Vimar 21126 Benutzerhandbuch

21126

Electronic control with 8 inputs, 7 outputs, 3 modules.

Installer manual

Contents

1. General description......................................................................................................................................................................................................................4

2. Characteristics.............................................................................................................................................................................................................................4

3. Connections..................................................................................................................................................................................................................................4

3.1 Inputs.......................................................................................................................................................................................................................................4

3.2 Outputs....................................................................................................................................................................................................................................7

4. RGB LEDs and pushbuttons......................................................................................................................................................................................................10

4.1 RGB LEDs ............................................................................................................................................................................................................................10

4.2 Push buttons.........................................................................................................................................................................................................................10

5. Configuration of the device........................................................................................................................................................................................................11

5.1 Setting the colours of the LEDs.............................................................................................................................................................................................11

5.2 Device setup.........................................................................................................................................................................................................................11

5.3 Factory reset.........................................................................................................................................................................................................................12

6. Operation....................................................................................................................................................................................................................................13

6.1 Display of load status (feedback enabled)..............................................................................................................................................................................13

6.2 Without display of load status (feedback disabled).................................................................................................................................................................13

7. Installation rules.........................................................................................................................................................................................................................14

8. Regulatory compliance..............................................................................................................................................................................................................14

General description - Characteristics - Connections

1. General description

Electronic control with 6 independent pushbuttons, 8 non-polarised inputs, 7 solid state outputs for non-polarised contacts, conﬁgurable RGB LED backlighting, 9-32 Vdc

power supply, to be completed with Eikon Tactil labels and cover plate - 3 modules.

2. Characteristics

• Supply voltage: 9-32 Vdc SELV (insulated with double insulation on the power supply network)

• Max absorbed power in power supply input: 0.7 W

• Inputs:

- Input activation voltage: 5-32 Vdc

- Input activation current: 0.7-5.5 mA (according to input supply voltage)

- Signal frequency PWM input 7: 400 kHz (if you wish to change the current colour settings of the LEDs)

• Outputs:

- Voltage that can be controlled by the outputs: 40 V

- Current that can be controlled by each individual output: 100 mA

3. Connections

N.B. The conductors of the inputs and outputs can be extended up to at most 50 m (minimum section 0.33 mm2).

3.1 Inputs

The inputs connector is of the type JST PHDR-12VS.

30 cm

These are live inputs (they can be controlled directly using the supply voltage) and are all referred to the common contact of pin 11.

The inputs are non-polarised and can be activated with positive or negative currents, and therefore by push-pull, open collector, open-emitter or voltage-free contacts.

FRONT AND BACK VIEW

Configuration

buttons

Power supply

- +

Connector

inputs

Connector

outputs

9-32V

100mA

INPUTS

C IN

C OUT

OUTPUTS

Connections

• Wiring.

Input 1 (Orange)

Upper left pushbutton LED

Input 3 (Green)

Upper centre pushbutton LED

Input 5 (Purple)

Upper right pushbutton LED

Input 7 (White)

Colour of all LEDs in the device

Input 9 (Red)

Do not connect

Pin 11 (White/Red)

Inputs common

Input 2 (Pink)

Lower left pushbutton LED

Input 4 (Brown)

Lower centre pushbutton LED

Input 6 (Black)

Lower right pushbutton LED

Input 8 (Grey)

Select with or without feedback mode

Input 10 (Blue)

Do not connect

Pin 12 (Yellow)

Do not connect

Input 7 can be in PWM and this makes it possible to set the colours of all the LEDs of the device (see the paragraph "LED Conﬁguration").

3.1.1 Input connection

The inputs are not polarised and are isolated from the device's supply voltage by functional isolation (non-reinforced); this allows the connection of input signals

with reference voltages that differ from the supply voltage of the 21126 control, provided they have SELV power supplies.

A PWM signal can be connected to input 7.

Illustrated below are two examples of the wiring layouts that can be achieved.

Example 1: Connection via contacts that close to the power supply negative (-) (most frequently used case).

The inputs can be connected to the device's power supply negative (-) by means of a switch.

Open collector outputs of a third-party device can be used as switches (provided it is checked beforehand that these outputs have appropriate maximum voltage

and current values).

The inputs common is to be connected directly to the power supply positive (+).

9-32V

100mA

INPUTS

C IN

C OUT

OUTPUTS

C IN

–V

Connections

Example 2: Connection via contacts that close to the power supply positive (+) (the opposite to the previous example).

The inputs can be connected to the device's power supply positive (+) by means of a switch.

The inputs common is to be connected directly to the power supply negative (-).

9-32V

100mA

INPUTS

C IN

C OUT

OUTPUTS

–V

C IN

Example 3: Connection with a signal generator with different voltage references.

The inputs can be connected directly to a third-party device that provides an output with voltage and current values compatible with the inputs of the 21126

control.

The inputs common is to be connected directly to the negative (-) of the power supply of the third-party device.

9-32V

100mA

INPUTS

C IN

C OUT

OUTPUTS

–V(2)

–V

+V(2)

C IN

12V

Connections

3.2 Outputs

The outputs connector is of the type JST PHR-9.

30 cm

The outputs are non-polarised solid state (volt-free contact) and are all referred to the common on pin 9.

The outputs can be used to control signals but are not suitable for controlling loads (for example, thee coils of large relays or contactors, high-power LED lights, etc.).

• Wiring.

Output 1 (Orange)

Upper left pushbutton

Output 2 (Yellow)

Lower left pushbutton

Output 3 (Green)

Upper centre pushbutton

Output 4 (Blue)

Lower centre pushbutton

Output 5 (Purple)

Upper right pushbutton

Output 6 (Grey)

Lower right pushbutton

Output 7 (White)

Proximity sensor

Output 8 (Black)

Do not connect

Pin C (Red)

Outputs common

Output 7 activates when the proximity sensor is tripped.

3.2 1 Output connection

The outputs are not polarised and are isolated from the device's supply voltage by functional isolation (non-reinforced); this allows the connection of output signals

with reference voltages that differ from the supply voltage of the 21126 control, provided they have SELV power supplies.

Illustrated below are two examples of the wiring layouts that can be achieved.

Example 1: Connection with output contacts that close to the power supply negative (-) (most frequently used case).

The outputs can be connected to a third-party device with internal pull-up inputs.

The outputs common is to be connected directly to the power supply negative (+).

9-32V

100mA

INPUTS

C IN

C OUT

OUTPUTS

–V

C OUT

UPPER LEFT PUSHBUTTON

OUT 1

LOWER LEFT PUSHBUTTON

OUT 2

UPPER CENTRE PUSHBUTTON -

OUT 3

LOWER CENTRE PUSHBUTTON -

OUT 4

UPPER RIGHT PUSHBUTTON -

OUT 5

LOWER RIGHT PUSHBUTTON

OUT 6

PROXIMITY -

OUT 7

IN 1 -

UPPER LEFT PUSHBUTTON LED

IN 2 -

LOWER LEFT PUSHBUTTON LED

IN 3 -

UPPER CENTRE PUSHBUTTON LED

IN 4 -

LOWER CENTRE PUSHBUTTON LED

IN 5 -

UPPER RIGHT PUSHBUTTON LED

IN 6 -

LOWER RIGHT PUSHBUTTON LED

IN 7 - PWM SIGNAL (OPTIONAL)

IN 8 -

LOAD STATUS FEEDBACK

MODE (OPTIONAL)

COM. IN

COM OUT

+12VDC

Art. 01831.1

THIRD PARTY

AUTOMATION SYSTEM

(FOR EXAMPLE PLC, OR RMS)

OUTIN

OUT IN

Adj.

−V

INPUT:(输入):

OUTPUT:(輸出):

100-240VAC

0,5A 50/60Hz

12V

1,25A

10.8~13.8V

Max.1.25A

Max.15Watt

MEAN

WELL

“Terminal torque 4.4 Lb-in”

Connections

Example 2: Connection of small indicator lights.

The outputs can be connected to indicator lights with characteristics compatible with the maximum voltage and current values of the 21126 control.

The outputs common is to be connected directly to the power supply positive (+).

9-32V

100mA

INPUTS

C IN

C OUT

OUTPUTS

–V

C OUT

Connections

4. RGB LEDs and pushbuttons

4.1 RGB LEDs

The device is equipped with 6 RGB LEDs (the colours of the LEDs are conﬁgured via a signal on input 7 or via the local programming procedure) and the symbols dis-

played on the cover plate 21663 can be customised using the speciﬁc labels.

4.2 Pushbuttons

When the cover plate is not ﬁtted, the 21126 control presents six physical pushbuttons (shown in blue) and two conﬁguration pushbuttons (shown in red).

Once the cover plate has been ﬁtted to the control, the 6 touchscreen buttons (shown in blue) can be used independently of each other.

RGB LEDs and pushbuttons

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vimar Controller Handbücher

Vimar

Vimar Elvax EKKO ART 200D Bedienungsanleitung

Vimar

Vimar ELVOX EAM6.N Bedienungsanleitung

Vimar

Vimar by-me Eikon 20526 Bedienungsanleitung

Vimar

Vimar ELVOX KLYS ENM1 Bedienungsanleitung

Vimar

Vimar 03905 Bedienungsanleitung

Vimar

Vimar 01856 Bedienungsanleitung

Vimar

Vimar Eikon TACTIL Bedienungsanleitung

Vimar

Vimar Eikon Evo Well-contact Plus 21849 Bedienungsanleitung

Vimar

Vimar BY-ALARM PLUS 03824 Bedienungsanleitung

Vimar

Vimar Eikon Bedienungsanleitung

Vimar

Vimar ELVOX EAM2 Benutzerhandbuch

Vimar

Vimar ELVOX EKKO EAM1 Bedienungsanleitung

Vimar

Vimar Elvox EIM2 Bedienungsanleitung

Vimar

Vimar by-me Eikon 20549 Bedienungsanleitung

Vimar

Vimar Eikon 20581 Bedienungsanleitung

Vimar

Vimar by-me 01489 Bedienungsanleitung

Vimar

Vimar BY-ALARM PLUS 03823 Bedienungsanleitung

Vimar

Vimar SW230.T Bedienungsanleitung

Vimar

Vimar Eikon 20594.0 Bedienungsanleitung

Vimar

Vimar 09135.1.120 Bedienungsanleitung

Vimar

Vimar Elvox EIM2 Bedienungsanleitung

Vimar

Vimar EIKON 20594.0 Bedienungsanleitung

Vimar

Vimar by-me 02021 Bedienungsanleitung

Vimar

Vimar ESM4.120 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch