Viking VDUI5240 Bedienungsanleitung

Install / Use & Care

MANUAL

5 SERIES

Refrigerated Drawers

Tiroirs Réfrigérés

Gavetas Refrogeradas

VDUI5240

FR-D’installation/d’utilisation et d’entretien

ES-De instalación/operación y mantenimiento

NOTE

!CAUTION

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the anti-tip device .................................................6

Product dimensions ............................................................8

Using your Electronic control ............................................10

Starting your appliance ..................................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................10

Adjusting the temperature .............................................11

Temperature mode ........................................................11

Controllock....................................................................11

Temperature sensor error codes ....................................11

Alarms ...........................................................................12

Door (drawer) ajar.....................................................12

Power failure ............................................................12

Temperature alarm ...................................................12

Vacationmode................................................................13

Care and cleaning .............................................................13

Energy saving tips ............................................................14

Obtaining service .............................................................14

Troubleshooting ................................................................15

Warranty ...........................................................................16

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could

result in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

CONTENTS

!WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

NOTE

!CAUTION

!WARNING

XXXXXXXXXXXX

VIKING RANGE, LLC

GREENWOOD, MS 38930

UNPACKING YOUR APPLIANCE

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.vikingrange.com

The following information will be

required when registering your

appliance.

Service Number

Rev. Letter

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on

the serial plate which is located inside the cabinet on the

bottom of the liner toward the left side. Open the bottom

drawer to view it. See ﬁgure 1.

Warranty Registration

Online registration

available at

www.vikingrange.com

Figure 1

!WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

!CAUTION

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Rear

Leveling

Legs

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources.

To ensure your product performs to speciﬁcations, the

recommended installation location temperature range is

from 55 to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the

appliance. Keep this area open and clear of any

obstructions. Adjacent cabinets and counter top can be

installed around the appliance as long as the front grille

remains unobstructed.

Front Grille

Do not obstruct the front grille. The openings within

the front grille allow air to ﬂow through the condenser

heat exchanger. Restrictions to this air ﬂow will result in

increased energy usage and loss of cooling capacity. For

this reason it is important this area to not be obstructed and

the grille openings kept clean. Viking Range,LLC does not

recommend the use of a custom made grille as air ﬂow may

be restricted. (See Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the

appliance should be set so the unit is ﬁrmly positioned on

the ﬂoor and level from side to side and front to back. The

overall height of your appliance may be adjusted between

the minimum, 333⁄4" (85.7 cm), by turning the leveling leg in

(CW ↷) and the maximum, 343⁄4" (88.3 cm) by turning the

leveling leg out (CCW ↶).

To adjust the leveling legs, place the appliance on a solid

surface and protect the ﬂoor beneath the legs to avoid

scratching the ﬂoor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the

appliance forward using caution. On a level surface check

the appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille

adjusted to the desired height. When adjustment is

complete tighten the two front grille screws. (See Figure 5).

INSTALLING YOUR APPLIANCE

NOTE

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any

circumstances, be installed to an un-grounded

electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!WARNING

Ground Fault Circuit Interrupters (GFCI) are prone to

nuisance tripping which will cause the appliance to shut

down. GFCI’s are generally not used on circuits with power

equipment that must run unattended for long periods of

time, unless required to meet local building codes and

ordinances.

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must

be plugged into a mating grounding type receptacle

in accordance with the National Electrical Code and

applicable local codes and ordinances (see Figure 6). If the

circuit does not have a grounding type receptacle, it is the

responsibility and obligation of the customer to provide the

proper power supply. The third ground prong should not,

under any circumstances, be cut or removed.

Figure 6

Figure 5 Front grille screw

Front grille

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

Step by step instructions for locating the po-

sition of the bracket:

1) Decide where you want to place the drawer refrigerator.

Slide it into place, being careful not to damage the ﬂoor,

leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.

2) Raise the rear leveling legs approximately 1⁄4" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the refrigerator is in the desired location, then

mark on the ﬂoor the rear and side corner of the cabinet

where the anti-tip bracket will be installed. If the installation

does not allow marking the rear corner of the cabinet, then

make temporary lines on the ﬂoor marking the front corner

of the cabinet, excluding the drawer. Slide the refrigerator

out of the way. From the temporary line extend the sidewall

line back 211⁄2" (54.6 cm) as shown in Figure 8.

4) Align the anti-tip bracket to the marks on the ﬂoor so

the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 211⁄2" (54.6 cm) line (Rear of cabinet

line).

5) Fasten the anti-tip bracket to the ﬂoor using the supplied

screw. (See Figure 8).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Bottom View of

Refrigerated

Drawer Unit

Anti-Tip

Bracket Leveling Leg

Front of cabinet

211⁄2"

(54.6 cm)

Figure 7

!WARNING

• ALLAPPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE

INSTRUCTIONS BELOW

Floor Mount Installation

The anti-tip bracket is to be located on the ﬂoor in the left

or right rear corner of the refrigerator drawer as shown in

Figure 7.

!CAUTION

NOTE

Any ﬁnished ﬂooring should be protected with appropriate

material to avoid damage when moving the unit.

If installing on a concrete ﬂoor, concrete fasteners are

required, (not included with the anti-tip kit).

Anti-Tip Device

!WARNING

If your refrigerator is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the refrigerator is

removed from its location for any reason, make sure

that the device is properly engaged with the anti-tip

bracket when you push the refrigerator back into the

original location. If the device is not properly engaged,

there is a risk of the refrigerator tipping over, with the

potential for property damage or personal injury.

INSTALLING THE ANTI TIP DEVICE FOR FREESTANDING INSTALLATIONS

211⁄2"

(54.6 cm)

"V" notches

in bracket

"V" notches

in bracket

Figure 8

Rear of cabinet line

Figure 8a

Side of cabinet line

Front of cabinet line

Screw

Rear Leveling leg

"A"

"B"

"C"

"D"

"E"

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H"

VDUI5240 24"

(61 cm) **34" to 35"

(86.4 cm to 88.9 cm) *237⁄8"

(60.7 cm) 333⁄4" to 343⁄4"

(85.7 cm to 88.3 cm) 2323⁄32"

(60.2 cm) 267⁄32"

(66.6 cm) 395⁄32"

(99.5 cm)

Figure 9

Figure 9a

* Depth dimension of rough-in opening may vary depending on each individual installation. To recess entire

drawer "F" dimension plus 1" (2.5 cm) for thickness of power cord plug is required.

** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.

PRODUCT DIMENSIONS

Figure 10

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent

cabinet and the power cord routed through this

hole to a power outlet. Another way to increase

the available opening depth is to recess the power

outlet into the rear wall to gain the thickness of the

power cord plug. Not all recessed outlet boxes will

work for this application as they are too narrow,

but a recessed outlet box equivalent to Arlington

#DVFR1W is recommended for this application,

(see Figure 10).

"D"

"E"

"F"

"G"

"H"

Floor mount anti-tip bracket.

PRODUCT DATA

MODEL ELECTRICAL

REQUIREMENTS # PRODUCT

WEIGHT

VDUI5240 115V/60Hz/15A 130 lbs

(59 kg)

211⁄2"

(54.6 cm)

(2.5 cm)

WARNING

Floor mount Anti-tip Bracket must be installed for

freestanding applications. Not required for built in

applications.

Figure 11

PRODUCT DIMENSIONS

# A grounded 15 amp dedicated circuit is required.

Follow all local building codes when installing

electrical and appliance.

Power Failure ALARM RESET

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad Display Area Lock

keypad System Status

indicators

Figure 12

Electronic single zone control

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On"

position and will begin start-up of cooling as soon as power

is supplied. If the appliance does not start, conﬁrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic ﬁlm. This

ﬁlm may be removed by carefully lifting the ﬁlm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as

the appliance was powered-up at the factory for quality

inspection and then removed from power. A momentary

press of the "On/Off" keypad will reset this alarm condition.

(See Alarms section on page 12).

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the

temperature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel

will go dark with the exception of the system status "OK"

indicator which will remain enabled. Alarm conditions will

wake the display, (see alarms on page 12).

To make the following changes to the control

settings (turning the appliance ON/OFF, adjusting the

temperature, and activating vacation mode), the control

must be awake.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" keypad

until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conﬁrm tone will

sound, and the current storage compartment temperature

will be displayed.

USING YOUR ELECTRONIC CONTROL

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Viking LCD-Schublade Handbücher

Viking

Viking 5 Series Bedienungsanleitung

Beliebte LCD-Schublade Handbücher anderer Marken

Acnodes

Acnodes KD 8228 Bedienungsanleitung

Ameriwood

Ameriwood 9524328PCOM Bedienungsanleitung

Kesseböhmer

Kesseböhmer TANDEM solo Bedienungsanleitung

Crystal Image Technologies

Crystal Image Technologies RMD-151-A Series Bedienungsanleitung

APW Wyott

APW Wyott Ease Extreme HDX-1-120 Bedienungsanleitung

NTI

NTI RACKMUX-V17-N Bedienungsanleitung

Austin Hughes

Austin Hughes CyberView L120 Bedienungsanleitung

Uplift Desk

Uplift Desk STR018 Bedienungsanleitung

Acnodes

Acnodes KDC 81932 Bedienungsanleitung

Acnodes

Acnodes RK1200T Bedienungsanleitung

StarTech.com

StarTech.com DuraView RACKCONS1501 Bedienungsanleitung

Mocka

Mocka Mischa Bedienungsanleitung

GRASS

GRASS DWD XP Bedienungsanleitung

StarTech.com

StarTech.com DuraView RACKCONS1701 Bedienungsanleitung

Fisher & Paykel

Fisher & Paykel IZONA CoolDrawer RB36S Bedienungsanleitung

Synergy Global Technology

Synergy Global Technology LCD1U17-44 Bedienungsanleitung

Fujitsu

Fujitsu RC25 Bedienungsanleitung

Acnodes

Acnodes RK 1000B Bedienungsanleitung