Viking VGBQ030-2T Bedienungsanleitung

GGAASSCCOONNVVEERRSSIIOONN

TTooccoonnvveerrttaaggrriillllffrroommnnaattuurraallttooLLPP//PPrrooppaanneeggaassoorrLLPP//PPrrooppaanneettoo

nnaattuurraall,,yyoouummuussttuusseetthheeccoonnvveerrs

siioonnkkiittssuupppplliieeddbbyytthheemmaannuuffaaccttuurreerr..

WWhheennccoonnvveerrttiinnggttooNNaattuurraallGGaass,,uusseetthheeTTNNKKVVGGBBQQkkiittffoorrVVGGBBQQ

mmooddeellssaannddTTNNKKVVGGIIQQkkiittoorrVVGGIIQQmmooddeellss..WWhheennccoonnvveerrttiinnggttoo

LLPP//PPrrooppaannee,,uusseetthheeTTLLPPKKVVGGBBQQkkiittffoorrVVGGBBQQm

mooddeellssaannddTTLLPPKKVVGGIIQQ

kkiittffoorrVVGGIIQQmmooddeellss..CCoonnvveerrssiioonnsssshhoouullddoonnllyybbeeddoonneebbyyaann

aauutthhoorriizzeeddsseerrvviicceetteec

chhnniicciiaann..

NNOOTTEE::WWHHEENNTTHHEECCOONNVVEERRSSIIOONNIISSCCOOMMPPLLEETTEEDD,,TTHHEE

CCOONNVVEERRSSIIOONNLLAABBEELLMMUUSSTTBBEEPPLLAACCEEDDNNEEXXTTTTOOTTHHEERRA

ATTIINNGG

LLAABBEELLUUNNDDEERRTTHHEEDDRRIIPPTTRRAAYYIINNTTHHEERREEAARRLLEEFFTTCCOORRNNEERRNNEEXXTT

TTOOTTHHEEIINNLLEETTPPIIPPEE..

INSTALLATION

INSTRUCTIONS

VVGGBBQQ““TT””//VVGGIIQQ““TT””SSEERRIIEESSCCOONNVVEERRSSIIOONNKKIITT

VIKING RANGE CORPORATION

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

IIMMPPOORRTTAANNTT::PPLLEEAASSEERREEAADDAANNDDFFOOLLLLOOWW

1. Before beginning, please read these instructions completely and

carefully.

2. Do not remove permanently affixed labels, warnings, or plates from

product. This may void the warranty.

3. Please observe all local and national codes and ordinances.

CCAAUUTTIIOONN::Before proceeding with the conversion, shut off the gas

supply to the appliance prior to disconnecting the

electrical power.

WARNING

This conversion kit shall be installed by a

qualified service agency in accordance with the

manufacturer’s instructions and all applicable

codes and requirements of the authority having

jurisdiction. If the information in these

instructions is not followed exactly, a fire,

explosion or production of carbon monoxide

may result causing property damage, personal

injury or loss of life. The qualified service

agency is responsible for the proper

installation of this kit. The installation is not

proper and complete until the operation of the

converted appliance is checked as specified in

the manufacturer’s instructions supplied with

the kit.

TTNNKK--VVGGBBQQCCoonnvveerrssiioonnKKiittPPaarrttLLiisstt

((11))NNaattuurraallRReegguullaattoorrAAsssseemmbbllyy

((11))NNaattuurraallOOrriiffiicceeKKiitt

((44))##4400G

GrriillllBBuurrnneerrOOrriiffiicceess

((22))##5511SSmmookkeerrBBuurrnneerrOOrriiffiiccee

((22))##4499SSiiddeeBBuurrnneerrOOrriiffiieess

((22))##4488IInnffrraarreeddBBuurrn

neerrOOrriiffiicceess

((11))NNaattuurraallCCoonnvveerrssiioonnKKiittLLaabbeell

((11))FF2200112222CCoonnvveerrssiioonnKKiittIInnssttaallllaattiioonnIInnssttrruuccttiioonnss

TTLLPPKK--VVGGBBQQCCoonnvveerrssiioonnKKiittPPaarrttLLiisstt

((11))LLPP//PPrrooppaanneeRReegguullaattoorrAAsssseemmbbllyy

((11))LLPP//PPrrooppaanneeOOrriiffiicceeKKiitt

((44)

)##5544GGrriillllBBuurrnneerrOOrriiffiicceess

((22))##6622SSmmookkeerrBBuurrnneerrOOrriiffiiccee

((22))##5577SSiiddeeBBuurrnneerrOOrriiffiicceess

((22))##5577IInnffrraar

reeddBBuurrnneerrOOrriiffiiccee

((11))LLPP//PPrrooppaanneeCCoonnvveerrssiioonnKKiittLLaabbeell

((11))FF2200112222CCoonnvveerrssiioonnKKiittIInnssttaallllaattiioonnIInnsst

trruuccttiioonnss

TTNNKK--VVGGIIQQCCoonnvveerrssiioonnKKiittPPaarrttLLiisstt

((11))NNaattuurraallRReegguullaattoorrAAsssseemmbbllyy

((11))NNaattuurraallOOrriiffiicceeKKiitt

((33))##4400GGr

riillllBBuurrnneerrOOrriiffiicceess

((22))##5511SSmmookkeerrBBuurrnneerrOOrriiffiiccee

((22))##4499SSiiddeeBBuurrnneerrOOrriiffiieess

((22))##4488IInnffrraarreeddBBuurrnne

errOOrriiffiicceess

((11))TTrruuSSeeaarrTTMMIInnffrraarreeddBBuurrnneerrVVaallvvee

((11))NNaattuurraallCCoonnvveerrssiioonnKKiittLLaabbeell

((11))FF2200112222CCoonnvveerrssiioonnKKiittIInnssttaallllaattiioonnIInnssttr

ruuccttiioonnss

TTLLPPKK--VVGGIIQQCCoonnvveerrssiioonnKKiittPPaarrttLLiisstt

((11))LLPP//PPrrooppaanneeRReegguullaattoorrAAsssseemmbbllyy

((11))LLPP//PPrrooppaanneeOOrriiffiicceeKKiitt

((33)

)##5544GGrriillllBBuurrnneerrOOrriiffiicceess

((22))##6622SSmmookkeerrBBuurrnneerrOOrriiffiiccee

((22))##5577SSiiddeeBBuurrnneerrOOrriiffiicceess

((22))##5577IInnffrraar

reeddBBuurrnneerrOOrriiffiiccee

((11))TTrruuSSeeaarrTTMMIInnffrraarreeddBBuurrnneerrVVaallvvee

((11))LLPP//PPrrooppaanneeCCoonnvveerrssiioonnKKiittLLaabbeell

((11))FF2200112222CCoonnvveerrssiioonnKKiittIInnssttaallllaattiioonnIIn

nssttrruuccttiioonnss

TTooccoonnvveerrtttthheerroottiissssiieerreeiinnffrraarreeddbbuurrnneerr::

1. Remove the back cover from

the unit to expose the orfice

hood to the infrared burner.

2. Remove the gas orifice hood

located on the grill.

3. Replace with the gas orifice

hood supplied in the

conversion kit.

4. Replace the back cover

Orifice hood

Back

Cover

Landing ledge

Grill Burner /

Side Burner

Orifice hoods

RReeaarrssiiddeeooff

ccoonnttrrooll

ppaanneell

Smoker Burner

Orifice hood

TTooccoonnvveerrttggrriillllbbuurrnneerrss,,ssiiddeebbuurrnneerraannddssmmookkeerrbbuurrnneerr::

1. Remove all grates, flavor generators and stainless steel

burners from the unit.

2. Look into the burner box back toward the control panel in

order to located the orifice hoods. Remove the gas orifice

hoods located on the grill burner valves.

3. Replace the orifice hoods with the correct gas orifice hoods

supplied in the conversion kit. (See chart)

4. Replace the stainless steel burners, flavor generators and

grates.

NNOOTTEE::For installation in areas with altitudes greater than 2000 feet, the orifices must be derated at 4% for every

1000 feet above 2000 feet.

Natural LP/Propane

Orifice Hood Orifice Hood

Infrared (2) - #48 (2) - #57

Burner

Natural LP/Propane

Orifice Hood Orifice Hood

Grill

Burners (4) - 40 (4) - #54

Smoker

Burners (2) - #51 (2) - #62

Side

Burners (2) - #49 (2) - #57

VGBQ “T” SERIES CONVERSIONS

TToocchheecckkLLPP//PPrrooppaanneettooNNaattuurraallCCoonnvveerrssiioonnoofftthheerroottiissssiieerree

iinnffrraarreeddbbuurrnneerr::

Ignite the rotissere burner and set it to low. If the burner will not

hold a flame, it will be necessary to adjust the low setting. Remove

the control panel to expose the rotissiere safety valve. Using a small

flat head screwdriver turn the adjustment screw counterclockwse.

Visually check the flame. When the burner is able to hold a flame

on the low setting, the setting is complete. Replace the control

panel.

adjustment

screw

TTooccoonnvveerrtttthheerroottiissssiieerreeiinnffrraarreeddbbuurrnneerr::

1. Remove the back cover from the unit to

expose the orfice hood to the infrared

burner.

2. Remove the gas orifice hood located on

the grill.

3. Replace with the gas orifice hood supplied

in the conversion kit.

4. Replace the back cover

Orifice hood

Back

Cover

TTooccoonnvveerrttggrriillllbbuurrnneerrss,,TTrruuSSeeaarrTTMMbbuurrnneerr,,ssiiddeebbuurrnneerraannddssmmookkeerrbbuurrnneerr::

1. Remove all grates, flavor generators and stainless steel burners from the

unit except for ones over TruSearTM infrared burner.

2. Remove control panel to expose the burner valves. Remove the orifice

hoods located on the valve for the grill burners, side burners, and

smoker burner.

3. Replace the orifice hoods with the correct gas orifice hoods supplied in

the conversion kit for the grill burners, side burners, and smoker burners.

The complete burner valve will have to be replaced on the TruSearTM

infraredd burner. (See chart)

4. Replace the stainless steel burners, flavor generators and grates.

NNOOTTEE::For installation in areas with altitudes greater than 2000 feet, the orifices must be derated at 4% for every

1000 feet above 2000 feet.

Natural LP/Propane

Orifice Hood Orifice Hood

Infrared (2) - #48 (2) - #57

Burner (20”)

Natural LP/Propane

Orifice Hood Orifice Hood

Grill

Burners (3) - 40 (3) - #54

Smoker

Burners (2) - #51 (2) - #62

Side

Burners (2) - #49 (2) - #57

TruSearTM

Infrared Burner (1) - #35 (1) - #51

VGIQ “T” SERIES CONVERSIONS

TToocchheecckkLLPP//PPrrooppaanneettooNNaattuurraallCCoonnvveerrssiioonnoofftthheerroottiissssiieerree

iinnffrraarreeddbbuurrnneerr::

With the control panel off, Ignite the rotissere burner and set it to

low. If the burner will not hold a flame, it will be necessary to adjust

the low setting. Remove the control panel to expose the rotissiere

safety valve. Using a small flat head screwdriver turn the adjustment

screw counterclockwse. Visually check the flame. When the burner

is able to hold a flame on the low setting, the setting is complete.

Replace the control panel.

adjustment

screw

Side Burner

Valves

(if applicable)

Rotissiere

Burner Valve Grill

Burner Valve

Smoker

Burner Valves

TruSearTM

Burner Valve

FFrroonnttooffuunniitt

wwiitthhccoonnttrrooll

ppaanneellrreemmoovveedd

LLEEAAKKTTEESSTTIINNGG

Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas tightness

check must be performed at the installation due to possible mishandling in shipment or excessive pressure unknowingly being

applied to the unit. Periodically check the whole system for leaks, or immediately check if the smell of gas is detected.

1. Do not smoke while leak testing. Extinguish all flames.

2. Never leak test with an open flame.

3. Make a soap solution of one part liquid detergent and one part water. You will need a spray bottle, brush or towel to apply

the solution to the fittings.

4. Check that all control knobs are in the “OFF” position.

5. Blowing bubbles in the soap solution indicates that a leak is present.

6. Stop a leak by tightening the loose joint or by replacing the faulty part with a replacement part recommended by the

manufacturer.

7. If you are unable to stop a leak, shut off the gas supply and call an authorized gas appliance service technician or

LP/Propane gas dealer. Do not use the grill until the leak is corrected.

8. After checking for leaks, push in and turn any control knob to release the pressure in the hose and manifold. Turn off the

control knob.

NNaattuurraalloorrLLPP//PPrrooppaanneeCCoonnnneeccttiioonn

Fixed Connection: Standard Residential 1/2” gas service line - 1/2” NPT male with 3/8” flare adapter.

LP/Propane Cylinder Connection: 1/2” NPT male with 3/8” flare adapter

Operating Pressure: 4.0 W.C.P. Natural or 10.0” W.C.P. LP/Propane

Supply Pressure: Natural gas - 6” to 14” W.C.P. If in excess of 14” W.C.P., a step down regulator is required.

LP/Propane - 11” to 14” W.C.P. If in excess of 14” W.C.P., a step down regulator is required.

The installer must check the supply pressure and operating pressure. To check operating pressure, remove one burner and

hook a manometer to the orifice hood. Ignite one of the remaining burners and turn the valve for the removed burner to high.

Read the pressure on the manometer.

Check with your local gas utility company or with local codes for instructions on installing gas supply lines. Be sure to check on

type and size of run, and how deep to bury the line. If the gas line is too small, the unit will not function properly. Any joint

sealant used must be an approved type and be resistive to the actions of natural gas.

Leak Test Points

BBUURRNNEERRAADDJJUUSSTTMMEENNTT

Each burner is tested and adjusted at the factory prior to shipment; however, variations in the local gas supply may

make it necessary to adjust the burners. The flames of the burners (except the rotisserie infrared and TruSearTM infrared burner)

should be visually checked and compared with Fig. 1, Fig. 2, and Fig. 3.

Flames should be blue and stable with no yellow tips, excessive noise or lifting. If any of these conditions exist, check

if the air shutter or burner ports are blocked by dirt, debris, spider webs, etc. With a proper flame height, adjust the air shutter

to obtain a blue flame with no yellow tipping that sits on the burner at the burner ports. The air shutter is locked in place by a

set screw which must be loosened prior to lighting the burner for adjustments.

To access the air shutter on the grill burners and smoker burner, remove the valve panel. To access the air shutter on

the side burners, remove the grates, burner bowls, and grate support. With a screw driver, loosen the lock-screw on the face

of the air shutter. Light the burner and adjust according to the directions below.

1. If the flame is yellow, turn the air shutter counter clockwise to allow more air to the burner.

2. If the flame is noisy and lifting away from the burner, turn the air shutter clockwise to reduce the amount of air to

the burner.

Once adjusted, turn the burner off, tighten the set screw on the air shutter, replace the valve panel for the grill burners and the

grate support, burner bowls, and grates for the side burners.

To ensure proper installation of the grill burners, side burners, and smoker burner:

1. Slide opening in air shutters over the orifice located in the front of the grill.

2. For the smoker burner, secure back of the burner by placing over screw slot on rear of grill and replacing screw.

IINNIITTIIAALLIIGGNNIITTIIOONNOOFFBBUURRNNEERRSS

All burners are tested before leaving the factory. Field adjustments may be necessary for proper mixture of gas

and air for proper operation. When the grill is connected to the gas service, it should be adjusted by a qualified

technician. For lighting instructions, refer to the Outdoor Gas Grill Use and Care Manual.

Orifice

½”

(1.3 cm)

3/8”

(.95 cm)

Air

Shutter

FFiigg..11

GGRRIILLLLBBUURRNNEERR

Air Shutter

Orifice

3/8” (.95 cm)

1 1/2”

(3.8 cm)

NNaattuurraallLLPP//PPrrooppaannee

Grill Burners 25,000 BTU 22,500 BTU

Smoker Burner 12,500 BTU 11,250 BTU

Side Burners 15,000 BTU 13,500 BTU

Rotissiere Infrared Burner 15,000 BTU 13,500 BTU

TruSearTM Infrared Burner 30,000 BTU 30,000BTU

BURNER RATINGS

SSppaarrkkIIggnniittoorrAAddjjuussttmmeenntt

Occasionally a burner may not ignite within a few seconds after

turning the appropriate control knob counter-clockwise. To adjust

the spark ignitor, use a small needle nose plier to turn the metal

head of the ignitor towards the port (opening) on the burner. DDOO

NNOOTTTTUURRNNTTHHEEIIGGNNIITTOORRBBYYTTHHEECCEERRAAMMIICCBBAASSEE..This could

cause damage to the spark ignitor.

Metal head

on ignitor

Ports (openings)

on burner

Ceramic Base

FFiigg..33

SSIIDDEEBBUURRNNEERR

((IIffaapppplliiccaabbllee))

FFiigg..22

SSMMOOKKEERRBBUURRNNEERR

((IIffaapppplliiccaabbllee))

33//88””(.95 cm)

¼” (.64 cm)

Air Shutter

Orifice

DDiissttaanncceebbeettwweeeenniiggnniittoorr

aannddbbuurrnneerr--33//1166””(.45 cm)

Distance between

ignitor and burner

port - 1/8” (.32 cm)

Viking Range Corporation

111 Front Street •Greenwood, Mississippi 38930 USA•(662) 455-1200

Specifications subject to change without notice.

For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com

F20122A (PS0404VR)

Andere Handbücher für VGBQ030-2T

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viking Grillzubehör Handbücher

Viking

Viking QSC200SS Bedienungsanleitung

Viking

Viking 100 Series Bedienungsanleitung

Viking

Viking BQC1300SS Technisches Handbuch

Viking

Viking BQC300T3SS Bedienungsanleitung

Viking

Viking 100 Series Technisches Handbuch

Beliebte Grillzubehör Handbücher anderer Marken

FEUERHAND

FEUERHAND PYRON PLATE Bedienungsanleitung

STOK

STOK SIS1030 Bedienungsanleitung

Broil King

Broil King 60938 Bedienungsanleitung

BREEO

BREEO OutRig Post Bedienungsanleitung

Weber

Weber iGrill 3 Bedienungsanleitung

STOK

STOK SGA3070 Bedienungsanleitung

STOK

STOK SIS4000 Bedienungsanleitung

Kenmore

Kenmore 30800334/30611 Bedienungsanleitung

Kenmore

Kenmore 10478 Bedienungsanleitung

Landmann

Landmann AG-VI-103BKXX Bedienungsanleitung

Otto Wilde

Otto Wilde GRILL STAND Bedienungsanleitung

Charcoal Companion

Charcoal Companion Fire UP! Bedienungsanleitung

Ecco

Ecco ED5051 Series Bedienungsanleitung

GHP Group

GHP Group Dyna-Glo DG4WB Bedienungsanleitung

Bartscher

Bartscher KD-30 Bedienungsanleitung

Otto Wilde

Otto Wilde S90 Bedienungsanleitung

Dangrill

Dangrill 86307 Bedienungsanleitung

Weber

Weber IGRILL 2 Bedienungsanleitung