Viking VK200Z Bedienungsanleitung

Viking VK200Z

Zoom Led Profile

__________________

User Manual

1. Overview

Technical Parameters:

• LED POWER: 200W

• LED Colour: cool white 200w COB LED

• IC Chip :Epistar

• LED Life Time: over 10,000 hours

• Colour Rendering Index(CRI): Ra≥90

• Voltage :AC90-260V 50-60Hz Auto sensing

• Max power consumption : 250w

• Beam angle: Zoom from 15° to 38°

• Dimmer :0~100% linearly adjustable

• Strobe :1-25 times/sec

• Refresh Rate:>400 Video Flicker Free

• Focus: Manual adjusted by hand

• Technology: High-quality glass optical system , Glass reflector

• Control protocol: DMX 512

• Control System: DMX, Auto run and Master/Slave

• DMX Channels: 1/3 Channels

• DMX In and Out on 3 pin and 5 pin XLR

• Working Temperature: -30 to 45 degrees Centigrade

• Housing: Aluminium

• Cooling System: All Copper Radiator & very low noise fan (one fan)

• Thermal Sensor Monitoring: Over-temperature Protection

• Externally fused: 20mm 5a Quick Blow

• IP Grade: IP20

• Powercon In and Out Connectors

• Net Weight: 8.8 kg

• Lantern size: 60 x 27 x 39 cm

• Carton Packing Size: 80 x 31 x 31 cm

2. Operation

Using the UP and DOWN buttons you can increase or decrease values in the LED menu. Once

the desired value has be achieved it is important to press ENTER in order to save the value.

On Power up if no DMX data is present or the DMX cable is not plugged in then the display will

Flash to indicate lack of data. Once data is being received the display will cease flashing.

After a short delay the display will auto turn off to avoid distraction in the theatre environment. To

Turn the display back on simply press any of the display buttons.

The unit can be mounted in any direction and the display can be inverted for ease of use.

Focusing the unit is done by loosening the focus 2 Knobs either side of the lens tube. It is possible to

give a slight twist to the lens tube to focus a gobo which has become distorted through use. Once in focus,

lock off the focus knobs.

Make sure in use that the unit is not covered up by curtains scenery or such like which would restrict the

Airflow through the unit - powerful LED light engines such as this one do get hot and require a constant

Flow of air to radiate the heat away from the unit.

Gobos can be used in this unit with the VK200GB holder that accepts industry standard B size gobos.

These are placed in the holder and can be rotated and locked in position with the simple screw fixing

supplied. This unit is particularly suited to gobo projection with it’s crisp glass optics.

The unit can be used without a controller and can be daisy chained for use in a master / slave scenario.

The master unit is set to the brightness/strobe levels required by all the salves and will automatically

Sync with them if no DMX is present. For this to happen all addresses on the head must be set to DMX of 1

The Red LED Display will turn off after no button has been pressed for 30 seconds - to turn back on just

press any button. The display can also be inverted - see menu options overleaf.

The cooling Fan in the unit will automatically start to spin when the unit reaches 40 degree centigrade

and will increase as the heat rises further.

2.2. Menu Data

Main Menu Sub Menu Function Operation Remark

No sub menu A = 3 Channel

DMX Mode

UP/DOWN Adjust the DMX

start address

ENTER Save the DMX

start address

No sub menu D = 1 Channel

DMX Mode

UP/DOWN Adjust the DMX

start address

ENTER Save the DMX

start address

Two Sub menus StAt = Static

Mode

ENTER Enter sub menu

C: Colour (White) UP/DOWN Adjust the

brightness of the

light (from 0 to

255)

ENTER Save the

brightness level

St = Strobe UP/DOWN Adjust the strobe

flash rate (0=off

20= fastest)

ENTER Save the strobe

speed level

Two Sub menus Temperature ENTER Enter temperature

options

Current

Temperature

ENTER Enter 2nd sub

T=Top UP/DOWN Change the value

of maximum

working

temperature

Set protect

temperature

ENTER Save value

No sub menu diSP = Display ENTER Reverse LED

Display

orientation

No sub menu RESt = Reset ENTER Reset the unit to

default settings

On entering the reset option above the display will show …. (4 dots) = you must then enter a password

Which is UP/DOWN/UP/DOWN & ENTER the display will then briefly show YES and the unit will

Reset to default settings.

2.3. DMX Channel Data

2.3.1. Standard channel mode : Display shows A.001

DMX

Channel

Value Funct Rema

1 0~255 dimmer

2 0~10 default delay of dimmer

11~15 no dimmer delay

16~255 Choose delay of dimmer 16 is the shortest delay time, increasing

gradually.... to 255 - the longest delay time

3 0~10 no strobe

11~255 speed of strobe (255 is fastest)

2.3.2. Basic channel model : Display shows D.001

Channel Value Function

1 0~255 dimmer

SAFETY WARNING

1. Warning

Every person involved with the installation , operation and maintenance of this device has to be

Experienced or qualified .

Users must follow the instructions of this manual

Unqualified person can not open the housing cover and operate the device , or the dealer will not accept

liability for any resulting defects or problems. There are no user servicable parts inside the light.

Protect the device against rain and moisture, it is for INSIDE use only

2. Warning notes :

Power supply : AC 100V-240V , 50/60Hz auto sensing

Make sure the power switch is off , the power plug , outlet and the earth connection is in good

condition before connecting the device with the mains.

During moving and installation , make sure the device is not damaged against metal parts and other

tough materials.

The minimum distance between light-output and the illuminated surface must be more than 50cm

The device must only be installed on a non-flammable surface. In order to safeguard sufficient ventilation,

leave 50cm of free space around the device . Please note that heat-sensitive objects may be deformed or

damaged by the emitted heat.

During operation the housing becomes very hot ! Do not operate the device for 15 minutes after switching off .

The maximum ambient temperature Ta = 45° C must never be exceeded , The maximum housing

temperature Tb=80° C must never be exceeded .

For indoor use

Replace any visible cracked protective shield , filters and lens .

The protective shield, filters and lens will require weekly cleaning as smoke fluid tends to building up

residues reducing the light output very quickly.

Unit C4 Rhombus Park

Diamond Road

Norwich

Norfolk NR6 6NN

Tel: 01603 401982

Inhaltsverzeichnis

Andere Viking DJ-Equipment Handbücher

Viking

Viking VK300F Bedienungsanleitung

Viking

Viking VK3010 Bedienungsanleitung

Viking

Viking VK10 Bedienungsanleitung

Viking

Viking VK1430 Pixelcyc Bedienungsanleitung

Viking

Viking Le Maitre Freezing Pro Bedienungsanleitung

Viking

Viking VK440 Super FLX Bedienungsanleitung

Viking

Viking VK1218 UL Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung