Virtualfly TQ6 Bedienungsanleitung
© 2021 Virtual Fly, SL
All trademarks and brand names are
trademarks or registered trademarks of their
respective owners. All rights reserved.
TQ6 & TQ6+
USER’S MANUAL
Rev 2.0 - September 2021
1. IN THE BOX
A) TQ6 / TQ6+
B) Clamp
C) Allen Screws
D) Allen Key
C. Maria Aurèlia Capmany, 21
P.I. La Fàbrica – 08297 Castellgalí (Spain)
Phone: (+34) 983 333 301
www.virtual-fly.com
For support visit help.virtual-fly.com
or contact us at support@virtual-fly.com
TQ6 & TQ6+ | User’s manual
2
2. HARDWARE SETUP
Two possible ways of setting up the included clamp are:
(1) on the backside or (2) on the bottom side. If setting the
clamp on the bottom side, make sure you unscrew the two
front rubber feet before.
Finally, connect the USB cable to the computer where the
flight simulation software is running.
TQ6 & TQ6+ | User’s manual
3
2.1. Changing the levers’ hardness
Your TQ6/TQ6+ oers the possibility to adapt the levers’
hardness to your preference.
You can do so by turning the knobs, K or J, as seen in the
picture, on the left and right sides of the TQ6/TQ6+. Once
you have adjusted the knobs, move all the levers, from top
to bottom, at the same time at least ten times.
K
J
TQ6 & TQ6+ | User’s manual
4
3. SOFTWARE SETUP
The TQ6/TQ6+ interacts with any computer as a joystick
(HID), so it is compatible with any flight simulation software.
Below, you have two options for setting up your TQ6/TQ6+
with the most popular flight simulation software: MSFS,
Prepar3D, and X-Plane.
3.1. Using VFHUB
VFHub is the software built by Virtual Fly to reduce the
complicated to the simple. It is the recommended software
setup for your TQ6/TQ6+. With VFHub, you can fly your
favorite flight simulation software without worrying about
configuring your Virtual Fly flight controls.
You can download the VFHub installer from https://www.
virtual-fly.com/downloads. The VFHub installer takes care of
installing VFHub together with all the required modules.
Connect the TQ6/TQ6+ to your computer, open VFHub,
and start flying right away. VFHub takes care of making your
TQ6/TQ6+ work with MSFS, Prepar3D, and X-Plane.
If your device is a TQ6, make sure to calibrate
the device in VFHub. For more details, check
the VFHub user’s manual at https://downloads.
virtual-fly.com/docs/vub/latest/VFHUB_USER’S_
MANUAL.pdf
If you use MSFS or X-Plane, set a blank profile to
the TQ6/TQ6+ in the controls or joysticks setup
menu before using your device. You can find the
detailed steps on how to set a blank profile here:
https://downloads.virtual-fly.com/docs/vub/ latest/
VFHUB_SET_BLANK_PROFILES.pdf
If you want to customize how your TQ6/TQ6+
works, make sure you read the VFHub user’s
manual available at https://downloads.virtual-fly.
com/docs/vub/latest/VFHUB_USER’S_MANUAL.
pdf for detailed instructions on all the tuning and
customization possibilities.
TQ6 & TQ6+ | User’s manual
5
3.2 Using an alternative joystick
configuration
Since the TQ6/TQ6+ interacts with any computer as a
joystick (HID), it is compatible with any flight simulation
software. Below, you have a general scheme for setting
up your TQ6/TQ6+ with the most popular flight simulation
software: MSFS, Prepar3D, and X-Plane.
MSFS
If you own a TQ6+, your device is ready to be used in MSFS.
If you have a TQ6, don’t worry, you only need to calibrate it
on Windows/MacOS/Linux first. Assign the axes inside the
controls menu, and the TQ6/TQ6+ will be ready to be used.
Finally, restart MSFS and verify that the device is configured
correctly. Please note that reverse zones do not work if you
do not use VFHub.
Prepar3D
If you own a TQ6+, your device is ready to be used in
Prepar3D. If you have a TQ6, don’t worry, you only need to
calibrate it on Windows/MacOS/Linux first. Open Prepar3D
and go to the controls menu. Inside, select the ‘TQ6/TQ6+’
from the devices list. Assign the axes as you please. Then
calibrate the device following the instructions.
Finally, restart Prepar3D and verify that the device is
configured correctly. Please note that reverse zones do not
work if you do not use VFHub.
X-Plane
If you own a TQ6+, your device is ready to be used in
X-Plane. If you have a TQ6, don’t worry, you only need
to calibrate it on Windows/MacOS/Linux first. Your TQ6/
TQ6+ needs to be calibrated inside X-Plane since axes are
automatically assigned. Open X-Plane, go to Configuration\
Joystick, and follow the calibration steps for your device.
Finally, restart X-Plane and verify that the device is configured
correctly. Please note that reverse zones need to be set up if
you do not use VFHub. Refer to the X-Plane manual to do so.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Virtualfly Controller Handbücher
