Vitality 4 Life BCWA400 Kurzanleitung
USER MANUAL
AND RECIPE BOOK
Atlas Pro
Whole Slow
Juicer
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
Atlas Pro
Whole Slow
Juicer
USER MANUAL AND
RECIPE BOOK
PG
SAFETY PRECAUTIONS AND INSTRUCTIONS 4
PARTS AND ACCESSORIES 5
ASSEMBLY INSTRUCTIONS 6
OPERATING INSTRUCTIONS 7
TROUBLESHOOTING 9
FAQs 11
CLEANING 14
RECIPES 15
WARRANTY 19
Contents
The information in this manual is intended to help you to get the
best results from your BioChef Atlas Pro Whole Slow Juicer.
Please read and follow these instructions and safeguards prior
to use.
Please keep your manual handy for future reference, warranty
information and support details.
4
SAFETY PRECAUTIONS AND INSTRUCTIONS
1. Read all instructions.
2. To protect against risk of electrical shock, do not put the
body (motor) in water or any other liquid .
3. Close supervision is necessary when any appliance is
used by children.
4. Unplug from electrical outlet when not in use and before
disassembly for cleaning.
5. Avoid contact with moving parts.
6. Do not operate appliance with a damaged cord or plug.
7. The use of attachments not recommended or sold by the
manufacturer may cause damage and will void warranty.
8. Do not let cord hang over edge of counter.
9. Make sure the motor has stopped completely before
dissembling.
10. Do not put your fingers or other objects into the juicer
while it is in operation. If food becomes lodged in the
opening, use the provided food plunger to push it down
or press the button into reverse mode. If ingredients are
still lodged in the juicing drum, turn off and disassemble
to remove remaining food. You may need to cut produce
smaller, or feed ingredients slower into the chute to
prevent this.
5
Parts and Accessories
l
1Hopper and
Feeding Chute
l
2Auger
l
3Extra Fine, Coarse
& Sorbet Strainer
l
4Spinning Brush
l
5Bowl (Drum)
l
6Motor Base
l
7Pulp Container
l
8Silicon Cover
l
9Juice Container
l
10 Cleaning Brush
l
11 Fine Cleaning Brush
l
12 Tamper
l
13 Juice Outlet Cap
l
2
l
3
l
4
l
6
l
5
l
1
l
7
l
9
l
12
l
13
l
11
l
10
l
8
6
Step 1
Firstly, ensure the yellow pulp
plug at the base of the bowl
has been inserted properly
into the outlet.
Step 2
Place the bowl firmly onto
the base.
Step 3
Place the desired strainer
into the spinning basket
and then place these into
the bowl, aligning the
assembly guide dot on
the strainer with the
triangle on the bowl.
Step 4
Insert auger into strainer/
spinning basket. Wind
clockwise until it is sitting
firmly in the bowl.
Step 5
Align the open yellow
triangles on the hopper
and twist the hopper
clockwise until the
lock position.
Assembly Instructions
1
2
3
4
5
7
Operation Instructions
Press the power switch into the ON position. Ensure that the safety switch
is unlocked and tap the door to open. Then push your larger round ingredients
into the chute allowing it to fall towards the auger. Insert other ingredients
into the smaller feeding chute individually. For best results add ingredients
at an even, slow pace to ensure maximum extraction is achieved.
Choose your Strainer
Extra Fine Strainer
This strainer is half blank, and half has small holes
to create a smoother juice with less pulp
Coarse Strainer
This strainer has larger holes to create a
whole-fruit juice (more pulp/fibre included)
Sorbet Strainer
This strainer is blank with no holes to give
you the option of making sorbets, nut butters
and more.
8
Reverse Function
If you notice any ingredients have become stuck or are refusing to move use
the tamper to gently push ingredients downwards. The Reverse Switch is
specifically for this reason. Press the Reverse Switch down for 3-5 seconds
and repeat 2-3 times if necessary.
Once the auger has come to a complete stop press the Forward switch
to continue.
Juice Outlet Cap
Close the juice outlet cap to mix your juice inside your juicer. Open the juice
outlet cap to dispense as required into the juice container.
Caring for the Silicon Pulp Plug
It is important to ensure that the Pulp Plug is always closed before juicing.
When you are cleaning the juicing drum (bowl) gently unplug the seal and
rinse under water.
Replace the seal after cleaning so your juicer is ready to use next time.
Silicon Cover
Ensure the Silicon Cover is fitted prior to use. It is another measure to ensure
that the motor is sealed from any juice overspill.
Clean after use by removing it from the motor base. Keep your spare Silicon
Covers handy in case of misplacement.
9
Troubleshooting
My juicer does not
operate when the
switch is in the
ON position
1. Make sure the power cord is properly secured into the
power source and that the switch is turned to the ‘ON’
position.
2. Check that the Hopper is assembled correctly.
PLEASE NOTE: If the Hopper has not been securely
locked in place with the arrows aligning, the appliance
will not work for safety reasons. This is due to a magnetic
safety strip located inside the hopper which must align
with the matching magnetic strip inside the base.
3. Check the appliance has been assembled according to
the instructions in this manual.
My juicer has
stopped during
operation
1. Reverse / REV to unwind any fibre that is caught
around the Auger.
2. If your juicer has stopped during operation, please
check that the hopper is correctly aligned with the
base. If the alignment shifts during operation the juicer
will stop.
3. Turn your juicer off, reset the hopper and you should
be able to continue.
PLEASE NOTE: The BioChef Atlas Pro Whole Slow Juicer
has an automatic motor cut off safety feature that
will activate if the juicer is overloaded. This has been
designed to help prevent accidental damage and to
help extend the life of the machine.
4. To reset your juicer take off the Hopper lid and remove
any ingredients in the juice bowl.
10
The Hopper will
not open
The Hopper opens in an anti-clockwise way. If the
Hopper will not open easily, try the following:
1. Allow your BioChef Atlas Pro Whole Slow Juicer to run
without adding more ingredients before turning off
and attempting to remove the Hopper.
2. Switch your juicer into reverse for a few moments to
help dislodge any remaining ingredients around the
auger and feeding chute of the Hopper.
PLEASE NOTE: The auger turns in a clockwise direction
which is opposite of the Hopper. This may cause an
unintentional tightening of the Hopper and result in
difficulty releasing the hopper from the juicing bowl.
3. After you have fed the last ingredients into the Hopper,
let it run until all the juice and pulp has run through
the machine. Pour one or two glasses of water down
the Hopper to flush out much of the left over pulp.
4. Lift off the entire juicing section before trying to
separate.
The bowl shakes
when squeezing
A slight shaking of the motor while in operation is
completely normal. Variations beyond this depend
on the fibre content of the ingredients. Hard or tough
ingredients such as carrot and beetroots may cause the
bowl to shake more than soft and juicy ingredients.
My juice is a little
pulpy, how can I
fix this?
1. Make sure the yellow silicon plug is fully inserted into
its slot. This part is removable to assist with cleaning
but is often not reinserted correctly. It acts as a pressure
point to ensure that the pulp is ejected from the pulp
tube.
2. The outlet can sometimes get blocked if ingredients
are fed too quickly into the juicer. Please try slowing
down the rate at which you insert produce into the
juicer.
3. Try cutting ingredients into smaller pieces (3 to 5cm) so
the vertical auger will be able to fully crush and process
before the next ingredient is fed in.
4. Fresh and refrigerated ingredients will have firmer
fibres and greater water content and will be less pulpy
in constitution.
5. Over time, the silicon Spinning Brush blades may
become blunt. Please contact the Customer Care
Centre or website for ordering replacement parts.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Vitality 4 Life Entsafter Handbücher
