ViewSonic PJ862 Bedienungsanleitung

Quick Start Reference Sheet

ViewSonic PJ862

Revision A

04/12/05 SP Controls reserves the right to modify specifications without notice at any time.

NOTE: This one-page document is intended only as a quick reference for installation – please read

the SP Controls Application Note for a complete description of this projector driver prior to installation.

I. Driver Features

1. Input Selection Mapping

Selection 1: VIDEO

Selection 2: S-VIDEO

Selection 3: RGB 1

Selection 4: RGB 2

2. Hidden Function Mapping (Default Configuration)

Using the ON button as a shift key, press the following buttons to access the specified projector features.

Selection 1: AUTO IMAGE

Selection 2: MUTE

Selection 3: ADJ LEFT

Selection 4: ADJ RIGHT

Off: MENU

Volume Up: ADJ UP

Volume Down: ADJ DOWN

3. Other Driver Features

Power Status Feedback Method RS-232 Power Polling

Control Wiring: RS-232 and IR-Emitter

II. Wiring Specifications

NOTE: For a wiring diagram, please see the SP Controls Application Note following this document.

1. RS-232:

Wire the Panel RS-232 port to a female DB9 as follows:

TX to 2

RX to 3

GND to 5

Connect this female DP9 to the projector port labeled CONTROL.

2. Infrared Emitter:

Wire the Panel IR/Serial port to a female 1/8" Mini as follows:

IR/SER to tip

GND to ring

Connect to the included IR Emitter and attach the emitter bud to any projector IR window.

Projector Driver Application Note

ViewSonic PJ862

Revision A

04/12/05 SP Controls reserves the right to modify specifications without notice at any time.

This document describes the SmartPanel Projector Driver for the ViewSonic PJ862 projector. For more

information on configuring and using the Panel see the SmartPanel Configuration and Installation Guide.

I. PROJECTOR CONTROL

A. Volume and Power Control

Volume control for the ViewSonic is relative.

Absolute volume control for this model is possible with use of SP Controls’ optional Audio Follow Video

Pre-Amplifier (SP3-AFVP+).

B. Input Selection Mapping

The following table specifies the factory-preset input mapping for this Driver. The Configuration Utility

can be used to customize these settings your installation.

Selection 1: VIDEO

Selection 2: S-VIDEO

Selection 3: RGB 1

Selection 4: RGB 2

Input choices available with this Driver are

VIDEO, S-VIDEO, COMPOSITE VIDEO, RGB 1,

RGB 2, and DIGITIAL (DVI).

C. Hidden Function Mapping

The following table specifies the factory preset hidden function mapping for this Driver. The

Configuration Utility can be used to customize these settings your installation.

Selection 1: AUTO IMAGE

Selection 2: MUTE

Selection 3: ADJ LEFT

Selection 4: ADJ RIGHT

Off: MENU

Volume Up: ADJ UP

Volume Down: ADJ DOWN

Hidden functions names are based on the ViewSonic remote control and projector-top controls.

Menu both summons and dismisses on screen menus. ADJUST controls navigate through onscreen

menus. BLANK, MUTE, and FREEZE are toggles. AUTO IMAGE only works when one of the RGB

inputs is selected.

Hidden functions are accessed by pressing the indicated key while the holding the On key down.

Projector

Ready

Warm-up

OFF

Volume

VIDEO

S-VIDEO

RGB 1 RGB 2

Projector

Ready

Warm-up

OFF

Volume

ADJ UP

DJ DOW

AUTO IMG

MUTE

ADJ LEFT ADJ RIGHT

SmartPanel Projector Driver Application Note ViewSonic PJ862

The hidden functions available for the ViewSonic with this Driver are as follows:

ADJ UP

ADJ DOWN

ADJ LEFT

ADJ RIGHT

MAGNIFY +

MAGNIFY -

MAGNIFY OFF

BLANK

MUTE

FREEZE

AUTO IMAGE

D. Relays

The following table specifies the factory-preset

settings for the low-current relays found on the rear

of the SmartPanel. The Configuration Utility can

be used to customize these settings your installation.

Relay 1 ON Maintained

Relay 2 ON Momentary

Relay 3 OFF Momentary

Selection Momentary; not Binary

E. Other Presets

The following table specifies other default factory settings for this Driver that affect is control of the

Projector.

Power Status Feedback Method RS-232 Polling (see note 1)

Control Wiring Option Infrared Emitter (see note 2)

Control for the ViewSonic with this Driver is via both RS-232 and Infrared.

The following table specifies settings for the Panel’s configurable timers. For more information on the

inactivity shutdown feature and the lockout timer see the SmartPanel Configuration and Installation

Guide.

Lockout Timer 81 seconds (see note 3)

Inactivity Shutdown Disabled

RELAYS

PWR

MAINT.

PWR

MOM.

PWR

OFF

MOM.

SELECTION

(EXT. SWITCHER CTRL)

4321

500mA MAX. CURRENT

SmartPanel Projector Driver Application Note ViewSonic PJ862

II. CONTROL WIRING

PROJECTOR CONTROL

RS232 IR/SERIAL

GND

CTS

RTS

+12V

GND

IR/SER

SENSE

RS-232 to

CONTROL

IR Emitter

(included with Panel)

1/8" Mini

Female

IR Emitter to

any IR window

Female DB9

54321

9876

5432 1

This section specifies how RS-232 and Infrared should be

wired to the ViewSonic projector.

A. RS-232 should be connected to the female DB9

terminal labeled CONTROL. Connection should be as

follows:

1. Wire the Panel to a female DB9 as follows:

TX to 2

RX to 3

GND to 5

2. Connect this female connector to the projector port

labeled CONTROL.

B. The IR Emitter should be connected to the one of the

ViewSonic IR windows as follows:

1. Wire the Panel to a female 1/8” Mini as show; wire

IR/SER to tip and GND to ring. Splicing and direct

wiring to the IR Emitter is not recommended as it

makes removal of the Panel for service more difficult.

2. Connect the included IR Emitter to the female mini.

3. Affix the IR Emitter to one of the IR windows on the

projector.

Note that the emitter glows red when IR is emitted so wiring

can be verified.

SmartPanel Projector Driver Application Note ViewSonic PJ862

III. TROUBLESHOOTING

Additional tips can be found in the SmartPanel Configuration and Installation Guide.

The Panel does not do anything at all.

When power is applied to the Panel it should run through a brief power on self-test, during which all of

the Panel lights will turn on and off in sequence. If you do not see this self-test, make sure power is

connected correctly and that polarity is correct.

The Panel keeps turning itself off even though the projector is on.

The Panel turns itself off when power verification indicates that the projector is off. Check to make

sure the RS-232 connection is correctly wired. If a third party power current sensor is being used,

make sure correctly wired and calibrated. The most common cause for power polling failure when

other control works, is that the RX line is incorrectly wired or soldered.

The projector keeps turning itself off, though the Panel is on (then the Panel then shuts itself off).

The ViewSonic may be configured through the OPTIONS (OPT.) menu to shut itself off in the

absence of a valid input signal. Refer to the ViewSonic manual for more information. Also, ensure

that Panel is not configured with an unexpected value for Inactivity Shutdown.

When I try to turn the projector on, the warming indicator (red LED) blink.

The projector is in lockout mode, and the Panel is waiting for its internal lockout timer to expire; this

feature protects the projector’s bulb. Be sure to let your client know about this behavior.

IV. TECHNICAL NOTES

1. By default, projector power is verified by polling every few seconds via the RS-232 port. Power

polling can be suspended by depressing and holding the On key; polling will be restored when the

key is released. Should the ViewSonic power off, the Panel will usually detect this condition and

power off within thirty seconds. Should the ViewSonic power on, the Panel will usually detecting this

condition and power on within fifteen seconds.

2. This ViewSonic is currently controlled via a combination of Infrared and RS-232 only. Wired Remote

is not an option as the ViewSonic does not have a Wired Remote port.

3. The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER

ON to the projector (the delay allows the projector bulb to cool before re-powering). This delay can

be configured using the Configuration Utility; however, adjusting the lockout timer delay is

strongly discouraged as rapid re-powering causes undue wear on the projector’s bulb. Also, the

ViewSonic will not allow power to be restored before a minimum delay has expired. Therefore,

disabling the lockout delay will cause potentially confusing Panel behavior.

V. REVISION HISTORY

1. Revision A (April, 2005) Initial Revision

Andere Handbücher für PJ862

Inhaltsverzeichnis

Andere ViewSonic Projektor Handbücher

ViewSonic

ViewSonic PA504W Series Bedienungsanleitung

ViewSonic

ViewSonic PJ552 Bedienungsanleitung

ViewSonic

ViewSonic PJD5133-S Bedienungsanleitung

ViewSonic

ViewSonic Office Theater PJ1060 Bedienungsanleitung

ViewSonic

ViewSonic PJD6544w Bedienungsanleitung

ViewSonic

ViewSonic PJ750 Bedienungsanleitung

ViewSonic

ViewSonic VS18021 Bedienungsanleitung

ViewSonic

ViewSonic M10 Bedienungsanleitung

ViewSonic

ViewSonic VS11580 Kurzanleitung

ViewSonic

ViewSonic PJD5126 Bedienungsanleitung

ViewSonic

ViewSonic Office Theater PJ820 Bedienungsanleitung

ViewSonic

ViewSonic PJ658 - XGA LCD Projector Bedienungsanleitung

ViewSonic

ViewSonic PJD7828HDL Bedienungsanleitung

ViewSonic

ViewSonic PJL7201 Bedienungsanleitung

ViewSonic

ViewSonic LiteBird PJ870 Bedienungsanleitung

ViewSonic

ViewSonic PJ588D - DLP Hi-Brightness Portable... Bedienungsanleitung

ViewSonic

ViewSonic PJD6243 Bedienungsanleitung

ViewSonic

ViewSonic LS810 Bedienungsanleitung

ViewSonic

ViewSonic VS17689 Bedienungsanleitung

ViewSonic

ViewSonic PX749-4K Bedienungsanleitung

ViewSonic

ViewSonic VS11452 Schulungshandbuch

ViewSonic

ViewSonic Pro10100 Bedienungsanleitung

ViewSonic

ViewSonic PJD5122 Bedienungsanleitung

ViewSonic

ViewSonic PJL7200 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung