Viavi E4100 Series Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS-2000 Modular Test Set

E4100 OTDR Module Optical Light Source option

This procedure describes how to use an E4100-series OTDR module as an Optical Light Source (OLS).

If optioned, the OTDR module can operate as an OLS or Optical Power Meter, but not both at the same

time. Note: the E41PM built-in power meter can be used at the same time as the Light Source options.

Equipment Requirements:

•T-BERD/MTS-2000 equipped with the

following:

oFiber Optics Software Release V17.30

or greater

oE4100 Series OTDR Module

oE41OTDRLS Light Source option

•Fiber optic cleaning and inspection tools

•Launch Cable (patch cord) with

connectors matching the OTDR port and

Fiber Under Test

•Optical Coupler to connect Launch Cable

to Fiber Under Test

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Type of Fiber (Multimode or Single Mode)

•Type of Connectors (SC UPC, SC APC, LC UPC, etc.)

•Wavelength(s) to be tested (850nm, 1300nm, 1310nm, 1550nm, etc.)

Fiber Inspection Guidelines:

•Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OTDR Port,

Launch Cable, bulkhead connectors,

patch cords, etc.)

•Focus the fiber on the screen. If dirty,

clean the connector.

•If it appears clean, run inspection test.

•If it fails, clean the fiber and re-run

inspection test. Repeat until it passes.

Figure 2: Inspect Before You Connect (IBYC)

VIAVI Solutions

Connect to Fiber Under Test (FUT):

All fibers and connectors should be inspected

and clean prior to connection, as described on

page 1. The Light Source may be connected to

the FUT via an optical patch panel (OPP) or an

optical coupler:

1. If the interface to the FUT is a patch

cord, connect the patch cord to an

optical coupler with the same connector

type.

2. Inspect the FUT connected to the

coupler or OPP.

3. Inspect the other fiber end face of the

Launch Cable.

4. Connect the Launch Cable to the coupler or

OPP.

Figure 3: Connecting the Launch Cable to the FUT with a coupler

Figure 4: Connecting the Launch Cable to an OPP

Operate the Light Source:

1. Press the Power button to start the test set.

2. Press the Home button to display the Home view with the SOURCE icon(s).

Figure 5. Home View.

3. Tap the desired SOURCE icon until it is yellow and highlighted . The Results view

will be shown with Light Source settings in the box labeled Source on Module.

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Figure 6. Results View

4. Tap the Mode soft key to select CW (Continuous Wave).

5. Press the Start/Stop button to turn the laser on. The laser warning symbol will be displayed.

6. Tap the Wavelength soft key to select the desired Output Wavelength (850nm, 1300nm, 1310nm,

1550nm, etc.)

7. Repeat Step 6 for all wavelengths to be tested.

8. At the conclusion of the test, tap the Start/Stop button to turn the laser off. Disconnect the Launch

Cable from the fiber under test. Do not disconnect the Launch Cable from the OTDR port or power off the T-

BERD/MTS-2000 until all testing is complete.

Inhaltsverzeichnis

Andere Viavi Steuereinheit Handbücher

Viavi

Viavi MTS/T-BERD TB8000e V2 Technisches Handbuch

Viavi

Viavi mA-3A01 Bedienungsanleitung

Viavi

Viavi SPA06MA-O R005 Bedienungsanleitung

Viavi

Viavi 8100 V2 Series Bedienungsanleitung

Viavi

Viavi SCU-1800 Bedienungsanleitung

Viavi

Viavi OSA-4100 Bedienungsanleitung

Viavi

Viavi COSA-4055 Bedienungsanleitung

Viavi

Viavi mA-3011 Bedienungsanleitung

Viavi

Viavi MTS/T-BERD TB6000A V2 Technisches Handbuch

Viavi

Viavi MTS/T-BERD TB6000A V1 Technisches Handbuch

Viavi

Viavi mA-3011 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS- 2000V2 Bedienungsanleitung

Viavi

Viavi MSAM Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi ODM V2 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung