ViewSonic PJD5132 Bedienungsanleitung

PJD5132/PJD5232L/PJD5134/

PJD5234L/PJD5533w

DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://www.

YLHZVRQLFFRPLQ(QJOLVKRULQVSHFL¿FODQJXDJHVXVLQJWKH5HJLRQDOVHOHFWLRQER[LQWKH

upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las

instrucciones en este manual”

Model No. VS14926/VS14929/VS14928/VS14930/VS14117

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy, and if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

y&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS

Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKH

party responsible for compliance could void your authority to operate the equipment.

For Canada

yThis Class B digital apparatus complies with Canadian ICES-003.

yCet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage

Directive 2006/95/EC.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive

2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment including any spent

or discarded batteries or accumulators as unsorted municipal waste, but use the return

and collection systems available.

If the batteries, accumulators and button cells included with this equipment, display

the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal

content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than

0.004% Lead.

Compliance Information

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

GHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade and the third prong are provided for your safety. If

WKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXURXWOHWFRQVXOWDQHOHFWULFLDQIRUUHSODFHPHQWRIWKH

obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience

UHFHSWDFOHVDQGWKHSRLQWZKHUHWKH\H[LWIURPWKHXQLW%HVXUHWKDWWKHSRZHURXWOHWLV

located near the unit so that it is easily accessible.

 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU

8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\WKH

manufacturer, or sold with the unit. When a cart is used, use caution when moving

the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKHXQLWKDV

been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid

LVVSLOOHGRQWRRUREMHFWVIDOOLQWRWKHXQLWLIWKHXQLWLVH[SRVHGWRUDLQRUPRLVWXUHRULIWKH

unit does not operate normally or has been dropped.

iii

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/EC

of the European Parliament and the Council on restriction of the use of certain hazardous

substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply

ZLWKWKHPD[LPXPFRQFHQWUDWLRQYDOXHVLVVXHGE\WKH(XURSHDQ7HFKQLFDO$GDSWDWLRQ

Committee (TAC) as shown below:

Substance Proposed Maximum

Concentration Actual Concentration

Lead (Pb) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

+H[DYDOHQW&KURPLXP&U6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

&HUWDLQFRPSRQHQWVRISURGXFWVDVVWDWHGDERYHDUHH[HPSWHGXQGHUWKH$QQH[RIWKH5R+6

Directives as noted below:

([DPSOHVRIH[HPSWHGFRPSRQHQWVDUH

1. /HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQGHOHF-

tronic ceramic parts (e.g. piezoelectronic devices).

2. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or

more lead).

3. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium

containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by

weight.

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks

of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and

DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omis-

sions contained herein; nor for incidental or consequential damages resulting from furnishing

this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to

FKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFXPHQWPD\FKDQJHZLWKRXW

notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any

purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes

available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic®

Wizard CD-ROM also provides an opportunity for you to print the registration form, which you

PD\PDLORUID[WR9LHZ6RQLF

For Your Records

Product Name: PJD5132/PJD5232L/PJD5134/PJD5234L/PJD5533w

ViewSonic DLP Projector

Model Number: VS14926/VS14929/VS14928/VS14930/VS14117

Document Number: PJD5132/PJD5232L/PJD5134/PJD5234L/PJD5533w_

UG_ENG Rev. 1A 11-21-12

Serial Number: ___________________________________________

Purchase Date: ___________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the environment.

Please use care and dispose of in accordance with local, state or federal laws.

