Viavi T-BERD 6000A V2 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD 6000Av2 Network Tester

Datacom Bit Error Rate Testing (BERT)

This quick card describes how to configure the T-BERD 6000A as Data Terminal Equipment (DTE) and

run a Bit Error Rate Test on a Datacom interface using typical configuration settings. Please refer to

the MSAM Data Communication and Diphase Testing Manual for an explanation of all settings.

Equipment Requirements:

•T-BERD 6000Av2 equipped with the following:

oBERT software release V26.3 or greater

oTest options:

▪High Speed Datacom test option

(VIAVI Part# CTHSDATA)

•Multi-Services Application Module

(VIAVI Part# C1010V2)

•Datacom Physical Interface Module (PIM)

(VIAVI Part# CPHSDATAV2)

•One of the following Datacom cables to connect the

Datacom PIM to the line under test:

oRS-232/V.24, MIL-188c, EIA-530 Cable

(VIAVI Part# CB-44385)

oRS-449/V.36 Cable (VIAVI Part# CB-44388)

oV.35 Cable (VIAVI Part# CB-44390)

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Interface (RS-232/V.24, MIL-188c, EIA-530, RS-449/V.36, or V.35)

•Signal Mode (Balanced or Unbalanced)

•Timing Mode (Synchronous or Asynchronous)

•Rx Timing Source (Internal, Interface, or Recovered)

•Tx Timing Source (Internal or Interface)

•Out of Band Flow Control (On or Off)

•Test Patterns(s)

•BER Pass/Fail Threshold

Connect to Line Under Test:

•Connect the desired Datacom cable to the Datacom PIM.

•Use the connector labeled “To DCE”to connect to the line under test.

VIAVI Solutions

Launch and Configure Test:

1. Press the Power button to turn on the

test set.

2. Press the Home button and tap the

BERT icon to launch the MSAM.

3. Using the Select Test menu or Quick

Launch menu, launch the HS Datacom►

HS Datacom BERT►Terminate test.

Figure 2: Home screen

Figure 3: Launch Screen

4. Tap the tools menu and select

5. Press to continue.

Figure 4: Reset Test to Defaults

VIAVI Solutions

6. Press the Setup Soft Key, , on the top right side of the screen. Select the indicated tabs and

configure your test as follows. Leave all other values at default, unless specified in the work order.

Folder

Option

Value(s)

Interface

RS-232/V.24, EIA-530, RS-449/V.36, etc.

Equipment Type

DTE

Signal Mode

Balanced or Unbalanced

Timing

Timing Mode

Synchronous or Asynchronous

Rx Timing Source

Recovered or Interface (RT). If unknown, select

Interface (RT).

Tx Timing Source

Internal (Synth), External (BNC), or Interface (ST).

If unknown, select Interface (ST) for Synchronous timing,

select Internal (Synth) for Asynchronous timing.

Synthesizer Frequency

Enter frequency in kHz; i.e. 9.6 kHz for 9600 bps.

Pattern

Pattern Mode

ANSI

Pattern

Enter the first Pattern in your test plan (QBF, QRSS, etc.)

7. Press the Results Soft Key to view the

Test Results screen.

8. Tap the Signal Lead tab at the bottom of

the screen and tap the RTS and DTR

buttons.

9. Press the Restart soft key .

Figure 5: Test Results Screen, Signal Leads

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest

you, visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

10. Using the drop-down menus, select

“HS Datacom/BERT” for the right results

display.

11. Allow the test to run for desired duration

and verify the following:

•Summary LED is green.

•Pattern Sync LED is green.

•Bit Error Rate result does not exceed

your required threshold. (0.00E+00 if

pass/fail threshold unknown)

Figure 6: Test Results Screen, HS Datacom/BERT

12. In the T-BERD’s Quick Config menu,

change “Pattern” to the next value in the

test plan.

13. Press the Restart soft key to reset

results.

14. Allow test to run for desired duration and

verify the following:

•Pattern Sync LED is green.

•Bit Error Rate does not exceed your

required threshold. (0.00E+00 if

pass/fail threshold unknown)

Figure 7: Test Plan

15. Repeat steps 12 through 14 for all Patterns in the test plan. Patterns may include:

•QRSS

•QBF

•R-Trip Delay

Simulates live traffic

Quick Brown Fox message

Measures Round Trip Delay (RTD) instead of Bit Errors (RTD values

are shown instead of BER in the “Payload/BERT” results display)

Andere Handbücher für T-BERD 6000A V2

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi T-BERD/MTS 4000 V2 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Installationsanleitung

Viavi

Viavi T-BERD/MTS 8000 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Installationsanleitung

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi FBP-HD4iP Bedienungsanleitung

Viavi

Viavi SmartClass Fiber OLS-85 Bedienungsanleitung

Viavi

Viavi 3550 Bedienungsanleitung

Viavi

Viavi 4100 Series Stücklistenhandbuch

Viavi

Viavi T-BERD 6000A V2 Bedienungsanleitung

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-4000 v2 Stücklistenhandbuch

Viavi

Viavi OneExpert DSL Bedienungsanleitung

Viavi

Viavi OneExpert ONX CATV Bedienungsanleitung

Viavi

Viavi 8800SX Bedienungsanleitung

Viavi

Viavi FIT-82P03-PRO Bedienungsanleitung

Viavi

Viavi ComXpert CX100 Bedienungsanleitung

Viavi

Viavi OneExpert DSL Bedienungsanleitung

Viavi

Viavi FBP-HD4i Bedienungsanleitung

Viavi

Viavi ONX 580 Bedienungsanleitung

Viavi

Viavi ALT-8000 Stücklistenhandbuch

Viavi

Viavi OLA-54 Bedienungsanleitung

Viavi

Viavi SmartClass Fiber OLTS-85 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung