Viavi T-BERD MTS 5800 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS-5800 Network Tester

Ethernet Layer 3 Multicast Traffic Generation

This document outlines how to use the T-BERD 5800 to generate IPv4 Multicast Traffic. A second T-

BERD/MTS 5800 or compatible device should be used at the far-end of the line under test to analyze

the multicast traffic and measure key performance indicators (KPIs). Multicast traffic analysis and

IGMP group membership registration is covered in a separate Quick Card.

Equipment Requirements:

•T-BERD/MTS-5800 equipped with the

following:

oBERT software release V27.2 or greater

oC510M1GE Gigabit Ethernet test option

oSFP, QSFP, or CFP4 optical transceiver

to match the line under test

•Patch Cables to match the T-BERD/MTS

optics and the line under test

•Fiber optic inspection microscope (VIAVI

P5000i or FiberChek Probe)

•Fiber Optic Cleaning supplies

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Physical Interface (10/100/1000BASE-T, 1000BASE-LX, 10GBASE-LR, 100GBASE-LR4, etc.)

•Auto Negotiation settings of the port under test

•VLAN ID, if VLAN tagging is used

•IP Address Parameters (DHCP or Static, Source IP, Default Gateway, Subnet Mask)

•Destination Multicast Group IP Address for test traffic.

•Packet size and Transmit rate for test traffic.

Fiber Inspection Guidelines:

•All fiber end-faces must be clean and pass

an inspection test prior to connection.

•Use the VIAVI P5000i, FiberChek Probe, or

Sidewinder microscope to inspect both

sides of every connection being used (SFP

Port, bulkhead connectors, patch cords,

etc.)

Figure 2: Inspect Before You Connect

VIAVI Solutions

Connect to Fiber Under Test (FUT):

1. For copper 10/100/1000BASE-T interface

testing with the T-BERD/MTS 5800v2,

connect the Port 1 10/100/1000 RJ-45 jack

to the port under test using CAT 5E or

better cable.

2. For copper 10/100/1000BASE-T interface

testing with the T-BERD/MTS 5800-100G,

insert a copper SFP into the Port 1

SFP+/SFP28 slot and connect to the port

under test using CAT 5E or better cable.

Figure 3: T-BERD 5800v2 Dual Port mainframe

3. For optical interfaces:

•Insert SFP compatible with your

physical interface into the Port 1 slot

on the top of T-BERD.

•Inspect and, if necessary, clean all

fibers and bulkheads, as described on

page 1.

•Connect the SFP to the port under test

using a Single Mode or Multimode

jumper cable compatible with the

interface under test.

Figure 4: T-BERD 5800-100G mainframe

Launch and Configure Test:

1. Press the Power button to turn on the test set and view the startup screen.

2. Using the Select Test menu, Quick Launch menu, or Job Manager, launch an Ethernet, Layer 3

Traffic, IPv4, Terminate test on port 1 for the desire physical interface. For example:

Ethernet►10/100/1000►Layer 3 Traffic►IPv4►P1 Terminate.

Figure 5: Startup Screen

VIAVI Solutions

3. If the test is not in the default settings, tap the Tools icon and select .

Tap and wait for test to reconfigure.

4. Tap the Setup Soft Key to display the Interface settings tab.

5. If you are testing a 10/100/1000 Electrical or 1GigE Optical tests with auto negotiation

disabled, select the Physical Layer tab and configure settings to match the Ethernet port under

test.

6. If the network under test uses VLAN tagging, select the Ethernet settings tab, set Encapsulation

to VLAN, tap [VLAN] and enter your VLAN ID.

7. Select the IP settings tab.

8. Select the desired packet size in the Packet Length (bytes) setting.

9. Select the Source/Destination Addresses field.

a. Enter the Source IP, Default Gateway and Subnet Mask values.

b. Set Destination IP to the desired Multicast Group IP address to transmit traffic to; for

example, 224.0.0.120.

Figure 6: IP Settings

10. Select the Traffic settings tab. Set Load Unit to Bit Rate and set Load to the desired traffic rate

for the Multicast traffic.

11. Tap the Results Soft Key, to view the Results screen.

12. If using the optical test port on T-BERD/MTS press the Laser Off button at the bottom of the

screen to turn on the port laser. The button will turn yellow and be relabeled Laser On.

13. Sync Acquired and Link Active LEDs are green. A green Signal Present LED ● indicates the

T-BERD/MTS is receiving an optical signal from the port under test. Green Sync Acquired and

Link Active LEDs indicate that the T-BERD/MTS has successfully connected to the port under

test and the link is active.

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Figure 7: Results Screen

14. Tap in the Action tab at the bottom of the screen to start transmitting Multicast traffic.

The button will turn yellow and be relabeled .

15. Tap the Restart Soft Key , on the right side of the screen.

16. You can observe the Multicast traffic transmit rate in the Summary -> SLA/KPI results view.

Figure 8: Summary Results

Andere Handbücher für T-BERD MTS 5800

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi OneAdvisor ONA-1000 400G Technisches Handbuch

Viavi

Viavi T-BERD/MTS 4000 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi ONX-220 Bedienungsanleitung

Viavi

Viavi 8000 V2 Platform Bedienungsanleitung

Viavi

Viavi T-BERD MTS-580 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 8000 Stücklistenhandbuch

Viavi

Viavi FIT-82P03 Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-800 Stücklistenhandbuch

Viavi

Viavi OneExpert DSL Bedienungsanleitung

Viavi

Viavi 3900 Series Bedienungsanleitung

Viavi

Viavi T-BIRD-4000 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 2000 Bedienungsanleitung

Viavi

Viavi SmartOTDR 100 Bedienungsanleitung

Viavi

Viavi OneExpert CATV Bedienungsanleitung

Viavi

Viavi ONX 580 Bedienungsanleitung

Viavi

Viavi ALT-9000 Stücklistenhandbuch

Viavi

Viavi OLP-88 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi T-BERD 5800 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung