Viking Designer DMOC205 Bedienungsanleitung
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
PARTS INCLUDED IN THE KIT
1) Frame Assembly 2) Bottom Duct Assembly
QTY 1
3) Screw A (1/2" length)
QTY 10
4) Screw B (1-3/4" length)
QTY 4
5) Screw C (3/4" length)
QTY 2
6) Duct A (1)
QTY 1
7) Duct A (2)
QTY 1
8) Duct A (3)
QTY 1
9) Duct B
QTY 1
10) Duct C
QTY 1
11) Template: QTY 1
Front Frame
QTY 1
Back Frame
QTY 1
INSTALLATION
INSTRUCTIONS
DESIGNER SERIES
CONVECTION MICROWAVE BUILT-IN TRIM KIT
Retain for Future Reference
IMPORTANT - PLEASE READ AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.
Remove the turntable from the oven cavity.
• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances.
• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future
reference.
THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING CONVECTION MICROWAVE OVENS SPECIFY-
ING BUILT-IN TRIM KIT DMTK276 OR DMTK306 FOR DESIGNER UNITS ON THE RATING LABEL ON THE BOTTOM
FACE PLATE OF THE OVEN CAVITY.
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
SCREW A
SCREW A
DUCT A-2
DUCT A-1
DUCT C
#1
DUCT B
SCREW A
SCREW A
18-11/16"
(47.5 cm)
24-7/8" (63.3 cm)
5"
(12.7 cm)
20-1/8"
(51.1 cm) 11-1/2"
(29.2 cm)
Illustration 1
Illustration 2
Illustration 3
SCREW A
DUCT A-1
DUCT BC SCREW A
Illustration 4
SCREW A
SCREW A
SCREW A
DUCT A-3
DUCT A-2
Illustration 5
2
CABINET OR WALL CUTOUT
Provide an opening in the wall or cabinet as indicated in
illustration 1. The depth should be a minimum of 20-1/8"
(51.1 cm). The floor of the opening should be constructed
of plywood strong enough to support the weight of the
oven (about 100 lbs.) and should be level for proper
operation of the oven .
NOTE: While the proper functioning of the oven does not
require that the opening be enclosed (with sides, ceiling
and rear partition), this may be required by local code,
and it is suggested that the local code be checked for
any such requirement.
ELECTRICAL OUTLET LOCATION
Outlet should NOT be in the shaded area as indicated
on illustration 1. At the rear of the opening, provide a
3-pronged, polarized, electrical outlet, 115-120 volt AC,
15 amp or larger.
EXHAUST DUCT ASSEMBLY
1. Insert the edge of DUCT (B) into the hold lip of DUCT
(C). Secure together by using a SCREW (A) provided in
the kit. Remove the existing screw (#1) at upper right
rear of the oven and secure DUCT (C) with the screw
(#1) just removed from the oven. Secure DUCT (B) with
SCREW (A) through the duct and into the original screw
hole in the oven. See illustration 2.
2. Position DUCT (A)-1 on the top of the oven inserting
edge of DUCT (BC) assembly into hole lip of DUCT
(A)-1. Tighten two SCREWS (A), securing DUCT (A)-1
to DUCT (BC) assembly. See illustration 3.
3. Position DUCT (A)-2 on the top of the oven and insert
it into the hold lip of DUCT (A)-1. Secure DUCT (A)-2
to DUCT (A)-1 using two SCREWS (A) provided. See
illustration 4.
4. Position DUCT (A)-3 on top of the oven and insert it
into DUCT (A)-2. Secure DUCT (A)-3 using three screws
(A) provided. See illustration 5.
Illustration 6
SCREW B
SCREW B
SCREW B
SCREW B
Illustration 9
Illustration 7
Illustration 8
BOTTOM DUCT
ASSEMBLY
FOOT
DUCT RECESS
NOTE: CENTER BOTTOM DUCT
ASSEMBLY IN THE OPENING
SCREW
BOTTOM
DUCT
ASSEMBLY
DETAIL A
SCREW C
GAP "A"
GAP "B"
3
MOUNTING TEMPLATE
1. Align the mounting template center line with the center
of the cutout and the floor line with the floor of the
cutout. Tape it into place.
2. For DMTK276, only predrill 4 holes marked “A” with
a 1/16" drill bit. For DMTK306, only predrill 4 holes
marked “B” with a 1/16" drill bit.
3. Remove template from the cabinet.
BOTTOM DUCT ASSEMBLY
1. Place the Bottom duct in the center of the opening so
that gap "A" is equal to gap "B". When the BOTTOM
DUCT ASSEMBLY is in the opening correctly, the
bottom flange will fit tightly against the lower edge of
the opening. See illustration 6.
2. Secure the BOTTOM DUCT ASSEMBLY with the two
(3/4") SCREWS (C). IMPORTANT: Secure screws using
holes on bottom flange.
CABINET INSTALLATION
1. Place the oven adjacent to the wall or cabinet opening.
Plug the power cord into the electrical outlet.
2. Carefully guide the assembled oven into the prepared
opening. Slide the oven on the BOTTOM DUCT
ASSEMBLY. See illustration 7. Avoid pinching the cord
between the oven and the wall. Adjust the position
of the oven so that the feet of the oven are fitted into
the holes of the BOTTOM DUCT ASSEMBLY. See
illustration 8.
FRAME INSTALLATION
Position the BACK FRAME to align with the predrilled
holes that were drilled with the mounting template. Check
that it is level and then secure with two SCREWS (B). See
illustration 9. Secure the bottom portion of the BACK
FRAME with the two remaining SCREWS (B).
Illustration 10
SNAP ATTACHMENT 2" (5.1 cm)
For 27" W and
30" W lower oven
MICROWAVE
CUTOUT
LOWER OVEN
CUTOUT
Illustration 11
FRAME INSTALLATION CONT. OVER OVEN INSTALLATION
TABS
Place the FRONT FRAME, with tabs on top, onto the
BACK FRAME. Secure the FRONT FRAME to the BACK
FRAME by firmly pushing the front frame onto the back
frame engaging the four (4) snap attachments. See
illustration 10.
Viking Range Corporation
111 Front Street • Greenwood, Mississippi (MS) 38930 USA • (662) 455-1200
Specifications subject to change without notice.
For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com
F20302A (PS0506VR)
TINSEB467MRR0
BASIC SPECIFICATIONS
Microwave Oven Built-In Designer Trim Kits
DMOC205 DMTK276 DMTK306
Overall Width 24-5/8" (62.5 cm) 26-9/16" (67.5 cm) 29-1/2" (74.9 cm)
Overall Height from Bottom 14-7/8" (37.7 cm) 19-13/16" (50.1 cm) 19-13/16" (50.1 cm)
Overall Depth from Rear 19" (48.3 cm) N/A
Oven Interior Width
Height
Depth
Overall
16-1/8"
9-5/8"
16-1/8"
1.5 cu. ft.
(40.9 cm)
(24.4 cm)
(40.9 cm) N/A
Cutout Width N/A Min. 24-7/8" (63.3 cm)
Cutout Height N/A Min. 18-11/16" (47.5 cm)
Cutout Depth N/A Min. 20-1/8" (51.1 cm)
Electrical Requirements 120VAC/60 Hz (UL)
117VAC/60 Hz (CSA) N/A
Max. Amp Usage 1.55 KW
1.5 KW
13 amps (UL)
13 (CSA) N/A
Approx. Shipping Wt. 60 lbs. (27.2 kg) 22.5 lbs. (10.2 kg) 24 lbs. (10.9 kg)
Andere Handbücher für Designer DMOC205
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Viking Mikrowellenofen Handbücher
Viking
Viking DrawerMicro Designer DMOD240SS Bedienungsanleitung
Viking
Viking VMOS201SS Kurzanleitung
Viking
Viking VMOS201SS Bedienungsanleitung
Viking
Viking RVMH330 Bedienungsanleitung
Viking
Viking VMOC206LE Bedienungsanleitung
Viking
Viking RDMOR200SS Bedienungsanleitung
Viking
Viking Designer DMOR205SS Bedienungsanleitung
Viking
Viking Professional VMOC205 Bedienungsanleitung
Viking
Viking RVMHC330 Bedienungsanleitung
Viking
Viking RDMOS201SS Bedienungsanleitung
Viking
Viking RVM320 Bedienungsanleitung
Viking
Viking Designer DMOR205SS Bedienungsanleitung
Viking
Viking RVMH330 Bedienungsanleitung
Viking
Viking VCSO210SS Bedienungsanleitung
Viking
Viking Professional VMOR205 Bedienungsanleitung
Viking
Viking RDMOR200SS Bedienungsanleitung
Viking
Viking VMOS501 Gebrauchsanweisung
Viking
Viking RDMOR206SS Bedienungsanleitung
Viking
Viking Professional VMOR205 Bedienungsanleitung
Viking
Viking DMOC205SS Bedienungsanleitung
