Viavi T-BERD 5800 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS-5800 Modular Test Set

E4100 OTDR Module Optical Light Source option

This procedure describes how to use an E4100-series OTDR module as an Optical Light Source (OLS). If

optioned, the OTDR module can operate as an OLS or Optical Power Meter, but not both at the same

time.

Equipment Requirements:

•T-BERD/MTS-5800 equipped with the

following:

oFiber Optics Software Release V17.22

or greater

oE4100 Series OTDR Module

oE41OTDRLS Light Source option

•Fiber optic cleaning and inspection tools

•Launch Cable (patch cord) with

connectors matching the OTDR port and

Fiber Under Test

•Optical Coupler to connect Launch Cable

to Fiber Under Test

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Type of Fiber (Multimode or Single Mode)

•Type of Connectors (SC UPC, SC APC, LC UPC, etc.)

•Wavelength(s) to be tested (850nm, 1300nm, 1310nm, 1550nm, etc.)

Fiber Inspection Guidelines:

•Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OTDR Port,

Launch Cable, bulkhead connectors,

patch cords, etc.)

•Focus the fiber on the screen. If dirty,

clean the connector.

•If it appears clean, run inspection test.

•If it fails, clean the fiber and re-run

inspection test. Repeat until it passes.

Figure 2: Inspect Before You Connect (IBYC)

VIAVI Solutions

Connect to Fiber Under Test (FUT):

All fibers and connectors should be inspected

and clean prior to connection, as described on

page 1. The Light Source may be connected to

the FUT via an optical patch panel (OPP) or an

optical coupler:

1. If the interface to the FUT is a patch

cord, connect the patch cord to an

optical coupler with the same connector

type.

2. Inspect the FUT connected to the

coupler or OPP.

3. Inspect the other fiber end face of the

Launch Cable.

4. Connect the Launch Cable to the coupler or

OPP.

Figure 3: Connecting the Launch Cable to the FUT with a coupler

Figure 4: Connecting the Launch Cable to an OPP

Operate the Light Source

1. Press the Power button to turn on the T-BERD/MTS-5800.

2. Tap the Fiber Optics icon in the Status Bar at the top of the T-BERD/MTS-5800.

3. Tap the Home icon to display the Home screen, showing the SOURCE icon(s).

Figure 5: Home View

4. Tap the desired SOURCE icon until it is yellow and highlighted . The Results view

will be shown with Light Source settings in the box labeled Source on Module.

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Figure 6: Results View

5. Tap the Mode soft key to select CW (Continuous Wave).

6. Tap the Start/Stop key to turn the laser on. The laser warning symbol will be

displayed.

7. Tap the Wavelength soft key to select the desired Output Wavelength (850nm,

1300nm, 1310nm, 1550nm, etc.)

8. Repeat Step 7 for all wavelengths to be tested.

9. At the conclusion of the test, tap the Start/Stop key to turn the laser off. Disconnect the

Launch Cable from the fiber under test. Do not disconnect the Launch Cable from the OTDR

port or power off the T-BERD/MTS-5800 until all testing is complete.

Andere Handbücher für T-BERD 5800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi FIT-82P03-PRO Bedienungsanleitung

Viavi

Viavi OneExpert ONX CATV Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi 4100 Series Stücklistenhandbuch

Viavi

Viavi ALT-9000 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi OLP-88 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800-100G Stücklistenhandbuch

Viavi

Viavi T-BERD 5800 Stücklistenhandbuch

Viavi

Viavi FCOMP/-PRO T-BERD/MTS-2000V2 Bedienungsanleitung

Viavi

Viavi Parent Guide Bedienungsanleitung

Viavi

Viavi SmartOTDR 100 Bedienungsanleitung

Viavi

Viavi SmartOTDR 100 Bedienungsanleitung

Viavi

Viavi ComXpert CX100 Bedienungsanleitung

Viavi

Viavi SmartOTDR Mainframe Bedienungsanleitung

Viavi

Viavi OneAdvisor-1000 Bedienungsanleitung

Viavi

Viavi CT-X Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi MTS 2000 Bedienungsanleitung

Viavi

Viavi OLP-88 Bedienungsanleitung

Viavi

Viavi FBP-HD4iP Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung