gently and

ensure good contact with the ECG electrode. Do not exert pressure on the finger

that put in the SpO2 sensor. Just fit it inside but gently to ensure good blood

perfusion.

(1)

Put the right forefinger into the built-in SpO2sensor. Use the finger nail to

(1)

(4)

(2)

(3)

squeeze the edge of the SpO2sensor cover, then move in upward to the left

to raise it up as shown below.

(2)

Press the right thumb on the right electrode.

(3)

Press the right middle finger on the back

electrode.

(4)

Press the left electrode to the left palm.

Once the device detects stable waveform, it will

automatically start the measurement. The

countdown bar moves from left to right.

When the bar is fully filled, the device will analysis your data, and then show the

measurement result.

3.3

ECG Recorder

Different methods of taking the ECG measurement are available on Checkme. The ECG

recorder offers two different methods to measuring ECG:



Lead I: right hand to left hand



Lead II: right hand to left abdomen or left knee

Please keep stable posture and stay calm during the measurement. Movements may

result in interference and incorrect readings or analysis result.

Measuring without cable

Tostart an ECG Recorder measurement without cable,

If the device is power off, press the Home button.

In the Main Screen, tap the <ECG Recorder> icon.

Choose the method A or B.

Follow the instruction according to the mode you

selected.



Press the right thumb on the right electrode;



Press the right forefinger on the back electrode;



For Lead I, press the left electrode to the left palm;



For Lead II, press the left electrode to the left lowe

abdomen;

Do not press the device too firmly against your skin, which may

result in EMG ( electromyography ) interference. After you finish the above

steps, hold the device stably and stay calm.

Once the device detects stable waveform, it will automatically start the

measurement. The countdown bar moves from left to right.

When the bar if fully filled, the device will analysis your data, and then show the

measurement result.

Measuring with Cable

Tostart an ECG Recorder measurement with cable,

If the device is power off, press the Home button.

In the Main Screen, tap the <ECG Recorder> icon.

Choose the method C or D.

Follow the instructions to connect the ECG cable and place the ECG electrodes.



Sit down or stand, stay calm;



Palms facing up, place an electrode in the middle of right wrist;



For method C, place another electrode in the middle of left wrist;



For method D, place another electrode in the left lower abdomen;

The display will then show your ECG waveform.

The device will monitor your ECG continuously, however no data will be saved

until you press the button.

Press the button to start collecting your ECG data. The countdown bar moves

from left to right.

When the bar is fully filled, the device will analysis your data, and then show the

measurement result.

3.4

Oximeter

The Checkme Health Monitor measures the amount of oxygen in your blood (SpO2),

your pulse rate (PR) and pulse index (PI). The oxygen saturation (SpO2) is measured and

displayed as a percentage of full capacity.

Measuring without cable

Tostart a Oximeter measurement without cable,

If the device is power off, press the home button.

In the Main Screen, tap the “Pulse Oximeter” icon.

Insert the forefinger into the built-in SpO2sensor as shown below. Relax your

Andere Handbücher für Checkme Lite

Inhaltsverzeichnis

Andere Viatom Monitor Handbücher

Viatom

Viatom Checkme Lite Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung