Victa MV 1200 Bedienungsanleitung

1
IMPORTANT
READ THIS BOOK CAREFULLY BEFORE OPERATING THIS MACHINE
Not for
Reproduction

MINI-VAC
CONTENTS
Features......................................................................................1
Safety instructions ............................................................................2
Assembling your Mini Vac .....................................................................4
Using your Mini Vac ...........................................................................6
Maintenance & helpful tips ....................................................................8
Warranty ....................................................................................10
Not for
Reproduction

1
Powerful 1400 Watt
electric motor
ON/OFF switch
Ergonomic handle
Easy to remove
lightweight
consumable bag
Easy to manoeuvre
wheel design
Extra wide low
clearance vacuum inlet
FEATURES
Adjustable operating
height
Cooling Air inlets
Not for
Reproduction

2
MINI-VAC
SAFETY INSTRUCTIONS
Caution
Read the instructions carefully. Be familiar with the controls and proper use of
the appliance.
Ensure that the power point is switched o and the plug removed before you
attempt any maintenance, adjustment or cleaning of your Victa Mini Vac. Before
using check the supply and extension cords for wear or damage. Do not use the
appliance if the cord is damaged or worn.
Keep bystanders away. The Victa Mini Vac should not be used any closer than 15m
to other people. Never operate while children or pets are nearby.
Wear safety glasses or goggles when operating the Victa Mini Vac. Use a face or
dust mask whenever the conditions are dusty. Hearing protection should always
be used.
Don’t use your Victa Mini Vac in wet conditions. Don’t leave or use it in the rain. Do
not vacuum water, liquids or excessively damp debris.
IT IS ESSENTIAL TO READ AND UNDERSTAND THESE
INSTRUCTIONS BEFORE USING MACHINE
Not for
Reproduction

3
t /FWFSBMMPXQFPQMFVOGBNJMJBSXJUIUIFTFJOTUSVDUJPOTUPVTFZPVS.JOJ7BD
t /FWFSPQFSBUFZPVS7JDUB.JOJ7BDXJUIPVUUIFCBHQSPQFSMZöUUFE*GUIFCBHJT
OPUQSPQFSMZöUUFEUIFNBDIJOFNBZNPWFGPSXBSEPSQSPKFDUQBSUJDMFTPVUPGUIF
discharge chute. These particles may cause injury.
t .BLFTVSFZPVSQPXFSQPJOUJTQSPQFSMZFBSUIFEBOEUIBUZPVSFYUFOTJPODPSE
complies to electrical standards, is in good condition and is weather proof.
t )BWFZPVS7JDUB.JOJ7BDJOTQFDUFEBOETFSWJDFEBUBOBQQSPWFETFSWJDFDFOUSFPS
agent if:
o The motor, cord or switch needs repair or maintenance.
o It is running abnormally or eratically.
o The switch action is not positive or the motor emits burning odours or sparks.
o It is dropped or damaged in any way.
t 5IJTBQQMJBODFJTOPUJOUFOEFEGPSVTFCZZPVOHDIJMESFOPSJOöSNQFSTPOTVOMFTT
they have been adequately supervised by a responsible person to ensure that they
use the appliance safely.
t %POPUVTFBSPVOEBTXJNNJOHQPPMXIJMFQFPQMFBSFTXJNNJOH*GUIFNBDIJOF
falls into the water there is the danger of electrocution.
t 8IJMFVTJOHUIF.JOJ7BDBMXBZTXFBSTVCTUBOUJBMGPPUXFBSMPOHUSPVTFST
t %POPUXFBSMPPTFDMPUIJOHPSKFXFMMFSZUIBUDBOCFESBXOJOUPUIFBJSJOMFU,FFQ
long hair away from the air inlets.
t /FWFSWBDVVNöTIJOHMJOFTUSJOHQMBTUJDCBHTPSTJNJMBSNBUFSJBMJOUPUIFVOJUBT
tangling with the impeller may cause the motor to overload and stall. If this occurs
switch the Mini Vac o. Do not allow the Mini Vac to remain switched on in the
stalled or overloaded condition.
Note: Do not use the Mini Vac for anything out side of its intended use.
See a authorised dealer for further assistance if required.
t "MXBZTPQFSBUFUIFVOJUJOBOVQSJHIUQPTJUJPO%POPUPQFSBUFUIFVOJUXIFO
tipped on its side or upturned.
t "MXBZTVTFBOFYUFOTJPODPSEXJUIIFBWZEVUZJOTVMBUJPOUIBUJTXFBUIFSQSPPGBOE
designed for outdoor use. Nominal cross-sectional area of the conductors should
not be less than 1.0mm2.
Not for
Reproduction

