Viking VP3000 Bedienungsanleitung

The Viking VP3000 Axial Air Mover features patent

pending FOCUSTM Technology. FOCUSTM Technology

revolutionizes evaporative drying by producing air

velocities greater than competitive product offerings.

This highly focused air flow is directed towards the

restoration industry’s problematic drying areas

namely, carpet and pad, sub-floor, sill plate and

walls. The Viking VP3000 Axial Air Mover with

FOCUSTM Technology sustains these air velocities

further than any other axial air mover.

The Viking VP3000 Axial Air Mover includes a

2-speed motor delivering a focused airstream of

approximately 3000 cfm and a lightweight stackable

enclosure designed to fit existing vehicle rigging,

on-board duplex GFIC outlet, circuit breaker, and

superior cord namagement.

FOCUSTM Technology Features & Benefits

Focused Air Flow •Approximately 3000 CFM air flow directed where you need it. Patent

pending FOCUSTM Technologydirects air towards the corner of walls

and floors to dry the sill plate quickly

Power Management •Operator interface conveniently located for easy access, featuring:

three-position switch, circuit breaker and GFCI outlet.

Packaged for Use •Comes “ready-to-use” in the box.

•Unique offset handle promotes ease-of-use.

•Units interlock for ease of stacking during storage and handling.

•More pleasing sound than competitive units.

Weight • Weighs 2.5 lbs less than competitive units.

Housing •Linear low density polyethylene construction.

•Unique housing and matched blade/motor result in quiet operation.

•Easily serviced.

Long-life Motor •Low bearing temperatures increase motor life.

•Permawick®Lubrication.

Viking VP3000 Axial Air Mover

Owner’s Manual TS-341

Owner’s Manual |Viking VP3000 Axial Air Mover

Read And Save These Instructions

2VIKING VP3000 AXIAL AIR MOVER with FOCUS™Technology Owners Manual

Table of Contents

Introduction 1

FOCUSTM Technology Features & Benefits 1

Safety Precautions 2

Intended Application for VP3000 AXIAL AIR MOVER 3

Registrations 3

Specifications 3

Integrated Cord Wrap 3

VP3000 AXIAL AIR MOVER Operation

Operating Instructions 4

VP3000 AXIAL AIR MOVER Operator Panel Features

3-Position Drying Selector Switch 4

12 amp Curcuit Breaker

GFCI Protection

Maintaining Your VP3000 AXIAL AIR MOVER

Servicing 4

Motor Lubrication 4

Cleaning 4

Replacement Parts and 4

Optional Accessories

VP3000 AXIAL AIR MOVER Applications

Sizing for Water Restoration Jobs 5

Placement 5

Orientation 5

Air Flow Diagrams 5

Performance Chart 5

Warranty 6

READ AND SAVE THESE INSTRUCTIONS

•Do not operate the unit with a cut or frayed power cord.

•Do not unplug the unit by pulling on the cord. Grasp the

plug firmly and pull it out of the wall socket or power

receptacle.

•Always use a grounded outlet.

•Never operate electrical equipment in standing water.

•Never operate with the safety grills removed. Personal injury

may result.

•

Do not stick your fingers or other objects through the safety

grills.

•Do not restrict airflow to the unit. This may cause the

unit to overheat.

•Unit should never be serviced or cleaned while it is

plugged in.

•Do not sit or stand on the unit or use as a shelf or table.

•Before leaving an AXIAL AIR MOVER unattended, ensure chil-

dren do not have access to the equipment. Do not allow

children to play with or near the unit or in its air flow.

•To reduce the risk of fire or electric shock, do not use

this air mover with any solid-state speed control device.

LIRE ET CONSERVER CES INSTRUCTIONS

•Risque de choc électrique Peut causer des blessures ou

la mort. Débrancher toutes les alimentations en courant

électrique à distance avant l'entretien ou le nettoyage.

•Ne pas utiliser l'appareil avec un cordon d'alimentation

coupé ou effiloché.

•Ne pas débrancher l'appareil en tirant sur le cordon.

Tenir la fiche fermement et la tirer horsde la prise

murale ou la prise d'alimentation électrique.

•Toujours utiliser une prise mise à la terre.

•Ne jamais utiliser l'équipement électrique dans de l'eau

stagnante.

•Ne jamais utiliser sans les grilles de protection. Des

blessures risquent d'en résulter.

•Ne pas passer les doigts ou d'autres objets dans les

grilles de protection.

•Ne pas diminuer le débit d'air arrivant jusqu'à l'appareil.

L'appareil risque de trop chauffer.

•Ne pas s'asseoir ou se tenir debout sur l'appareil; ne

pas l'utiliser comme étagère ou table.

•Avant de laisser un appareil aéraulique axial sans surveil-

lance, s'assurer que les enfants n'ont pas accès à

l'équipement. Ne pas laisser les enfants jouer avec

l'appareil ou à proximité de l'appareil ou dans l'air qu'il

projette.

•Pour réduire le risque d'incendie ou de choc électrique,

ne pas utiliser ce ventilateur avec un dispositif de com-

mande de vitesse à semi-conducteurs.

VIKING VP3000 AXIAL AIR MOVER with FOCUS™TechnologyOwnersManual 3

Figure 3:Cord wrap

Intended Application for VIKING VP3000

AXIAL AIR MOVER

The VIKING VP3000 AXIAL AIR MOVER minimizes overall dry-

ing time on water restoration jobs. The VIKING VP3000

AXIAL AIR MOVER uses patent pending FOCUS Technology

to maximize air velocity across floors and along walls for

longer distances. By maximizing the air velocity, water

evaporates more quickly from the carpet, pad, sub-floor,

wall, and sill plate. We optimized the VIKING VP3000 AXIAL

AIR MOVER todry structures through rapid evaporation.

Registrations

The Viking VP3000 Axial Air Mover conforms to UL STD

507.

Certified to CAN/CSA STD C22.2 No. 113.

Specifications

Size Height: 19.5”

Width: 19.9”

Depth: 15.2” (intake to exhaust)

Weight 29.5 lbs; Shipping Weight–32.7 lbs

Motor 1/4 hp 1-phase 110/120 VAC 2-speed

4-pole, PSC Electric Motor.

CFM Approximately 3000

Cord 20ft Power Cord

Current Draw 2.5 Amps

Voltage 115 VAC

Power Requirements and Daisy-Chaining

the VIKING VP3000 AXIAL AIR MOVER

The VIKING VP3000 AXIAL AIR MOVER draws 2.5 amps. The

12 amp, on-board circuit breaker will allow four (4) VIKING

VP3000 AXIAL AIR MOVERS on one circuit. When daisy-

chaining the VIKING VP3000 AXIAL AIR MOVER,turn on one

VIKING VP3000 AXIAL AIR MOVER at a time to prevent exces-

sive current inrush caused by four units starting at once.

Aground fault in the VIKING VP3000 AXIAL AIR MOVER or

anywhere on the circuit will cause the AXIAL AIR MOVER’S

GFCI to trip. After rectifying the ground fault, reset the

GFCI bypressing the reset button.

Recommended Use

Recommended use(s) of on-board duplex GFCI are show in

Figure 2. NOTE: Standard 115 VAC electrical outlets.

15Amp

Outlet

15 Amp

Outlet

15Amp

Outlet

Phoenix 200 MAX

Figure 2: Duplex

GFCI use. Phoenix Mini-Guardian

Integrated Cord Wrap

The VIKING VP3000 AXIAL AIR MOVER features integrated cord

management. Wrap the cord around the cord wrap as

shown and secure the cord with the clasp on the plug.

Figure 1: Too many AXIAL AIR MOVERS daisy-chained.

4VIKING VP3000 AXIAL AIR MOVER with FOCUS™Technology Owners Manual

Axial Air Mover Operation

Operating Instructions

The VIKING VP3000 AXIAL AIR MOVER aspackaged is ready to

be put into service. Inspect the unit completely for any

shipping damage. Place the unit on the ground. Orient the

unit so the desired air flow direction is the same as the

indicator in the FOCUS Technology corner on the interior of

the unit. Plug the unit into a grounded outlet and select the

drying mode.

VP3000 AXIAL AIR MOVER

Operator Panel Features

3-Position Drying Selector Switch

A3-position drying mode selector switch is used to select

the VIKING VP3000 AXIAL AIR MOVER’Smode of operation. The

three modes of operation are OFF, LOW or HIGH.

OFF -The VP3000 AXIAL AIR MOVER is not drying.

LOW -The VP3000 AXIAL AIR MOVER is in “Normal” Drying

mode. This mode provides rapid drying and very quiet

operation.

HIGH - The VP3000 AXIAL AIR MOVER is in “Ultra” drying

mode. This mode provides rapid drying and low noise,

quiet operation.

Maintaining Your Axial Air Mover

Servicing

Before each use, the VIKING VP3000 AXIAL AIR MOVER should

be inspected for damage, blocked inlet or outlet, or any

excess buildup of foreign material.

When the VIKING VP3000 AXIAL AIR MOVER is first turned on,

check for excessive vibration. If the unit vibrates exces-

sively or if blade rubs on housing turn off the unit immedi-

ately. Have a service technician inspect the unit to locate

the problem.

Motor Lubrication

Oil the unit every six months with 3 - 4 drops of SAE 20

weight non-detergent oil. Lubricate the motor with a drop

of oil after each washing.

IMPORTANT: The approved oil for lubrication is SAE 20

weight non-detergent oil, specifically designated for

use with electric motors.

Oil hole locations. Access the oil holes by removing the

protective grill(s) and turning the unit upside down. If user

adds oil, it is recommended to run unit for 5-15 minutes,

to remove excess oil from unit.

Cleaning The VP3000 Axial Air Mover

The VIKING VP3000 AXIAL AIR MOVER’Shousing is made of a

durable and washable polyethylene. When cleaning, the

use of solvents is NOT recommended.

When washing inside the unit, disconnect the unit from

its power source. Clean inner barrel, grills and blade. Wipe

down motor exterior with a damp cloth. If the motor gets

wet during cleaning, simply allow ample time for motor to

dry out completely before restarting. If you clean your

device frequently perform motor lubrication more frequently

as well.

If you wash the VIKING VP3000 AXIAL AIR MOVER and do not

plan to use it within 24 hours, allow the fan to drip dry for

10 minutes and then run the VIKING VP3000 AXIAL AIR MOVER

for 3 - 5 minutes before storing it.

Replacement Parts and Optional Accessories

Contact the factory at 1-800-533-7533 to order replace-

ment parts, or optional accessories

4025204 Switch, Rocker, On-Off-On

4025206 Grill, Safety, Intake

4025207 Grill, Safety, Exhaust

4025460 Axial Air Mover Stand

4025299 Stand Hardware Kit

VIKING VP3000 AXIAL AIR MOVER with FOCUS™Technology Owners Manual 5

Viking VP3000 Axial Air Mover

Wiring Diagram

and maximizes the air velocity across the floor and along

the wall when placed the at 4.5° angle from the wall.

By touching the front edge of the output side of the

VIKING VP3000 AXIAL AIR MOVER against the wall and rotating

the rest of the unit against the wall, the restoration profes-

sional will place the VIKING VP3000 AXIAL AIR MOVER at 4.5°

due to the housing’s built-in design. A VIKING VP3000 AXIAL

AIR MOVER properly positioned at 4.5° will achieve high

velocity airflow in the corner, on the carpet, and along the

wall while also increasing air throw distances. Higher

angles should only be used on the rare occasion air flow up

the wall is desired. Recent testing shows the largest drying

area has been produced by a 22°angle. Refer to Figure 5A.

VP3000 AXIAL AIR MOVER Applications

Sizing VIKING VP3000 AXIAL AIR MOVER’S

for Water Restoration Jobs

Current industry standards call for one axial air mover per

12-16 linear feet of wall space, dependent upon the Class

of water damage. For commercial structures, the industry

standard calls for one air mover for every 50-60 ft2.

The water restoration industry based these estimates on

the air mover technology available when writing the

standards. Following these equipment-sizing standards

when using the VIKING VP3000 AXIAL AIR MOVER will result in

dramatically faster drying times. If the restoration

professional desires to merely achieve industry standard

drying times, he can use fewer VIKING VP3000 AXIAL AIR

MOVERS than current equipment standards allow.

Placement of the VP3000 AXIAL AIR MOVER

Current industry guidelines suggest placing air movers at

a 45° angle to wall. These guidelines apply to air movers

without FOCUS Technology. FOCUS Technology allows the

restoration professional to place the VIKING VP3000 AXIAL

AIR MOVER at an angle more parallel to the wall.

The test graph shown in Figure 4 depicts immediate air

flow at the FOCUS Technology corner and delivery of two

times the evaporative drying air velocity of existing units.

The FOCAL POINT sustains this air flow for more than 20 feet

Figure 5A: Placement

of FOCAL POINT shown at

4.5° and 22°. Use

4.5° position to maxi-

mize air velocity and

22°position to maxi-

mize drying area.

2500

2000

1500

1000

500

0 Feet 5 10 15 20 25

Air Velocity (fpm)

Figure 4: Airflow of the PHOENIX AXIAL AIR MOVER

measured 3.5” parallel to wall.

Patent pending FOCUSTM Technology

delivers two times the evaporative

drying air velocity of existing

air movers.

Immediate

Air Flow

6VIKING VP3000 AXIAL AIR MOVER with FOCUS™Technology Owners Manual

WARRANTOR:

Therma-Stor LLC

PO Box 8680

Madison, WI 53708

Telephone: 1-800-533-7533

WARRANTY: This warranty covers VIKING

VP3000 AXIAL AIR MOVERS.

Year One - 100% parts and labor (all components)

Year Two - 100% parts only (all components)

Year(s) Three through Seven - Only materials

and workmanship of the housing are covered.

If a defect in materials or workmanship occurs

within the warranty period, Therma-Stor LLC will

repair or replace the defect.

USER RESPONSIBILITIES: Warranty service

must be performed by a servicer authorized by

Therma-Stor LLC. To obtain warranty service you

must obtain a return material authorization

(RMA). To obtain an RMA you must present proof

of purchase or (lease), by use of a warranty card,

original sales receipt or other reasonable and

reliable means.

To obtain an RMA call Therma-Stor LLC at the

above number and ask for the ThermaStor Inc.

Service Department, which will then issue an

RMA number and arrange for, at our option,

either repair or replacement.

FREIGHT: Freight to and from the servicer is

the responsibility of the end-user. The end-user

is responsible for normal care and proper return

packaging.

LIMITATIONS AND EXCLUSIONS: This warranty

does not cover any defect, malfunction, etc.

resulting from misuse, abuse, lack of normal

care, corrosion, freezing, tampering, modifica-

tion, unauthorized or improper repair or installa-

tion, accident, acts of nature or any other cause

beyond Therma-Stor LLC's reasonable control.

If any VIKING VP3000 AXIAL AIR MOVER part is

repaired or replaced, the new part shall be

warranted for the balance of original warranty

(but all warranty periods will be extended by the

period of time, if any, that the VIKING VP3000 AXIAL

AIR MOVER with FOCUS Technology is out of service

while awaiting covered warranty service).

Warranty service will be performed during normal

working hours.

UPON THE EXPIRATION OF THE WRITTEN

WARRANTY APPLICABLE TO THE VIKING VP3000

AXIAL AIR MOVER OR ANY PART THEREOF, ALL

OTHER WARRANTIES IMPLIED BY LAW,

INCLUDING MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, SHALL ALSO

EXPIRE. ALL WARRANTIES MADE BY THERMA-

STOR LLC ARE SET FORTH HEREIN, AND NO

CLAIM MAY BE MADE AGAINST THERMA-STOR

LLC BASED ON ANY ORAL WARRANTY. IN NO

EVENT SHALL THERMA-STOR LLC, IN CONNEC-

TION WITH THE SALE, INSTALLATION, USE, REPAIR

OR REPLACEMENT OF ANY VIKING VP3000 AXIAL

AIR MOVER OR PART THEREOF BE LIABLE UNDER

ANY LEGAL THEORY FOR ANY SPECIAL, INDIRECT

OR CONSEQUENTIAL DAMAGES INCLUDING WITH-

OUT LIMITATION WATER DAMAGE (THE END

USER SHOULD TAKE PRECAUTIONS AGAINST

SAME), LOST PROFITS, DELAY, OR LOSS OF USE

OR DAMAGE TO ANY REAL OR PERSONAL PROP-

ERTY.

Some states do not allow limitations on how

long an implied warranty lasts, and some do

not allow the exclusion or limitation of incidental

or consequential damages, so one or both of

these limitations may not apply to you.

LEGAL RIGHTS: This warranty gives you specific

legal rights, and you may also have other rights

which vary from state to state.

VIKING VP3000 AXIAL AIR MOVER Limited Warranty

Beliebte Luftaufbereiter Handbücher anderer Marken

Klimor

Klimor EVO-S Bedienungsanleitung

Salda

Salda SMARTY XP Leitfaden

BLAUBERG

BLAUBERG KOMFORT Roto EC S400 Bedienungsanleitung

Trenton

Trenton TPLP Series Bedienungsanleitung

Kemper

Kemper CleanAirTower Bedienungsanleitung

Daikin

Daikin DV PTC 14 Series Bedienungsanleitung

Haier

Haier HB2400VA1M20 Bedienungsanleitung

Webasto

Webasto BlueCool A-Series Bedienungsanleitung

RDZ

RDZ DA 701 Technisches Dokument

Carrier

Carrier 39T Abmessungen und Installationsanleitung

Armstrong Air

Armstrong Air BCE5V Series Bedienungsanleitung

ActronAir

ActronAir CAY500T Bedienungsanleitung

Carrier

Carrier 40MBDAQ Bedienungsanleitung

Allied

Allied A93UH1E Bedienungsanleitung

Nortek

Nortek B6VMAI Bedienungsanleitung

TemperZone

TemperZone Econex Pro OPA 1410RLTM4FPQD Wartungs- und Serviceanleitung

RDZ

RDZ WHR 200 Technisches Dokument

AAON

AAON H3 Series Betriebsanleitung