Vision ZL 7261 CL-5 Bedienungsanleitung

Federal Communications Commission Statement

This equipment has been followed to comply with Part 15 of the FCC Rules. This

equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try and correct the

interference by one of the following measures:

-Reorient or relocate the receiving antenna,

-Increase the separation between the equipment and receiver,

-Connect the equipment into and outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesirable operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate this

equipment.

Limited Warranty

Vision Guarantees that every wireless lighting module is free from physical defects

in material and workmanship under normal use for one year from the date of

purchase. If the product proves defective during this one-year warranty period,

Vision will replace it free of charge. Vision does not issue any refunds. This warranty

is extended to the original end user purchase only and is not transferable. This

warranty does not apply to: (1) damage to units caused by accident, dropping or

abuse in handling, or any negligent use; (2) units which have been subject to

unauthorized repair, taken apart, or otherwise modified; (3) units not used in

accordance with instruction; (4) damages exceeding the cost of the product; (5)

transit damage, initial installation costs, removal cost, or reinstallation cost.

For information on addional devices, plesae visit us at www.visionsecurity.com.tw

-5-

Operation Manual

ZL 7261 CL-5

ZL 7261 CN-5

ZL 7261 DE-5

ZL 7261 FR-5

ZL 7261 IT-5

ZL 7261 JP-5

ZL 7261 KR-5

ZL 7261 RU-5

ZL 7261 US-5

Z-Wave Power Monitor

ZL 7201 CL-5

ZL 7201 CN-5

ZL 7201 DE-5

ZL 7201 FR-5

ZL 7201 IT-5

ZL 7201 JP-5

ZL 7201 KR-5

ZL 7201 RU-5

ZL 7201 US-5

Z-Wave On/Off Module

ZL 7261/7201 V5

1050902 6B1Z-72003

Introduction

Thanks for choosing the Vision’s Power Monitor or On/Off Module of the home automation device. This

Power Monitor or On/Off Module is a Z-Wave TM enabled device (interoperable, two-way RF mesh

networking technology) and is fully compatible with any Z-Wave TM enabled network. Every main powered

Z-Wave TM enabled device acts as a signal repeater and multiple devices result in more possible

transmission routes, which helps eliminate “RF dead-sport”.

Z-Wave TM enabled devices displaying the Z-Wave TM logo can also be used with it regardless of the

manufacturer, and ours can also be used in other manufacturer’s Z-Wave TM enabled networks. This

module will send On/Off signal to the appliance that attached to this module by receiving Z-Wave TM

signal from controller or manually switch. It also sends the energy consumption (ZL7261 only) to the

controller when it requests. With special design, this module won’t interfere the other power outlet when

plug into the AC outlet. This module also acts as repeater (supporting FLiRS).

Product Description and Specification

Specification:

Package Content:

Protocol: Z-Wave

(ZM5202)

Frequency:

868.42 MHz (ZL7201CN/DE/FR/IT / ZL7261CN/DE/FR/IT)

869.00 MHz (ZL7201RU / ZL7261RU)

908.40 MHz (ZL7201CL/US / ZL7261CL/US)

919.70 MHz (ZL7201KR / ZL7261KR)

922-926MHz (ZL7201JP / ZL7261JP)

Operating Temp. -15°C~ 60°C (-5°F~ 140°F)

Operating Voltage: AC 100V~230V

Operating Range: Up to 100 feet (about 30m)

Data Rate: Up to 9.6k/40k/100kbps

Application: Indoor use

Max Loading

Type B: 110V/15A/1600W (Resistive)

220V15A/3200W (Resistive)

Type E, F & L: 230V/10A/2300W (Resistive)

1pc Power Monitor or On/Off Module

1pc User Manual

Z-Wave™ Command Class:

COMMAND_CLASS_APPLICATION_STATUS

COMMAND_CLASS_ASSOCIATION_GRP_INFO

COMMAND_CLASS_ASSOCIATION_V2

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_DEVICE_RESET_LOCALLY

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

COMMAND_CLASS_METER_V4 (ZL7261 only)

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_PROTECTION (ZL7201 only)

COMMAND_CLASS_SECURITY

COMMAND_CLASS_SWITCH_ALL

COMMAND_CLASS_SWITCH_BINARY mapping COMMAND-CLASS_BASIC

COMMAND_CLASS_VERSION_V2

COMMAND_CLASS_ZWAVEPLUS_INFO

Operation

If you are installing the entire Z-Wave TM system for the first time, please refer to the

installation guide of Z-Wave TM Interface Controller before installing ZL7261 or ZL7201.

1. For “Inclusion” in (adding to) a network: Put the Z-Wave TM Interface Controller into

“inclusion” mode, and following its instruction to add the ZL7261 or ZL7201 into your

controller. To get in the “Inclusion” mode, by power up to get included for first time, or

press the Program switch 3 times within 2 seconds to be included.

For “Exclusion” from (removing from) a network: Set up the Z-Wave TM Interface

Controller into “exclusion” mode, and following its instruction to delete the ZL7261 or

ZL7201 from your controller. Press the Program Switch 3 times within 2 seconds to

be excluded.

For “Association”: the Z-Wave TM interface controller set “Association”, and following its

instruction to associate the ZL7261 or ZL7201 with other device. Support one group (5

nodes). ZL7261 or ZL7201 will report back every time ON and OFF status, also it will

reports every notification to all devices in the association group.

-2-

-1-

**For making better effect, please press the button as the direction of following diagram.

2. For “Meter Supported Get” (ZL7261 only): the Z-Wave TM Interface Controller or Gateway

can send “Meter Get” command with any of the following supported scales, and the

ZL7261 will report back with the energy consumption values for the requested scale:

Scale: 0x00-kWh(Default);

0x01-kVAh

0x02-W

0X04-V

0X05-A

0X06-Power Factor.

3. LED visual indication:

Excluded Red and Green LED flashing separately

Included Switch ON Red, Switch Off Green ZL7201 only

Energy

0 ~ 5 AMP Green ZL7261 Type

B plug only

5 ~ 10 AMP Orange

10 ~ 15 AMP Red

0 ~ 3 AMP Green ZL7261 all

other plug

only

3 ~ 7 AMP Orange

7 ~ 10 AMP Red

4. Manually turn the connected appliance On/Off by your controller or pressing the Program

Switch. This is toggle switch. If the connected appliance is OFF, pressing the

Program Switch turns the connected appliance ON and vice versa.

5. The on/off function uses the Z-Wave Switch Binary Command Class (or Basic Command

Class) to control its operation. Sending a switch binary set command with a level of 0

(0x00) will turn off the device, and sending a level of 255 (0xFF) will turn on the device.

6. Repeater Function: This device acts as a repeater for the Z-Wave mesh network

functionality.

7. Support AES Function Support AES Function. Security enabled Z-Wave controller must

be used to fully utilize the product.

8. Support Meter Auto Report Function (ZL7261 only)

9. Configuration (ZL7261 only):

Parameter

Size

Value Notes

Auto report

timing 1 1 byte

60~255 seconds

(Default 60 seconds) Report kWh/kVAh

Report when

Watt change 2 2 byte

5-3600 watt for Type B

plug

5~2300 watt for all

other plug

(Default 50 watt)

Report V.A.W

10. Protection function (ZL7201 only)

Protection State Program Switch Notes

0x00 1 times (Default)

0x01 4 times Within 2 seconds

0x02 Off

11. Reset: Press the Program Switch then power on (plug-in) and hold for 5 seconds before

release the switch. Only use this procedure when the primary controller is lost or

otherwise inoperable.

12. Support OTA (Over-the Air) Firmware update from controller. Please refer to your

controller manual. Once OTA function success, please make sure to exclude the device

& include again before using the device.

13. Overload Protection: If load is excess 15.5A for Type B plug or 10.5A for all others, then

relay will automatically cut off. To restore the relay, please power off & power on the

device again.

-3-

-4-

Dieses Handbuch passt für folgende Modelle

Andere Vision Monitor Handbücher

Vision

Vision V700-T20BJ Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung