Viega Fonterra Smart Control Bedienungsanleitung

Year built:

from 11/2015

en_INT

Fonterra Smart Control

Instructions for Use

Fonterra Smart Control 2 from 115

Table of contents

1About these instructions for use 5

1.1 Target groups 5

1.2 Labelling of notes 5

1.3 Acronyms 6

1.4 About this translated version 6

2Product information 7

2.1 Standards and regulations 7

2.2 Safety advice 8

2.3 Intended use 8

2.4 Regulations / certificates 8

2.5 Product description 9

2.5.1 Functions and characteristics 9

2.5.2 Overview and description of component 10

2.5.3 Accessories 17

2.6 Technical data 23

2.6.1 Electronic system 23

2.6.2 Software / hardware 27

2.7 System requirements 27

2.7.1 Hardware 27

2.7.2 Software 28

2.8 Configuration levels 29

3Handling 31

3.1 Transport and storage 31

3.2 Assembly information 31

3.2.1 Preconditions for installation 31

3.2.2 Installation dimensions 32

3.3 Assembly 34

3.3.1 Assembly sequence 34

3.3.2 Mounting the temperature measuring points 34

3.3.3 Mounting the actuators 36

3.3.4 Mounting the basic unit 36

3.3.5 Mounting the actuator modules 43

3.3.6 Mounting the room thermostat 46

3.3.7 Mounting the radio amplifier 52

3.4 Commissioning 52

Table of contents

Fonterra Smart Control 3 from 115

3.4.1 Preconditions for commissioning 52

3.4.2 Configuration level 1 – Control via power level 54

3.4.3 Configuration level 2 – Control via room thermostat 55

3.4.4 Configuration level 3 – Operation of a base station in the

WLAN network 60

3.4.5 Configuration level 4 – Operating several base stations via

the Internet 65

3.4.6 Checking the functions 78

3.4.7 Resetting the factory settings – Reset 79

3.4.8 Operating conditions 81

3.5 Control 83

3.5.1 Room thermostat 83

3.5.2 Operating software 84

3.6 Faults 106

3.6.1 Fault alarms 106

3.7 Care and maintenance 109

3.7.1 Maintenance 109

3.7.2 Care 109

3.7.3 Replacing components 110

3.8 Disposal 115

Table of contents

Fonterra Smart Control 4 from 115

1 About these instructions for use

Trade mark rights exist for this document; for further information, go to

viega.com/legal.

1.1 Target groups

The information in this instruction manual is directed at the following

groups of people:

nHeating and sanitary professionals and trained personnel

nQualified electricians

nOperators

nConsumers

Individuals without the abovementioned training or qualification are not

permitted to mount, install and, if required, maintain this product. This

restriction does not extend to possible operating instructions.

The installation of Viega products must take place in accordance with

the general rules of engineering and the Viega instructions for use.

This manual must be handed over to the operator or user after the

assembly and commissioning of the product.

1.2 Labelling of notes

Warning and advisory texts are set aside from the remainder of the text

and are labelled with the relevant pictographs.

DANGER!

This symbol warns of possible life-threatening injury.

WARNING!

This symbol warns of possible serious injury.

CAUTION!

This symbol warns of possible injury.

NOTICE!

This symbol warns of possible damage to property.

About these instructions for use

Fonterra Smart Control 5 from 115

This symbol gives additional information and hints.

1.3 Acronyms

This documentation uses the following abbreviations:

WM Wall mounting

CC Concealed mounting

1.4 About this translated version

This instruction for use contains important information about the choice

of product or system, assembly and commissioning as well as intended

use and, if required, maintenance measures. The information about the

products, their properties and application technology are based on the

current standards in Europe (e. g. EN) and/or in Germany

(e. g. DIN/DVGW).

Some passages in the text may refer to technical codes in Europe/

Germany. These should serve as recommendations in the absence of

corresponding national regulations. The relevant national laws, stand‐

ards, regulations, directives and other technical provisions take priority

over the German/European directives specified in this manual: The

information herein is not binding for other countries and regions; as said

above, they should be understood as a recommendation.

About these instructions for use

Fonterra Smart Control 6 from 115

2 Product information

2.1 Standards and regulations

The following standards and regulations apply to Germany / Europe and

are provided as a support feature.