ViewSonic respects the environment and is committed to working and living green. Thank you

for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

7DLZDQKWWSUHF\FOHHSDJRYWZUHF\FOHLQGH[DVS[

Table of contents

Important safety

instructions .......................2

Introduction......................4

Projector features ................................. 4

Shipping contents................................. 5

Projector exterior view......................... 6

Controls and functions ......................... 7

Positioning your

projector..........................12

Choosing a location............................ 12

Projection dimensions........................ 13

Connection ......................15

Connecting a computer or monitor .... 16

Connecting Video source devices...... 17

Operation ........................20

Starting up the projector..................... 20

Using the menus................................. 21

Utilizing the password function ......... 22

Switching input signal........................ 25

Adjusting the projected image ........... 26

Magnifying and searching for details. 27

Selecting the aspect ratio ................... 28

Optimizing the image......................... 31

Setting the presentation timer ............ 35

Hiding the image................................ 36

Locking control keys.......................... 36

Freezing the image............................. 36

Operating in a high altitude

environment ....................................... 36

Using the CEC function ..................... 37

Using the 3D functions ...................... 37

Using the projector in standby mode. 38

Shutting down the projector .............. 39

Menu operation.................................. 40

Maintenance ...................50

Care of the projector .......................... 50

Lamp information .............................. 51

Troubleshooting .............57

Specifications ..................58

Projector specifications...................... 58

Dimensions ........................................ 60

Ceiling mount installation ................. 60

Timing chart ...................................... 61

Appendix.........................64

IR control table .................................. 64

RS232 command table....................... 66

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information

technology equipment. However, to ensure safe use of this product, it is important that you

follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before you operate your projector. Save it for future

reference.

2. Do not look straight at the projector lens during operation. The intense light beam

may damage your eyes.

3. Refer servicing to qualified service personnel.

4. Always open the lens shutter or remove the lens cap when the projector lamp is

on.

5. In some countries, the line voltage is NOT stable. This projector is designed to operate

safely within a mains voltage between 100 to 240 volts AC, but could fail if power

cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate

or cut out, it is recommended that you connect your projector through a power

stabilizer, surge protector or uninterruptible power supply (UPS).

6. Do not block the projection lens with any objects when the projector is under

operation as this could cause the objects to become heated and deformed or even

cause a fire. To temporarily turn off the lamp, press BLANK on the projector or

remote control.

7. The lamp becomes extremely hot during operation. Allow the projector to cool for

approximately 45 minutes prior to removing the lamp assembly for replacement.

8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps

beyond the rated life could cause them to break on rare occasions.

9. Never replace the lamp assembly or any electronic components unless the projector is

unplugged.

10. Do not place this product on an unstable cart, stand, or table. The product may fall,

sustaining serious damage.

11. Do not attempt to disassemble this projector. There are dangerous high voltages inside

which may cause death if you should come into contact with live parts. The only user

serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer

servicing only to suitably qualified professional service personnel.

12. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls

and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a

car with all windows rolled up.

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical

components, shortening the projector's life span and darkening the picture.

- Locations near fire alarms

- Locations with an ambient temperature above 40°C / 104°F

- Locations where the altitudes are higher than 3000 m (10000 feet).

13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,

overheating inside the projector may result in a fire.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

14. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of

more than 15 degrees front to back. Using the projector when it is not fully horizontal

may cause a malfunction of, or damage to, the lamp.

15. Do not stand the projector on end vertically. Doing so may cause the projector to fall

over, causing injury or resulting in damage to the projector.

16. Do not step on the projector or place any objects upon it. Besides probable physical

damage to the projector, doing so may result in accidents and possible injury.

17. Do not place liquids near or on the projector. Liquids spilled into the projector may

cause it to fail. If the projector does become wet, disconnect it from the power

supply's wall socket and call your local service center to have the projector serviced.

18. This product is capable of displaying inverted pictures for ceiling mount installation.

Use only qualified ceiling mount kit for mounting the projector and ensure it is

securely installed.

19. When the projector is under operation, you may sense some heated air and odor from

its ventilation grill. It is a normal phenomenon and not a product defect.

20. Do not use the Security bar for transporting or installation. It should be used with a

commercially available theft prevention cable.

Safety instructions for ceiling mounting of the

projector

We want you to have a pleasant experience using your projector, so we need to bring this

safety matter to your attention to prevent damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a

proper fitting projector ceiling mount kit and that you ensure it is securely and safely

installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the

projector may fall from the ceiling due to an improper attachment through the use of the

wrong gauge or length screws.

You can purchase a projector ceiling mount kit from the place you purchased your projector.

We recommends that you also purchase a separate Kensington lock compatible security

cable and attach it securely to both the Kensington lock slot on the projector and the base of

the ceiling mount bracket. This will perform the secondary role of restraining the projector

should its attachment to the mounting bracket become loose.

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly

design to deliver high reliability and ease of use.

The projector offers the following features.

• Dynamic PC and Dynamic Movie functions adjusting the power consumption of the

lamp according to the brightness of the image being projected

• DynamicEco Timer function decreasing the power consumption of the lamp by up to

30% when no input signal can be detected for a set period of time.

• Presentation timer for better control of time during presentations

• Supports 3D display

• Color Management allowing color adjustments to your liking

• Less than 0.5W power consumption when power saving mode is turned on

• Screen Color correction allowing projection on surfaces of several predefined colors

• Quick auto search speeding up the signal detecting process

• Color and Reference modes providing choices for different projection purposes

• Selectable quick power off function

• One-key auto-adjustment to display the best picture quality

• Digital keystone correction to correct distorted images

• Adjustable color management control for data/video display

• Ability to display 1.07 billion colors

• Multi-language On-Screen Display (OSD) menus

• Switchable normal and economic modes to reduce the power consumption

• Component HDTV compatibility (YPbPr)

• HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/

OFF operation between the projector and a CEC-compatible device connected to the

HDMI input of the projector (PJD5134/PJD5234L/PJD5533w models only)

• The apparent brightness of the projected image will vary depending on the ambient

lighting conditions, selected input signal contrast/brightness settings, and is directly

proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturers

specifications. This is normal and expected behavior.

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these

items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those

illustrated.

Optional accessories

1. Replacement lamp

2. Soft carry case

3. VGA-Component adapter

Projector Power Cord VGA Cable

Multi-language user

manual DVD Quick Start Guide Remote Control & Batteries

Andere Handbücher für PJD5132

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ViewSonic Projektor Handbücher

ViewSonic

ViewSonic PJ358 - XGA LCD Projector Bedienungsanleitung

ViewSonic

ViewSonic PJ558D Bedienungsanleitung

ViewSonic

ViewSonic LS850WU Bedienungsanleitung

ViewSonic

ViewSonic PJD5211 Bedienungsanleitung

ViewSonic

ViewSonic Pro6200 Bedienungsanleitung

ViewSonic

ViewSonic PJD6350 Bedienungsanleitung

ViewSonic

ViewSonic PJ1158-1 Bedienungsanleitung

ViewSonic

ViewSonic M2 Bedienungsanleitung

ViewSonic

ViewSonic PJ1172 - XGA LCD Projector Bedienungsanleitung

ViewSonic

ViewSonic Pro8600 Bedienungsanleitung

ViewSonic

ViewSonic PJD6253 Bedienungsanleitung

ViewSonic

ViewSonic PJ458D - XGA DLP Projector Bedienungsanleitung

ViewSonic

ViewSonic CINE1000 - DLP Home Theater Projector Bedienungsanleitung

ViewSonic

ViewSonic M1 mini Bedienungsanleitung

ViewSonic

ViewSonic PJL9371 Leitfaden

ViewSonic

ViewSonic PJ656D Bedienungsanleitung

ViewSonic

ViewSonic M1 mini Bedienungsanleitung

ViewSonic

ViewSonic X10-4K Bedienungsanleitung

ViewSonic

ViewSonic PJD6345 Bedienungsanleitung

ViewSonic

ViewSonic PJD6253 Bedienungsanleitung

ViewSonic

ViewSonic PJD5155L Bedienungsanleitung

ViewSonic

ViewSonic PJ506D - SVGA DLP Projector Bedienungsanleitung

ViewSonic

ViewSonic VS11949 Bedienungsanleitung

ViewSonic

ViewSonic PRO9500 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung