VIPA 134-4EE00 Bedienungsanleitung

Manual

VIPA System 100V

EM - Expansion modules

134-4Ex

Order No.: VIPA HB100E_EM

Reference: RE_134-4Ex

Rev. 08/23

This manual is part of the documentation package

with order number: VIPA HB100E_EM and relevant for:

Product Order number as of state:

HW FW

EM 134 VIPA 134-4Ex 01 -

Lerrzeichen

Manual VIPA System 100V About this Manual

Subject to change to cater for technical progress.

The information in this manual is supplied without warranties. Information is

subject to change without notice.

automatisierung mbH

Ohmstraße 4, D-91074 Herzogenaurach,

Tel.: +49 (91 32) 744 -0

Fax.: +49 (91 32) 744-144

Email: inf[email protected]

http://www.vipa.de

Hotline: +49 (91 32) 744-114

The content of this manual was carefully examined to ensure that it

conforms with the described hardware and software.

However, discrepancies can not be avoided. The specifications in this

manual are examined regularly and corrections will be included in

subsequent editions.

We gratefully accept suggestions for improvement.

VIPA, System 100V, System 200V, System 300V and System 500V

are registered trademarks of VIPA Gesellschaft für Visualisierung und

Prozessautomatisierung mbH.

SIMATIC, STEP and S7-300

are registered trademarks of Siemens AG.

Any other trademarks referred to in the text are the trademarks of the

respective owner and we acknowledge their registration.

Disclaimer of

liability

Trademarks

About this Manual Manual VIPA System 100V

Subject to change to cater for technical progress.

About this Manual

This manual describes the analog expansion module EM 134 of the

System 100V from VIPA.

Here you may find every information for commissioning and operation.

Chapter 1: Basics

These basics include recommendations on the handling of the modules of

the VIPA System 100V as central resp. decentral automation system.

Besides a system overview you will find general information of the System

100V like assembly dimensions, installation and environmental conditions.

The chapter is finished by the installation guidelines to ensure the EMC

during installation.

Chapter 2: Hardware description and deployment

This chapter contains every information for the deployment of the analog

expansion module of the System 100V.

Every Micro-PLC CPU has an interface for backplane bus connectors. This

allows to connect System 100V expansion modules and modules of the

System 200V family.

Outline

Manual VIPA System 100V Contents

HB100E - EM - RE_134-4Ex - Rev. 08/23 i

Contents

User considerations.................................................................................1

Safety information....................................................................................2

Chapter 1 Basics..............................................................................1-1

Safety information for Users.................................................................1-2

Overview System 100V........................................................................1-3

General Description of the System 100V..............................................1-4

Assembly dimensions...........................................................................1-5

Installation Guidelines..........................................................................1-7

Chapter 2 Hardware description and deployment.........................2-1

Assembly..............................................................................................2-2

Wiring the analog signals.....................................................................2-4

Structure ..............................................................................................2-6

Project engineering..............................................................................2-9

Analog value representation...............................................................2-15

Diagnostic data ..................................................................................2-20

Technical Data...................................................................................2-22

Appendix................................................................................................A-1

Index....................................................................................................A-1

Contents Manual VIPA System 100V

ii HB100E - EM - RE_134-4Ex - Rev. 08/23

Manual VIPA System 100V User considerations

HB100E - EM - RE_134-4Ex - Rev. 08/23 1

User considerations

This manual describes the installation, project engineering and usage of

the analog expansion module of the System 100V.

The manual is targeted at users who have a background in automation

technology and PLC programming.

This manual consists of chapters. Every chapter provides the description of

one specific topic.

This manual provides the following guides:

• An overall table of contents at the beginning of the manual

• An overview of the topics for every chapter

• An index at the end of the manual.

The manual is available in:

• printed form, on paper

• in electronic form as PDF-file (Adobe Acrobat Reader)

Important passages in the text are highlighted by following icons and

headings:

Danger!

Immediate or likely danger.

Personal injury is possible.

Attention!

Damages to property is likely if these warnings are not heeded.

Note!

Supplementary information and useful tips.

Objective and

contents

Target audience

Structure of the

manual

Guide to the

document

Availability

Icons

Headings

Safety information Manual VIPA System 100V

2 HB100E - EM - RE_134-4Ex - Rev. 08/23

Safety information

The System 100V is constructed and manufactured for

• communication and process control

• general control and automation tasks

• industrial applications

• operation within the environmental conditions specified in the technical

data

• installation into a cubicle

Danger!

This device is not certified for applications in

• explosive environments (EX-zone)

The manual must be available to all personnel in the

• project design department

• installation department

• commissioning

• operation

The following conditions must be met before using or commissioning

the components described in this manual:

• Modification to the process control system should only be carried out

when the system has been disconnected from power!

• Installation and modifications only by properly trained personnel

• The national rules and regulations of the respective country must be

satisfied (installation, safety, EMC ...)

National rules and regulations apply to the disposal of the unit!

Application

specifications

Documentation

Disposal

Manual VIPA System 100V Chapter 1 Basics

HB100E - EM - RE_134-4Ex - Rev. 08/23 1-1

Chapter 1 Basics

These basics include recommendations on the handling of the modules of

the VIPA System 100V as central resp. decentral automation system.

Besides a system overview you will find general information of the System

100V like assembly dimensions, installation and environmental conditions.

The chapter is finished by the installation guidelines to ensure the EMC

during installation.

Topic Page

Chapter 1 Basics..............................................................................1-1

Safety information for Users.................................................................1-2

Overview System 100V........................................................................1-3

General Description of the System 100V..............................................1-4

Assembly dimensions...........................................................................1-5

Installation Guidelines..........................................................................1-7

Overview

Content

Chapter 1 Basics Manual VIPA System 100V

1-2 HB100E - EM - RE_134-4Ex - Rev. 08/23

Safety information for Users

VIPA modules make use of highly integrated components in MOS-

technology. These components are extremely sensitive to over-voltages

that can occur during electrostatic discharges.

The following symbol is attached to modules that can be destroyed by

electrostatic discharges:

The symbol is located on the module, the module rack or on packing

material and it indicates the presence of electrostatic sensitive equipment.

It is possible that electrostatic sensitive equipment is destroyed by energies

and voltages that are far less than the human threshold of perception.

These voltages can occur where persons do not discharge themselves

before handling electrostatic sensitive modules and they can damage

components thereby, causing the module to become inoperable or

unusable. Modules that have been damaged by electrostatic discharges

may fail after a temperature change, mechanical shock or changes in the

electrical load.

Only the consequent implementation of protection devices and meticulous

attention to the applicable rules and regulations for handling the respective

equipment can prevent failures of electrostatic sensitive modules.

Modules have to be shipped in the original packing material.

When you are conducting measurements on electrostatic sensitive

modules you should take the following precautions:

• Floating instruments must be discharged before use.

• Instruments must be grounded.

Modifying electrostatic sensitive modules you should only use soldering

irons with grounded tips.

Attention!

Personnel and instruments should be grounded when working on

electrostatic sensitive modules.

Handling of

electrostatic

sensitive modules

Shipping of

electrostatic

sensitive modules

Measurements

and alterations on

electrostatic

sensitive modules

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VIPA Steuereinheit Handbücher

VIPA

VIPA System 200V IM Series Bedienungsanleitung

VIPA

VIPA System 200V PS Bedienungsanleitung

VIPA

VIPA SLIO FM 050-1BB30 Bedienungsanleitung

VIPA

VIPA CPU Series Bedienungsanleitung

VIPA

VIPA CPU 013C Bedienungsanleitung

VIPA

VIPA SLIO Series Bedienungsanleitung

VIPA

VIPA TM-E 900-1E630 Bedienungsanleitung

VIPA

VIPA CP143plus Bedienungsanleitung

VIPA

VIPA TM-E 900-1E650 Bedienungsanleitung

VIPA

VIPA 900-2H611 Bedienungsanleitung

VIPA

VIPA System 300S Bedienungsanleitung

VIPA

VIPA TM-E 900-1E660 Bedienungsanleitung

VIPA

VIPA TP 107-CL Bedienungsanleitung

VIPA

VIPA SLIO IM 053-1DN00 Bedienungsanleitung

VIPA

VIPA IM Series Bedienungsanleitung

VIPA

VIPA SPEED7 CPU 313SCDPM Bedienungsanleitung

VIPA

VIPA 2 SLIO System IM 053DP Bedienungsanleitung

VIPA

VIPA IM 306-1LZ00 Bedienungsanleitung

VIPA

VIPA System SLIO IM 053DN Bedienungsanleitung

VIPA

VIPA System 300S IM 353-1DP01 Bedienungsanleitung

VIPA

VIPA System 200V Series Bedienungsanleitung

VIPA

VIPA SLIO FM 050-1BB00 Bedienungsanleitung

VIPA

VIPA System 300S Bedienungsanleitung

VIPA

VIPA SLIO System FM 050-1BA10 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung