ViewSonic TD2210 Bedienungsanleitung

TD2210

LCD Display

User Guide

Model No. VS14833

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Thank you for choosing ViewSonic

With over 30 years as a world leading provider of visual solutions,

ViewSonic is dedicated to exceeding the world’s expectations for

technological evolution, innovation, and simplicity. At ViewSonic, we

believe that our products have the potential to make a positive impact

in the world, and we are confident that the ViewSonic product you have

chosen will serve you well.

Once again, thank you for choosing ViewSonic !

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding

regulations. Confirmed corresponding applications shall refer to nameplate labels

and relevant markings on unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved

by the party responsible for compliance could void your authority to operate the

equipment.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage

Directive 2014/35/EU.

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and

Electronic Equipment Directive 2012/19/EU (WEEE).The mark indicates

the requirement NOT to dispose the equipment as unsorted municipal

waste, but use the return and collection systems according to local law.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use

of certain hazardous substances in electrical and electronic equipment (RoHS2

Directive) and is deemed to comply with the maximum concentration values issued

by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III

of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode uorescent lamps and external electrode uorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length (≦500 mm): maximum 3.5 mg per lamp.

(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.

(3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

iii

Important Safety Instructions

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this equipment near water. Warning: To reduce the risk of fire or

electric shock, do not expose this apparatus to rain or moisture.

6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the

Display” in this guide for further instructions.

7. Do not block any ventilation openings. Install the equipment in accordance with

the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including amplifiers) that produce heat.

9. Do not attempt to circumvent the safety provisions of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade

and the third prong are provided for your safety. If the plug does not fit into your

outlet, consult an electrician for replacement of the outlet.

10. Protect the power cord from being tread upon or pinched, particularly at the plug,

and the point where if emerges from the equipment. Be sure that the power outlet

is located near the equipment so that it is easily accessible.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the equipment. When a cart is used,

use caution when moving the cart/equipment combination to avoid

injury from tipping over.

13. Unplug this equipment when it will be unused for long periods of time.

14. Refer all servicing to qualified service personnel. Service is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

15. Moisture may appear on the screen due to environmental changes. However, it

will disappear after a few minutes.

Contents

Compliance Information

FCC Compliance Statement...................................................................................i

Industry Canada Statement....................................................................................i

CE Conformity for European Countries..................................................................i

Declaration of RoHS2 Compliance........................................................................ii

Important Safety Instructions................................................................................ iii

Product Registration..............................................................................................2

For Your Records ..................................................................................................2

Getting Started

Package Contents .................................................................................................3

Quick Installation ...................................................................................................4

Additional Software Installation (Optional).............................................................4

Control of the Touch Function ...............................................................................5

Wall Mounting (Optional).......................................................................................6

Using the LCD Display

Setting the Timing Mode........................................................................................7

OSD and Power Lock Settings..............................................................................7

Adjusting the Screen Image ..................................................................................8

Main Menu Controls ..............................................................................................9

Main Menu Explanation.........................................................................................9

Power Management ............................................................................................10

Other Information

Specifications ......................................................................................................11

Cleaning the LCD Display ...................................................................................12

Touch Screen Cleaning Procedure .....................................................................13

Troubleshooting...................................................................................................14

Customer Support ...............................................................................................15

Limited Warranty .................................................................................................16

Mexico Limited Warranty.....................................................................................18

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS, DisplayPort, and DDC are trademarks of VESA.

ENERGY STAR®is a registered trademark of the U.S. Environmental Protection

Agency (EPA).

As an ENERGY STAR®partner, ViewSonic Corporation has determined that this

product meets the ENERGY STAR®guidelines for energy efficiency.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting

from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves

the right to change product specifications without notice. Information in this

document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information

as it becomes available, please visit your region section on ViewSonic’s website to

The ViewSonic CD also provides an opportunity for you to print the product

registration form. Upon completion, please mail or fax to a respective ViewSonic

office. To find your registration form, use the directory “:\CD\Registration”.

Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section.

Your LCD displays serial number is located on the rear side of the display.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

TD2210

ViewSonic Widescreen LCD Display

VS14833

TD2210_UG_ENG Rev. 1B 10-16-19

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of Smarter, Greener Computing.

Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/eu/support/call-desk/

Taiwan: http://recycle.epa.gov.tw/

Getting Started

Congratulations on your purchase of a ViewSonic®LCD display.

Important! Save the original box and all packing material for future shipping needs.

NOTE: The word “Windows” in this user guide refers to Microsoft Windows operating

system.

Package Contents

Your LCD display package includes:

• LCD display

• Power cord

• D-Sub cable

• DVI cable

• USB cable

• Quick Start Guide

NOTE: The INF file ensures compatibility with Windows operating systems, and

the ICM file (Image Color Matching) ensures accurate on-screen colors. ViewSonic

recommends that you install both the INF and ICM files.

Quick Installation

1. Connect video cable

• Make sure both the LCD display and computer are turned OFF.

• Remove rear panel covers if necessary.

• Connect the video cable from the LCD display to the computer.

2. Connect power cord (and AC/DC adapter if required)

Macintosh users: Models older than G3 require a Macintosh adapter. Attach the

adapter to the computer and plug the video cable into the adapter.

USB UP

USB DOWN

Power Cord

D-Sub

DVI

3. Turn ON LCD display and computer

Turn ON the LCD display, then turn ON the computer. This sequence (LCD

display before computer) is important.

4. Windows users: Set the timing mode (example: 1024 x 768)

For instructions on changing the resolution and refresh rate, see the graphics

card’s user guide.

5. Installation is complete. Enjoy your new ViewSonic LCD display.

Additional Software Installation (Optional)

1. Load the ViewSonic CD on your CD/DVD drive.

2. Double click on the "Software" folder and choose an application, if desired.

3. Double click on the Setup.exe file and follow the onscreen instructions to

complete the simple installation.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ViewSonic Monitor Handbücher

ViewSonic

ViewSonic VA2013wm-4 Bedienungsanleitung

ViewSonic

ViewSonic VX2267-mhd Bedienungsanleitung

ViewSonic

ViewSonic VX715 - 17" LCD Monitor Bedienungsanleitung

ViewSonic

ViewSonic ViewPanel VG191 Bedienungsanleitung

ViewSonic

ViewSonic VG2433-LED Bedienungsanleitung

ViewSonic

ViewSonic VS15882 Bedienungsanleitung

ViewSonic

ViewSonic 21PS Bedienungsanleitung

ViewSonic

ViewSonic P70f Bedienungsanleitung

ViewSonic

ViewSonic VA2410 Bedienungsanleitung

ViewSonic

ViewSonic ColorPro VP2456 Bedienungsanleitung

ViewSonic

ViewSonic VA1938wa-LED Bedienungsanleitung

ViewSonic

ViewSonic VA2213w Bedienungsanleitung

ViewSonic

ViewSonic Q9-1 Bedienungsanleitung

ViewSonic

ViewSonic VCDTS23283 Bedienungsanleitung

ViewSonic

ViewSonic LCD Display VS11349 Bedienungsanleitung

ViewSonic

ViewSonic LDS135-151 Bedienungsanleitung

ViewSonic

ViewSonic VG2030WM - 20" LCD Monitor Bedienungsanleitung

ViewSonic

ViewSonic VA703B - 17" LCD Monitor Bedienungsanleitung

ViewSonic

ViewSonic CDE5560T Bedienungsanleitung

ViewSonic

ViewSonic VS12400 Bedienungsanleitung

ViewSonic

ViewSonic LCD Display VS11349 Bedienungsanleitung

ViewSonic

ViewSonic VS11886 Bedienungsanleitung

ViewSonic

ViewSonic VA1932wa Bedienungsanleitung

ViewSonic

ViewSonic VG150 - 15" LCD Monitor Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung