Viessmann VITOTROL 200 RF Kurzanleitung

Installation and service

instructions

for contractors

VIESMANN

Vitotrol 200 RF

Wireless remote control for one heating circuit

For applicability, see the last page

VITOTROL 200 RF

5602 119 GB 3/2011 Please keep safe.

Please follow these safety instructions closely to prevent accidents and mate-

rial losses.

Safety instructions explained

Danger

This symbol warns against the

risk of injury.

!Please note

This symbol warns against the

risk of material losses and envi-

ronmental pollution.

Note

Details identified by the word "Note" con-

tain additional information.

Target group

These instructions are exclusively

designed for qualified personnel.

■ Work on gas equipment must only be

carried out by a qualified gas fitter.

■ Work on electrical equipment must

only be carried out by a qualified elec-

trician.

■ The system must be commissioned by

the system installer or a qualified per-

son authorised by the installer.

Regulations

Observe the following when working on

this system

■ all legal instructions regarding the pre-

vention of accidents,

■ all legal instructions regarding envi-

ronmental protection,

■ the Code of Practice of relevant trade

associations,

■ all current safety regulations as

defined by DIN, EN, DVGW, TRGI,

TRF, VDE and all locally applicable

standards,

■ Gas Safety (Installation & Use) Regu-

lations

– the appropriate Building Regulation

either the Building regulations, the

Building Regulation (Scotland),

Building Regulations (Northern Ire-

land),

– the Water Fittings Regulation or

Water Bylaws in Scotland,

– the current I.E.E. Wiring Regula-

tions.

If you smell gas

Danger

Escaping gas can lead to explo-

sions which may result in serious

injury.

■ Never smoke. Prevent naked

flames and sparks. Never

switch lights or electrical appli-

ances ON or OFF.

■ Close the gas shut-off valve.

■ Open windows and doors.

■ Remove all people from the

danger zone.

■ Notify your gas or electricity

supplier from outside the build-

ing.

■ Shut off the electricity supply to

the building from a safe place

(outside the building).

Safety instructions

5602 119 GB

If you smell flue gas

Danger

Flue gas can lead to life-threat-

ening poisoning.

■ Shut down the heating system.

■ Ventilate the boiler room.

■ Close all doors leading to the

living space.

Working on the system

■ When using gas as fuel, also close the

main gas shut-off valve and safeguard

against unauthorised reopening.

■ Isolate the system from the power sup-

ply and check that it is no longer 'live',

e.g. by removing a separate fuse or by

means of a main isolator.

■ Safeguard the system against unau-

thorised reconnection.

!Please note

Electronic modules can be dam-

aged by electro-static dis-

charges.

Touch earthed objects, such as

heating or water pipes, to dis-

charge static loads.

Repair work

!Please note

Repairing components which ful-

fil a safety function can compro-

mise the safe operation of your

heating system.

Replace faulty components only

with original Viessmann spare

parts.

Ancillary components, spare and

wearing parts

!Please note

Spare and wearing parts which

have not been tested together

with the heating system can com-

promise its function. Installing

non-authorised components and

non-approved modifications/con-

version can compromise safety

and may invalidate our warranty.

For replacements, use only orig-

inal spare parts from Viessmann

or those which are approved by

Viessmann.

Safety instructions

Safety instructions (cont.)

5602 119 GB

Installation instructions

Installation sequence

Usage information................................................................................................ 5

Installation location............................................................................................... 5

Commissioning the Vitotrol 200 RF...................................................................... 6

Checking the transmission and reception quality at the installation site.............. 8

Fitting the wall mounting base.............................................................................. 9

Inserting and removing the remote control........................................................... 9

Changing the heating circuit assignment following commissioning..................... 10

Changing the display contrast.............................................................................. 11

Service instructions

Troubleshooting

Fault display......................................................................................................... 12

Specification....................................................................................................... 13

Parts list.............................................................................................................. 14

Index

5602 119 GB

The Vitotrol 200 RF can be connected to

a Vitotronic control unit only in conjunc-

tion with the associated wireless base

station.

Up to three Vitotrol 200 RF can be log-

ged on at the same time at the wireless

base station of a Vitotronic control unit.

Installation location

Operation with or without room temperature hook-up

■Weather-compensated mode

Installation in any room.

■Operation with room temperature

hook-up

– On an internal wall in the main living

room, at a height of approx. 1.5 m

from the floor

– Not near windows or doors

– Not above radiators

– Not near heat sources (direct sun-

light, fireplace, TV set etc.)

Do not install further control devices in

this room. Any thermostatic radiator

valves must always be fully opened.

Wireless connection

Select the installation site of the Vitotrol

200 RF and the wireless base station so

that the radio signals are beamed as ver-

tically as possible onto walls and furnish-

ings.

Installation and service instruc-

tions, wireless base station

Note

Conducting metallic materials have a

strong negative effect on reception.

Prior to the final fitting at the preferred

installation site, commission the Vitotrol

200 RF and check the transmission and

reception quality at the installation site.

Installation sequence

Usage information

5602 119 GB

Installation

Prior to commissioning, observe the

following:

■ The wireless base station must be

connected with the control unit via a

KM BUS.

■ The control unit to which the wireless

base station is connected must be

switched on.

+ - + -

1. Site all the Vitotrol 200 RF near the

wireless base station.

2. Insert batteries (LR 6/AA, included in

the standard delivery) into the remote

control unit.

The configuration assistant then

starts automatically.

The display shows "CI" and "Lrn"

flashes.

Installation sequence

Commissioning the Vitotrol 200 RF

5602 119 GB

3. Press A on the wireless base sta-

tion:

■ Operation without wireless repeat-

ers: for 4 s. The green LED on the

wireless base station flashes

slowly.

■ Operation with wireless repeaters:

for 8 s. The green LED on the wire-

less base station flashes quickly.

Installation and service

instructions, wireless base

station

4. On the remote control, press OK.

The remote control unit transmits a

signal to log on at the wireless base

station.

■ Log on successful:

The display shows "C2" and

"000" (first digit flashes).

■ Log on unsuccessful:

The display shows "_ _ _ _ " and

Repeat the log on process.

5. Following successful log on, enter the

3-digit PIN at the remote control. The

PIN is printed on the protective foil on

the front of the wireless base station.

■ With +/- enter the first digit, then

confirm with OK.

■ With select the next position and

enter the next figure with +/-.

■ Confirm each entry with OK.

6. After the complete PIN has been

entered, "C3" and "H 1" will be

shown.

Then assign the required heating cir-

cuit (see the following chapter).

Installation sequence

Commissioning the Vitotrol 200 RF (cont.)

5602 119 GB

Installation

Assigning a heating circuit

1. Select the required heating circuit

with +/-:

■ Heating circuit 1 – "H 1"

■ Heating circuit 2 – "H 2"

■ Heating circuit 3 – "H 3"

2. OK to confirm.

The operating state of the heating

system is transferred.

The display segments rotate (for up

to 5 min).

Checking the transmission and reception quality at the instal-

lation site

1. Position the Vitotrol 200 RF at its

intended installation site.

2. Press OK and simultaneously for

approx. 4 s.

The display shows "dI" and "H .." for

the assigned heating circuit.

3. Call up a display of the transmission

and reception quality with / :

■ "d2": Vitotrol 200 RF

■ "d3": Wireless base station

■ "d4": Outside temperature sen-

sor RF

See the following table.

4. If the transmission and reception

quality is inadequate, either select a

different installation site and repeat

the check or use a wireless

repeater.

Display Value Transmission and reception quality

0 to - 78 extremely good

- 79 to - 83 good

- 84 to - 87 adequate

- 88 to - 91 inadequate

- 92 to - ... no reception

Installation sequence

Commissioning the Vitotrol 200 RF (cont.)

5602 119 GB

Inserting and removing the remote control

Insertion

Installation sequence

Fitting the wall mounting base

5602 119 GB

Installation

Removal

Changing the heating circuit assignment following commis-

sioning

1. Press and simultaneously at the

remote control for approx. 4 s.

2. With / select "C3".

3. With +/- select heating circuit 1

("H 1"), heating circuit 2 ("H 2") or

heating circuit 3 ("H 3").

4. OK to confirm.

The operating state of the heating

system is transferred.

The display segments rotate (for up

to 5 min).

Adjustments at the Vitotronic control

unit:

Set coding address "A0" for this heating

circuit at the control unit to 0 (fault mes-

sage bC, bd, bE).

Installation sequence

Inserting and removing the remote control (cont.)

5602 119 GB

Andere Handbücher für VITOTROL 200 RF

Inhaltsverzeichnis

Andere Viessmann Fernbedienung Handbücher

Viessmann

Viessmann Vitotrol 300-B Betriebsanleitung

Viessmann

Viessmann VITOTROL 200A Service-Handbuch

Viessmann

Viessmann Vitocom 100 Betriebsanleitung

Viessmann

Viessmann VITOTROL 200-E Bedienungsanleitung

Viessmann

Viessmann Vitotrol 200 Bedienungsanleitung

Viessmann

Viessmann Vitotrol 300-E Bedienungsanleitung

Viessmann

Viessmann Vitocom 100 Bedienungsanleitung

Viessmann

Viessmann VITOTROL 300 RF Betriebsanleitung

Viessmann

Viessmann Vitotrol 300 Bedienungsanleitung

Viessmann

Viessmann F remote control Bedienungsanleitung

Viessmann

Viessmann VITOTROL 200-E Kurzanleitung

Viessmann

Viessmann VITOTROL 100-E Bedienungsanleitung

Viessmann

Viessmann VITOTROL 200-E Bedienungsanleitung

Viessmann

Viessmann Vitotrol 300-B Betriebsanleitung

Viessmann

Viessmann Vitotrol 350 Kurzanleitung

Viessmann

Viessmann VITOTRONIC 200 Gebrauchsanweisung

Viessmann

Viessmann Vitocom 100 Kurzanleitung

Viessmann

Viessmann 7727449 Bedienungsanleitung

Viessmann

Viessmann Vitocom 100 Kurzanleitung

Viessmann

Viessmann VITOTROL 300A Kurzanleitung

Viessmann

Viessmann Vitocom 100 Kurzanleitung

Viessmann

Viessmann VITOTROL 300A Kurzanleitung

Viessmann

Viessmann VITOTRONIC 200 Bedienungsanleitung

Viessmann

Viessmann Vitotrol 300 Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung