Viking Designer DDFB304 Bedienungsanleitung

Viking Installation Guide

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

Freestanding Bottom-Mount/

French Door Bottom-Mount

Refrigerator/Freezer

Listed

IIMMPPOORRTTAANNTTSSAAFFEETTYYIINNSSTTRRUUCCTTIIOONNSS

YYoouurrssaaffeettyyaannddtthheessaaffeettyyooffootthheerrssiissvveerryyiimmppoorrttaanntt..

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others. All safety messages will be

preceded by the safety alert symbol and the word “DANGER” , “WARNING” or “CAUTION”.

These words mean:

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions

are not followed.

Immediate hazards which WWIILLLLresult in severe personal injury or death

Hazards or unsafe practices which CCOOUULLDDresult in severe personal injury or death.

DANGER

WARNING

To reduce the risk of fire, electric shock, serious injury or death when using your refrigerator, follow these basic

precautions, including the following:

Hazards or unsafe practices which CCOOUULLDDresult in minor personal injury or property damage.

CAUTION

WARNING

•Read all instructions before using the refrigerator.

•Observe all local codes and ordinances. Install refrigerator according to Installation Instructions. All connections for

water, electrical power and grounding must comply with local codes and be made by licensed personnel when

required.

•Do not modify plug on power cord. If plug does not fit electrical outlet, have proper outlet installed by a qualified

technician. Replace worn power cords and/or loose plugs.

•Do not ground to a gas line or cold-water pipe.

•Do not remove warning tag from power cord

•Refrigerator is designed to operate on a separate 115 volt, 15 amp., 60 cycle line.

•Do not tamper with refrigerator controls.

•Do not service or replace any part of refrigerator unless specifically recommended in Use & Care or Installation

Instructions. Do not attempt service if instructions are not understood or if they are beyond personal skill level.

•Always disconnect refrigerator from electrical supply before attempting to change light bulbs, clean, or service the

refrigerator. Disconnect the power cord by grasping the plug, not the cord.

•Always read and follow manufacturer’s storage and ideal environment instructions for items being stored in refrigerator.

•Never allow children to operate, play with, crawl inside or stand on any part the refrigerator.

•Never clean refrigerator parts with flammable fluids. The fumes can create a fire hazard or explosion.

•Clean up spills or water leakage associated with water installation.

•Keep your refrigerator in good condition. Bumping or dropping refrigerator can damage refrigerator or cause

refrigerator to malfunction or leak. If damage occurs, have refrigerator checked by qualified service technician.

--SSAAVVEETTHHEESSEEIINNSSTTRRUUCCTTIIOONNSS--

GGEENNEERRAALLIINNFFOORRMMAATTIIOONN

IIMMPPOORRTTAANNTT--PPLLEEAASSEERREEAADDAANNDDFFOOLLLLOOWW

Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, and

amperage is attached to the product.

To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by qualified

people in accordance with all applicable codes and standards, including fire-rated construction.

The installer should leave these instructions with the consumer who should retain them for local inspector’s use and for

future reference.

BBAASSIICCSSPPEECCIIFFIICCAATTIIOONNSSAANNDDDDIIMMEENNSSIIOONNSS

FFrreeeessttaannddiinnggBBoottttoommMMoouunntt//FFrreenncchhDDoooorrBBoottttoommMMoouunntt

DDEESSCCRRIIPPTTIIOONNVVCC//DDDDBBFF//VVCC//DDDDFFFF

Overall Width 35 5/8” (90.5 cm)

Addition of side panels: 35 7/8” (91.1 cm)

Overall Height from Bottom 70 1/8” (178.1 cm)

Addition of tops/grilles: 71 7/8” (182.6 cm)

Overall Depth from Rear To front of door: 26 3/4” (67.9 cm)

Cutout Width 36” (91.4 cm)

Cutout Height 70 1/2” (179.0 cm)

Addition of tops/grilles 72” (182.9 cm)

Cutout Depth 24” (61.0 cm)

Electrical Requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3-prong

plug attached to product.

Maximum Amp Usage 7.9 amps

Inlet Water Requirements 1/4” copper tubing inlet waterline; minimum 35 psi; maximum 100 psi

Overall Interior Capacities Bottom Mount French Door Bottom Mount

•Refrigerator 14.4 cu. ft. (407 liters) 14.1 cu. ft. (399 liters)

•Freezer 5.5 cu. ft. (156 liters) 5.5 cu. ft. (156 liters)

•Total Capacity 19.9 cu. ft. (563 liters) 19.6 cu. ft. (555 liters)

Approximate Shipping Weight 327 lbs. (148.7 kg)

DANGER

RRiisskkooffCChhiillddEEnnttrraappmmeenntt

BBEEFFOORREEYYOOUUTTHHRROOWWAAWWAAYYYYOOUURROOLLDD

RREEFFRRIIGGEERRAATTOORROORRFFRREEEEZZEERR::

•Take off the doors.

•Leave the shelves in place so that children

may not easily climb inside.

IIMMPPOORRTTAANNTT::Child entrapment and

suffocation are not problems of the past.

Junked or abandoned refrigerators are still

dangerous... even if they will sit for “just a few

days.”

IIttiisstthheeccuussttoommeerr’’ssrreessppoonnssiibbiilliittyyttoo::

•contact a qualified electrical installer.

•assure that the electrical installation is adequate and in conformance with the National Electrical Code, ANSI/NFPA

70-latest edition or Canadian Electrical Code C22.1-1998 and C22.2 No. 0-M91 (or latest edition), and all local codes

and ordinances. (115 volt, 60-Hz, 15 amp, fused, electrical supply is required. It is required that a separate circuit

serving only this appliance be provided. This appliance is equipped with a power supply cord having a 3-prong

grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, grounding-

type wall receptacle. If a 2-prong receptacle is encountered, the customer must contact a qualified electrical installer

to have it replaced with a properly grounded 3-prong receptacle. Do not use an extension cord or adapter plug.)

EELLEECCTTRRIICCAALLSSHHOOCCKKHHAAZZAARRDD

PPlluuggiinnttooaaggrroouunnddeedd33--pprroonnggoouuttlleett..

DDOONNOOTTrreemmoovveeggrroouunnddpplluugg..

DDOONNOOTTuusseeaannaaddaapptteerr..

DDOONNOOTTuusseeaanneexxtteennssiioonnccoorrdd..

FFaaiilluurreettooffoolllloowwtthheesseeiinnssttrruuccttiioonnss

ccoouullddrreessuullttiinnffiirreeoorreelleeccttrriiccaallsshhoocckk..

WARNING

Power cord with 3-prong

grounding plug

Grounding-type wall

receptacle

**WWhheenniinnssttaalllliinnggiinnttooaaccuuttoouutt,,tthheeeeddggeeoofftthheeddoooorrmmuussttbbee2277//88””((77..33ccmm))ffrroommtthheeaaddjjaacceennttccoouunntteerrttooppccaabbiinneett..

IINNSSTTAALLLLAATTIIOONN

Your refrigerator was packed carefully for shipment. Remove and discard all packaging and tape. Do not remove the

model/serial number label.

LLooccaattiioonn

•Do not install refrigerator near oven, radiator or other heat source. If not possible, shield refrigerator with cabinet

material.

•Do not install where the temperature falls below 55oF (13oC) or rises above 110oF (43oC). Malfunction may occur at

these temperatures.

•Refrigerator is designed for indoor household application only.

MMeeaassuurriinnggtthheeOOppeenniinngg

When installing your refrigerator, measure carefully. Allow 1/2” (1.3 cm) space at top and 1/2” (1.3 cm) behind the

machine compartment cover (located in the rear) for proper air circulation. Sub-flooring or floor coverings (i.e. carpet,

tile, wood floors, rugs) may make your opening smaller than anticipated. Some clearance may be gained by using the

leveling procedure under “LEVELING”.

TTrraannssppoorrttiinnggYYoouurrRReeffrriiggeerraattoorr

•NNEEVVEERRtransport refrigerator on its side. If an upright position is not possible, lay refrigerator on its back. Allow

refrigerator to sit upright for approximately 30 minutes before plugging it in to assure oil returns to the compressor.

Plugging the refrigerator in immediately may cause damage to internal parts.

•Use an appliance dolly when moving refrigerator. AALLWWAAYYSStruck refrigerator from its side or back - NNEEVVEERRfrom its

front.

•Protect outside finish of refrigerator during transport by wrapping cabinet in blankets or inserting padding between

the refrigerator and dolly.

•Secure refrigerator to dolly firmly with straps or bungee cords. Thread straps through handles when possible. Do not

overtighten. Overtightening restraints may dent or damage outside finish.

DDoooorraannddDDrraawweerrRReemmoovvaall

Some installations require door/drawer removal to transport the refrigerator to its final location.

DANGER

To avoid electrical shock which can cause severe personal injury or

death, observe the following:

•Disconnect power to refrigerator before removing doors or drawer.

Connect power only after replacing doors or drawer.

•Green ground wire must be attached to top hinge while performing

door removal and replacement.

•Tape decorative panels (select models) securely into place before

removing door handles.

CAUTION

To avoid damage to walls and flooring observe

the following:

•Protect vinyl or other flooring with cardboard,

rugs or other protective material, prior to

moving refrigerator.

•DDooNNoottadjust refrigerator to be any shorter

than 68 1/2” tall (minus hinge and cap). Doing

so may damage underside components.

BBoottttoommMMoouunnttDDoooorrRReemmoovvaall

1. Unplug power cord from power source.

2. Remove toe grille.

3. Remove top hinge cover from refrigerator door by removing

Phillips screw and retain screw and cover for later use.

4. Unscrew 5/16” hex head screws from top hinge to remove hinge

and retain all screws for later use.

5. Lift refrigerator door from center hinge pin.

6. Remove plastic sleeve, if present.

7. See page 6 for drawer removal instructions

FFrreenncchh--DDoooorrBBoottttoommMMoouunnttDDoooorrRReemmoovvaall

1. Unplug power cord from power source.

2. Remove toe grille.

3. Remove top hinge covers from refrigerator

doors by removing Phillips screw and retain

screw and cover for later use.

4. Unscrew 5/16” hex head screws from top hinge

to remove hinge and retain all screws for later

use.

5. Lift right side refrigerator door from center hinge

pin. Remove door closure from center hinge pin

on the right side and retain for later use.

6. Disconnect wire harness on top of left side

refrigerator door top hinge. Release two-pin

connector by pressing junction point with a flat

blade screwdriver or fingernail. Green ground

wire remains attached to the hinge.

7. Unscrew 5/16” hex head screws from top

hinge to remove hinge and retain all screws

for later use. Lift left side refrigerator door,

along with top hinge, from center hinge pin.

8. Remove phillips screws to remove right and

left hinges and retain

all screws for later

use.

Right

side

door

closure

IINNSSTTAALLLLAATTIIOONN

PPuulllloouuttFFrreeeezzeerrDDrraawweerrRReemmoovvaall

DANGER

To prevent accidental child entrapment or suffocation risk,

do not remove the divider in the top freezer basket.

CAUTION

To avoid possible injury, product, or property damage,

you will need two people to perform the following

instructions.

1. Pull drawer open to full extension.

2. Tilt the lower basket forward and lift to remove.

3. Lift top of drawer front to unhook the drawer

from the slides. Lift door front out to remove

1. Pull both rails out to full extension.

2. While supporting door front, hook supports into slots

located on inside of each slide.

3. Lower door front into final position.

4. Place the basket cradles back onto the drawer slides.

5. Tilt the lower basket front down and set it down into the

basket cradles.

IINNSSTTAALLLLAATTIIOONN

NNOOTTEE::All four drawer

bracket supports must

be in the proper slots

for the drawer to

function properly.

PPuulllloouuttFFrreeeezzeerrDDrraawweerrRReeiinnssttaallllaattiioonn

BBoottttoommMMoouunnttDDoooorrRReeiinnssttaallllaattiioonn

Install hinge assemblies

1. Install top hinge loosely with 5/16” hex head screws.

2. Install center hinge with phillips screws.

3. Place hinge side of refrigerator door on center hinge pin.

4. While holding refrigerator door upright, tighten down top hinge with 5/16” hex head driver and replace hinge cover.

FFrreenncchh--DDoooorrBBoottttoommMMoouunnttDDoooorrRReeiinnssttaallllaattiioonn

1. Install hinge assemblies. Install center hinge with phillips screws.

2. Place hinge side of refrigerator door on center hinge pin. Install top hinge with

5/16” hex head screws.

3. While holding refrigerator door upright, tighten down top hinge with 5/16” hex

head driver.

4. Reconnect two-pin connector.

5. Replace top hinge covers.

IINNSSTTAALLLLAATTIIOONN

OOppeenniinnggaannddCClloossiinnggtthheeRReeffrriiggeerraattoorrDDoooorrss--FFrreenncchh--DDoooorrBBoottttoommMMoouunnttMMooddeellss

CCoonnnneeccttiinnggtthheeWWaatteerrSSuuppppllyy

Your new refrigerator is uniquely designed with two

refrigerator doors. Either door can be opened or closed

independently of one another. There is a vertically-hinged

section on the left fresh food door. When the left door is

closed, the hinged section automatically forms a seal

between the two doors when both doors are closed. When

the left door is opened, the hinged seal automatically folds

inward so that it is out of the way.

WARNING

To avoid electrical shock which can cause severe personal

injury or death, DDOONNOOTTattempt to remove the hinged

seal from the fresh food section.

CAUTION

To avoid possible product damage, AALLWWAAYYSSverify that

the hinged seal is folded against the edge of the door

prior to closing.

WARNING

To reduce the risk of injury or death, follow basic

precautions including the following:

•Do not attempt installation if instructions are not

understood or if they are beyond personal skill level.

•Do not service ice maker

•Observe all local codes and ordinances.

•Water damage due to an improper water connection

may cause mold/mildew growth. Clean up spills or

leakage immediately.

CAUTION

To avoid property damage or possible injury, follow basic

precautions, including the following:

•Consult a plumber to connect 1/4” OO..DD..ccooppppeerrttuubbiinnggto

household plumbing to assure compliance with local codes

and ordinances.

•Confirm water pressure to water valve is between 35 and 100

pounds per square inch, 20 pounds per square inch without

a filter.

•Do not use a self-piercing, or 3/16” saddle valve. Both

reduce water flow, can become clogged over time, and may

cause leaks if repair is attempted.

•Tighten nuts by hand to prevent cross threading. Finish

tightening nuts with pliers and wrenches. DO NOT

overtighten.

•Wait two to three hours before placing refrigerator into final

position to check and correct any water leaks. Recheck for

leaks after 24 hours.

•Verify the copper tubing under the sleeve is smooth and free

from defects. Do not reuse an old sleeve

MMaatteerriiaallssNNeeeeddeedd

•1/4” outer diameter flexible copper tubing

•Shut-off valve (requires a 1/4” hole to be drilled into

water supply line before valve attachment)

•(2) Adjustable wrenches

•1/4” hex nut driver

NNOOTTEE::

•Use copper tubing only for installation. Plastic is less durable and can cause damage.

•Add 8 feet to tubing length needed to reach water supply for creation of service loop.

CCoonnnneeccttiinnggtthheeWWaatteerrSSuuppppllyy

IINNSSTTAALLLLAATTIIOONN

1. Create service loop with copper tubing ( minimum 2 feet

diameter). Avoid kinks in the copper tubing when

bending the service loop. Do not use plastic tubing. See

figure 1

2. Remove plastic cap from water valve inlet port. See figure

3. Place brass nut (A) and sleeve (B) on copper tube end as

illustrated. RReemmeemmbbeerr::Do not use old sleeve. The nut

and the sleeve are provided in the consumer literature

packet. See figure 3

4. Place end of copper tubing into water valve inlet port.

Shape tubing slightly. Do not kink - so that tubing feeds

straight into inlet port. See figure 4.

5. Slide brass nut over sleeve and screw nut into inlet port.

Place adjustable wrench on nut “1” attached to plastic

waterline and maintain position. Using second adjustable

wrench, turn the lower nut “2” counterclockwise and fully

tighten the upper nut in place. IIMMPPOORRTTAANNTT::Do not

overtighten. Cross threading may occur. See figure 5

6. Pull on tubing to confirm connection is secure. Connect

tubing to frame with tubing clamp (C) and turn on water

supply . See figure 6. Check for leaks and correct if

necessary. Continue to observe the water supply

connection for two or three hours prior to moving the

refrigerator to its permanent location.

7. Monitor water connection for 24 hours. Correct leaks, if

necessary.

Figure 1

Figure 2 Figure 3

Figure 4 Figure 5 Figure 6

2 feet diameter

minimum

CAUTION

To protect property and refrigerator from damage, observe the following:

•Protect vinyl or other flooring with cardboard, rugs, or other protective material.

•Do not use power tools when performing leveling procedure.

To enhance the appearance and maintain performance, the refrigerator should be

level.

NNOOTTEE::Complete any required panel installation and/or water supply connection

before leveling. Refrigerator should be in permanent location prior to leveling.

1. Remove toe grille. Grasp firmly and pull outward to unclip. See figure 7.

2. Using hex head driver, turn the front adjustment screws “A” on each side to

raise or lower the front of the refrigerator.

3. Using the hex head driver, turn each of the adjustment screws “B” to raise or

lower the rear of the refrigerator.

4. Using the carpenter’s level, make sure front of refrigerator is 1/4” (.06 cm) or

approximately 1/2 bubble higher than back of refrigerator and that the

refrigerator is level from side to side.

5. Turn stabilizing legs “C” clockwise until firmly against floor.

6. Turn adjustment screws “A” counterclockwise to allow the full weight of the

refrigerator to rest on the stabilizing legs.

7. Replace the toe grille. Align the toe grille mounting clips with the lower cabinet

slots. Push the toe grille firmly until it snaps into place.

MMaatteerriiaallssNNeeeeddeedd

•3/8” hex head driver

•Carpenter’s level

Figure 7

AABBAA

LLeevveelliinngg

SSOOUUNNDD

CClliicckkiinngg

AAiirrrruusshhiinnggoorr

wwhhiirrrriinngg

GGuurrgglliinnggoorr

bbooiilliinnggssoouunndd

TThhuummppiinngg

VViibbrraattiinnggnnooiissee

BBuuzzzziinngg

HHuummmmiinngg

HHiissssiinnggoorr

ppooppppiinngg

PPOOSSSSIIBBLLEECCAAUUSSEE

• Freezer control clicks when starting or stopping compressor.

• Motorized device sounds like an electric clock and snaps in and

out.

• Freezer fan and condenser fan make this noise while operating.

• Evaporator and heat exchanger refrigerant makes this noise

when flowing.

• Ice cubes from ice maker (select models) drop into ice bucket.

• Compressor makes a pulsating sound while running.

• Refrigerator is not level.

• Ice maker water valve hookup (select models) buzzes when ice

maker fills with water.

• Ice maker is in the ‘on’ position without water connection.

• Compressor can make a high-pitched hum while operating.

• Defrost heater hisses, sizzles or pops when operational.

SSOOLLUUTTIIOONN

• Normal operation

• See Installation Instructions

for details on how to level

your refrigerator.

• Normal operation

• Stop sound by raising ice

maker arm to OFF position

• Normal operation

OOPPEERRAATTIINNGGSSOOUUNNDDSS

PPrroobblleemmPPoossssiibblleeCCaauusseeWWhhaattTTooDDoo

Freezer control and lights Refrigerator is in defrost mode. Normal operation. Wait 40 minutes to see if compressor restarts.

are on, but compressor

is not operating

Temperature-controlled Control settings are too low. See use and care manual to adjust controls.

drawers are too warm Freezer controls are set too low. See use and care manual to adjust controls.

Drawer is improperly positioned. See use and care manual to verify drawer positioning.

Refrigerator does not Refrigerator is not plugged in. Plug in refrigerator.

operate Touch temperature controls are set to “OFF”. See use and care manual to set controls.

Fuse is blown or circuit breaker needs to Replace any blown fuses.

be reset. Check circuit breaker and reset, if necessary.

Power outage has occurred . Call local power company to report outage.

Refrigerator still will not Refrigerator is malfunctiong . Unplug refrigerator and

operate transfer food to another refrigerator. If another refrigerator is not

available, place dry ice in freezer section to preserve food.

Warranty does not cover food loss. Contact service for

assistance.

Food temperature Condenser coils are dirty. Clean coils according to use and care manual.

is too cold Refrigerator or freezer controls are set too Properly adjust controls.

high.

Food temperature is too Door is not closing properly. Check for internal obstructions that are keeping door from is too

warm closing properly.

Refrigerator is not level.

See installation instructions for details on how to level your

refrigerator. Check gaskets for proper seal, clean if necessary.

Controls need to be adjusted. See use and care manual to adjust your controls.

Condenser coil is dirty. Clean coils according to use and care manual.

Rear air grille is blocked. Check the positioning of food items in refrigerator to make sure

grille is not blocked. Rear air grilles are located under produce

drawers.

Door has been opened frequently , or has Reduce the time door is open. Organize food items efficiently

been opened for long periods of time. to assure door is open for as short a time as possible.

Food has recently been added. Allow time for recently added food to reach refrigerator or

freezer temperature.

TTrroouubblleesshhoooottiinngg

Andere Handbücher für Designer DDFB304

Dieses Handbuch passt für folgende Modelle

Andere Viking Gefrierschrank Handbücher

Viking

Viking DFFB536L Montageanleitung

Viking

Viking Professional DFFB530 Bedienungsanleitung

Viking

Viking FDFB5301R Montageanleitung

Viking

Viking Professional VCFB530 Bedienungsanleitung

Viking

Viking VIFB530LSS Montageanleitung

Viking

Viking DFUR144 Benutzerhandbuch

Viking

Viking FDFB5301R Leitfaden

Viking

Viking Quiet Cool VCFB5301 Bedienungsanleitung

Viking

Viking Designer DDFB304 Bedienungsanleitung

Viking

Viking Designer DDFB364 Bedienungsanleitung

Viking

Viking FDFB5361R Montageanleitung

Viking

Viking DDFB Bedienungsanleitung

Viking

Viking Designer DFBB363 Bedienungsanleitung

Viking

Viking DDFB530 Series Bedienungsanleitung

Beliebte Gefrierschrank Handbücher anderer Marken

Siemens

Siemens GU..D SERIES Bedienungsanleitung

Omcan

Omcan FR-CN-0155 Bedienungsanleitung

Beko

Beko FNE290E24W Bedienungsanleitung

Electrolux

Electrolux ARCTIS G 8 60 50-6I Bedienungsanleitung

Electrolux

Electrolux EUF2042AOX Bedienungsanleitung

Dometic

Dometic CoolFreeze CFX95DZ Bedienungsanleitung

Electrolux

Electrolux EUF7000W1 Bedienungsanleitung

Polar Electro

Polar Electro CT330 Bedienungsanleitung

MPM

MPM MPM-145-SK Series Bedienungsanleitung

SAF

SAF PRESTOTIG 200AC/DC Kurzanleitung

Zanussi

Zanussi ZFT11407WA Bedienungsanleitung

AEG

AEG A63190GT Bedienungsanleitung

AEG

AEG A81000TNW0 Bedienungsanleitung

Matsui

Matsui MUC50S15E Bedienungsanleitung

NEFF

NEFF G4344X8 Bedienungsanleitung

Frigidaire

Frigidaire FV 1246 H Bedienungsanleitung

Frigidaire

Frigidaire FFC13K1AW Bedienungsanleitung

Electrolux

Electrolux EU 2400C Bedienungsanleitung