Viega Multiplex Trio E Bedienungsanleitung
for the operation of Multiplex Trio E by mobile end devices (APP)
Model Year built:
6146.224 from 06/2016
en_INT
Multiplex Trio E-WLAN module
Instructions for Use
Multiplex Trio E-WLAN module 2 from 15
Table of contents
1About these instructions for use 4
1.1 Target groups 4
1.2 Labelling of notes 4
1.3 About this translated version 5
2Product information 6
2.1 Safety advice 6
2.2 Intended use 6
2.3 Product description 7
2.3.1 Overview 7
2.3.2 Technical data 7
3Handling 8
3.1 Mounting instructions 8
3.2 Assembly 8
3.2.1 Installation situation Trio E or E2 8
3.2.2 Installation situation Trio E3 9
3.3 Commissioning 11
3.3.1 Establishing a connection with mobile end devices 11
3.4 Disposal 15
Table of contents
Multiplex Trio E-WLAN module 3 from 15
1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at
viega.com/legal
.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
nHeating and sanitary professionals and trained personnel
nOperators
nConsumers
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Multiplex Trio E-WLAN module 4 from 15
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, stand-
ards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.
About these instructions for use
Multiplex Trio E-WLAN module 5 from 15
2 Product information
2.1 Safety advice
DANGER!
Risk of electric shock
An electric shock can lead to burns and serious injury and
even death.
– Work on the electrics may only be carried out by trained
electricians.
– Switch off the mains voltage before opening the casing.
– Switch off the mains voltage before connecting the
power pack.
WARNING!
Risk of scalding from hot water
Excessively hot water can lead to severe scalding, espe-
cially in the case of children.
Take the following steps to avoid scalding:
– Do not allow children to play with the control elements
unsupervised.
– Disable the temperature safeguard in exceptional cases
only.
– Make sure that no one can come into contact with the
hot water before carrying out thermal disinfection.
WARNING!
Risk of injury due to control via remote access
Controlling the equipment via remote access is permissible
only if there are no persons standing in the direct operating
range.
2.2 Intended use
The WLAN module controls the Multiplex Trio E fittings by means of a
mobile end device (such as smartphone or tablet). The WLAN module is
easy to refit for already installed Multiplex Trio E fittings (art. no. 662295,
682972, 684655).
The installation is permissible for specialist companies only under com-
pliance with the applicable regulations.
Pay attention to the additional notes in the respective instructions for
use of the Multiplex Trio E.
Product information
Multiplex Trio E-WLAN module 6 from 15
2.3 Product description
2.3.1 Overview
2
1
3
Fig. 1: Overview
1 - WLAN module
2 - Connection socket
3 - Plug (display)
2.3.2 Technical data
Dimensions H x W x D 63 x 63 x 24 mm
Operating temperature min.–max. 0–60 °C
Rel. humidity min.-max. 5–95 %
Plug JST XHP6
Cable length 200 mm
Encryption WPA 2
Network WLAN (802.11 b/g/n)
IP Code IP 20
Protection class III
Power supply 6–15 V
Transmission frequency 2.4 Ghz
Material (casing) ABS
NOTICE!
Regularly update your browser and operating system.
Should you have any questions on compatibility, please
contact the Viega Service Center.
Product information
Multiplex Trio E-WLAN module 7 from 15
3 Handling
3.1 Mounting instructions
The WLAN module is mounted in different manners, depending on the
existing Multiplex Trio E-fitting:
nMultiplex Trio E and E2 (
ÄChapter 3.2.1 „Installation situation Trio E
or E2“ on page 8
)
nMultiplex Trio E3 (
ÄChapter 3.2.2 „Installation situation Trio E3“
on page 9
)
If the WLAN module is mounted together with the Multiplex Trio E fit-
ting, the assembly steps for the Multiplex Trio E fitting must be
observed as well.
Connect the existing connection cables in the following plugging order:
1 TLI A
2 TLI B
3 Motor
4 Display
5 BATTERY
6 15 V
7 ! 230-V connection
3.2 Assembly
3.2.1 Installation situation Trio E or E2
Use a Phillips-tip screwdriver to remove the two screws from the
casing, and lift off the cover.
Refitting an existing Multiplex Trio E fitting
Mounting the Multiplex Trio E fitting together with the WLAN module
Handling
Multiplex Trio E-WLAN module 8 from 15
Insert the WLAN module (cable outlet left-hand side) at an angle into
the gap between battery and power pack.
Plug the connection cable of the WLAN module into the slot with the
designation
„Display“
.
Replace the casing cover and use the Phillips-tip screwdriver to
tighten the two screws.
3.2.2 Installation situation Trio E3
PW: 1 23456 789 0
ON Prototy pe
SN 12345 678 90
PW: 123 4567890
ON Prot otype
SN 1234 567890
Handling
Multiplex Trio E-WLAN module 9 from 15
Use a Phillips-tip screwdriver to remove the two screws from the
casing, and lift off the cover.
Remove the plug at the
„Display“
slot.
Plug the removed display cable into the WLAN module.
Insert the WLAN module (cable outlet left-hand side) at an angle into
the gap between battery and power pack.
Handling
Multiplex Trio E-WLAN module 10 from 15
Andere Handbücher für Multiplex Trio E
1
Inhaltsverzeichnis
Andere Viega Steuereinheit Handbücher
Viega
Viega 2281.7 Bedienungsanleitung
Viega
Viega ProPress 22074 Merkblatt
Viega
Viega Grundfix 4987 Bedienungsanleitung
Viega
Viega 2337.5 Bedienungsanleitung
Viega
Viega 1247.4 Bedienungsanleitung
Viega
Viega Easytop 2275.10 Bedienungsanleitung
Viega
Viega PureFlow Crimp Zero Lead Merkblatt
Viega
Viega 2243.10 Bedienungsanleitung
Viega
Viega Easytop XL Series Bedienungsanleitung
Viega
Viega ManaBloc Merkblatt
Viega
Viega 2235.2 Bedienungsanleitung
Viega
Viega Grundfix Plus-Control Bedienungsanleitung
Viega
Viega 9690TW Bedienungsanleitung
Viega
Viega G2101 Bedienungsanleitung
Viega
Viega 8655.11 Bedienungsanleitung
Viega
Viega 8127.3 Bedienungsanleitung
Viega
Viega PureFlow Crimp Merkblatt
Viega
Viega 8310.0 Bedienungsanleitung
Viega
Viega 2275.2 Bedienungsanleitung
Viega
Viega 1252.1 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