4
MINI-VAC
ASSEMBLING
YOUR MINI-VAC
Mini Vac unit
Bag
Unassembled
handle
Not for
Reproduction

5
Bag Hook
FITTING THE HANDLE
1. Fit loose bolt through lower tube. Fit
center tube over bolt, then screw on
hand knob.
2. Fit handle to center tube and screw on
other hand knob.
)BOHCBHGSPNIBOEMFCZöUUJOHFZFMFU
over handle hook.
ATTACHING THE VACUUM BAG
1. Fit“twist-and-seal” bag attachment to
vacuum discharge.
2. Twist bag attachment handle to upright
position
ON
OFF
DO NOT FORCE
HANDLE
Not for
Reproduction

6
MINI-VAC
USING YOUR
MINI-VAC
BEFORE YOU START
t &OTVSFUIBUUIFIBOEMFIBTCFFODPSSFDUMZ
öUUFEBOEJTöSNMZGBTUFOFEUPUIFNBDIJOF
(see assembly instructions) P5.
t "MXBZTFOTVSFUIBUUIFWBDVVNCBHJT
öUUFEUPUIF.JOJ7BDCFGPSFTXJUDIJOHPO
(see assembly instructions) P5.
t Connect to an extension cord. Loop the
extension cord through the handle and
around the cord restraint as shown.
t "MXBZTEJSFDUUIFDPSEUPUIFSFBSBXBZ
from the appliance.
t *GBDPSECFDPNFTEBNBHFEEVSJOHVTF
disconnect the supply cord from the
mains immediately.
DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
t %POPUDBSSZUIFBQQMJBODFCZUIFDPSE
t %JTDPOOFDUUIFBQQMJBODFGSPNUIFNBJOT
supply.
- whenever you leave the machine;
- before clearing a blockage;
- before checking, cleaning or
working on the appliance;
- if the appliance starts to vibrate
abnormally.
t 0QFSBUFUIFBQQMJBODFPOMZJOEBZMJHIUPS
JOHPPEBSUJöDJBMMJHIU
t %POPUPWFSSFBDIBOELFFQZPVSCBMBODF
at all times.
t "MXBZTCFTVSFPGZPVSGPPUJOHPOTMPQFT
t 8BMLOFWFSSVO
t ,FFQ BMM DPPMJOH BJS JOMFUT DMFBS PG EFCSJT
It is recommended that the Mini Vac
should be connected to the mains through
a Residual Current Device (RCD) with a
tripping current of not more than 30 mA.
Always use a heavy duty extension cord.
t &OTVSFUIF.JOJ7BDJTTXJUDIFEPò
t 4XJUDIPOBUUIFIBOEMFo"MXBZTEPUIJT
from a standing position. Never while
kneeling or sitting next to the Mini Vac .
t i7BDwBXBZEFCSJTCZNPWJOHUIF.JOJ7BD
over the area to be cleared.
Cord Restraint
Not for
Reproduction

7
2. Unhook bag
EMPTYING THE VACUUM BAG
3. Unzip bag
4. Empty bag into
a rubbish bin
3. Unzip bag
1. Rotate “twist-and-seal”
collar to the OFF position
OFF
Note: Shake bag to empty contents.
Always wear eye protection when
cleaning the bag.
NOTE: ENSURE THE MINI VAC IS SWITCHED OFF!
Not for
Reproduction

8
MINI-VAC
MAINTENANCE
& HELPFUL TIPS
High
Setting
low
Setting
HEIGHT ADJUSTMENT
The Mini Vac has height adjustment
that is easy to change.
Note: Ensure your Mini Vac is switched
o before adjusting the operating
height.
t 'PSUIFIJHIIFJHIUTFUUJOHNPWF
the front wheels forward, so they are in
the slot closest to the vacuum inlet.
t 'PSUIFMPXIFJHIUTFUUJOHNPWFUIF
front wheels back, so they are in the slot
closest to the handle.
Not for
Reproduction
Inhaltsverzeichnis
Andere Victa Gebläse Handbücher




