Regulations from section: Regulations / Certificates

Scope / Notice Regulations applicable in Ger‐

many

CE conformity of the electrical

components

EN 60730-1

nPart 1 – General requirements

nPart 2-9: Special requirements

in temperature-dependant reg‐

ulation and control systems

CE conformity of the electrical

components

EN 300220-1

Regulation on energy-saving heat

insulation and energy-saving

installation engineering

Energieeinsparverordnung (EnEV)

Household and similar electrical

appliances – Safety

(SRD) IEC 60335-1

Information technology equipment

– Radio disturbance characteris‐

tics

EN 55022

Regulations from section: Extension level 1 – Control via power level

Scope / Notice Regulations applicable in Ger‐

many

Control mode for secondary

rooms or rooms < 6 m2

Energieeinsparverordnung (EnEV)

Regulations from section: Disposal

Scope / Notice Regulations

Disposal of electronic compo‐

nents

WEEE-Richtlinie 2012/19/EU

Product information

Fonterra Smart Control 7 from 115

2.2 Safety advice

DANGER!

Danger due to electrical current

An electric shock can lead to burns and serious injury and

even death.

– Work on the electrics may only be carried out by trained

electricians.

– Switch off the mains voltage before carrying out work on

electrical parts.

NOTICE!

All cable connections must be made via plug connections,

their form should make them non-interchangeable.

The connection cables may not be extended.

The total length of the connection cable must not exceed

10 m.

2.3 Intended use

Fonterra Smart Control is an electronic single room regulation for

radiant heating and cooling systems with one or several manifolds. In

connection with radiant heating and cooling systems, the system can be

used within a control range of 5–30 °C also for cooling purposes. The

function is guaranteed for the combination with Fonterra manifolds

DN25.

Manifolds by other manufacturers are compatible if they comply with

the following specification:

nThreaded connection with euro cone and valve inserts –

M30 x 1.5 mm

nValve inserts – stroke 3.2 mm / resulting dimension 11.8 mm

nManifold outlets – minimum distance 45 mm

Use with electronic components by other manufacturers is not per‐

mitted.

2.4 Regulations / certificates

All components have a CE mark and comply with the applicable regula‐

tions, see

„Regulations from section: Regulations / Certificates“

on page 7.

Product information

Fonterra Smart Control 8 from 115

2.5 Product description

2.5.1 Functions and characteristics

Fonterra Smart Control is an electronic single room regulation for

radiant heating and cooling systems with one or several manifolds in a

control range of 5-30 °C.

The room temperatures can be set individually for each heating circuit

with power levels, via room thermostat control, or centrally via end

devices. Access to the parameters of individual casing units and to the

control of entire buildings via building master control systems is carried

out via password-protected WLAN or Internet connections.

The temperature data of the room thermostats, the flow sensor and the

return flow sensors are evaluated by measurement and used for the

individual temperature control of each heating circuit.

Benefits of the system:

nManual hydraulic calibration is no longer necessary and is replaced

by permanent hydraulic calibration via the system.

nThe control system compensates external interferences:

– Different pipe sizes, installation distances, heating circuit lengths

– Different screed heights, floor coverings, areas covered by rugs

or furniture etc.

– Fluctuating supply temperatures

– Outdoor temperatures, external heat sources

In keeping with the on-site requirements, Fonterra Smart Control can be

operated in four configuration levels:

nConfiguration level 1: Control via power level

The base station controls the actuators via a power level – no room

thermostat is installed.

nConfiguration level 2: Control via room thermostat

The base station controls the actuators via calibration of the target/

actual value of the room temperature with the room thermostat.

nConfiguration level 3: Operation of a base station in a WLAN network

Access to all system settings with direct connection to the WLAN

module.

nConfiguration level 4: Operation of several base stations via Internet

World-wide password-protected access to the system settings via

the router in the home network.

Chapter 2.8 „Configuration levels“ on page 29

Configuration levels

Product information

Fonterra Smart Control 9 from 115

nSimplified commissioning without manual hydraulic calibration.

nEnergy saving thanks to an intelligent heating concept.

nGeneration of individual heating profiles with

6 switching points per day for each room.

nPassword-protected configuration of individual utilisation units.

nUser-friendly representation and access to all functions via screen

menus.

nComfort functions:

– Limitation of the room temperatures that can be set at the room

thermostats

– Absence function with saving mode

– Protection from cool-down of the floor, also when the room is

heated by external heat sources such as insolation, open fire‐

places, etc.

– Priorisation of individual rooms in heat-up phases

– Long-term analysis of the supply temperatures – for the optimi‐

sation of the system settings

– Fault diagnosis system

2.5.2 Overview and description of component

Depending on the selected configuration level and the structural situa‐

tion, the parts must be ordered separately.

Chapter 2.8 „Configuration levels“ on page 29.

AKTOR

VL-TEMP

TAUP.

RS-232

RESET

Fig. 1: Component overview

1 - Radio amplifier / room thermostat

2 - Room thermostat / radio amplifier

3 - Basic unit

4 - WLAN module

5 - Actuator

6 - Actuator modules

7 - Flow sensor

A - Return flow beam

B - Supply flow beam

Features

Component overview

Product information

Fonterra Smart Control 10 from 115

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viega Controller Handbücher

Viega

Viega 1249 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung