Vitamix 120 VAC Models Bedienungsanleitung

All Models

Touch & Go®

Blending Station®

High Performance Commercial Blender

Owner’s Manual

Read And Save These Instructions

F O O D S E R V I C E

1. Read all instructions.

2. To protect against risk of electrical shock, do not put motor base in

water or other liquid.

3. Close adult supervision is necessary when appliance is used by or

near children.

4. Unplug the power cord from the wall outlet when the Touch & Go®

Blending Station®is not in use, before putting on or taking off parts,

and before cleaning other than washing the container.

5. Never contact moving parts.

6. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions or is dropped or damaged in any manner. Call

Vita-Mix®Service, (800) 4DRINK4, (800-437-4654) or 440-235-0214

at once for possible replacement, examination, repair, electrical or

mechanical adjustment. If you live outside the United States or Canada,

contact your local Vita-Mix Distributor, or phone the Vita-Mix International

Division at +1 (440) 782-2450 or email at international@vitamix.com for

a distributor in your country.

7. The use of attachments not recommended or sold by Vita-Mix

Corporation may cause fire, shock, or injury.

8. Do not use outdoors.

9. Do not let the power cord hang over edge of table or counter, or touch

hot surfaces.

10. Keep hands and utensils out of the container while motor is running

to prevent the possibility of severe personal injury and/or damage

to the Touch & Go Blending Station. A rubber scraper may be used, but

only when the Touch & Go Blending Station is not running.

11. CAUTION: Blade is sharp. Handle carefully.

• Never try to remove blade while container is sitting on the motor base.

• Do not operate with loose, knicked or damaged blades.

• To reduce the risk of personal injury, never place blade assembly on

motor base without blender container properly attached.

12. The maximum normal load is equivalent to the ounces (liters) listed

on the container, i.e., 64 oz. (2.0 liter), 48 oz. (1.4 liter), and substantially

less with thick mixtures.

13. Always operate with the lid in place.

IMPORTANT SAFEGUARDS

14. WARNING: When processing hot liquids:

• The 2-part latching lid must be securely in place. This allows steam

to escape naturally, and will prevent the lid from coming off when

the machine is turned on.

• Use caution with hot liquids. Spraying from under the lid plug can

occur, or escaping steam may cause scalding.

• Do not process hot liquids with the non-latching lid.

15. Display window area will scratch when contacted with a scouring pad or

sharp object. Use a soft cloth to wipe the control panel area clean.

16. The Touch & Go®Blending Station®cannot be cleaned with a water jet.

17. Installation for a 120 VAC unit requires you to have at least one 20 amp

outlet per machine, available within six feet of the Touch & Go Blending

Station. 220 VAC and 100 VAC units require a dedicated line. Consult

an electrician for proper electrical needs.

njoy the safety of this grounded appliance. The Touch & Go Blending

Station U.S. power cord comes equipped with a three-prong (grounding)

plug which mates with a standard three-prong wall outlet (Figure A). This

cord will vary for countries outside the United States.

Adapters (Figure B) are available for two-prong outlets. Do not cut or

remove the third (ground) prong from the plug or power cord.

Consult your electrician if you are not sure if the wall outlet is grounded

through the building wiring. With a properly grounded two prong wall outlet,

ground the machine by attaching the tab on the adapter to the wall outlet

cover by means of the screw in the center of the cover (Figure B).

SAVE THESE INSTRUCTIONS

Figure A Figure B

THREE PRONG

ADAPTERS

ARE NOT TO

BE USED IN

CANADA.

Touch & Go®Blending Station®

ON/OFF switch - Located on the side of the Motor Base the ON/OFF switch controls the

power to the machine. With the machine plugged in, switch the machine to ON to ready the

machine for blending.

START/STOP button - Pressing START/STOP once starts and runs the machine and turns

the blades. Press the START/STOP button again to stop the machine and the blades.

(NOTE: Pressing one of the PR -S T PROGRAM buttons, while the motor is running,

will also stop the machine.)

SPEED CONTRO button - Press the ▲button to gradually increase the speed of the

blades in increments of 1%, up to 100%. Press the ▼button to gradually decrease the

speed of the blades in increments of 1%, down to 7%. SP D CONTROL is used to set the

blending speed of the PULS buttons (See Instructions, pg.15) and the START/STOP button

(See Instructions, pg. 16). NOTE: These settings will reset if the power is shut off.

PRE-SET PROGRAM* buttons - These buttons, numbered 1 thru 6, are pre-programmed

blending cycles designed for the most commonly made drinks. Depending on the viscosity of

the drink you are creating, pressing one of the six PR -S T PROGRAM buttons will run the

machine for a full cycle. The machine will stop by itself when the cycle is complete. A cycle

varies in speed and length, see the Instructions on page 14 for a complete description of the

range of each PR -S T button. Due to the difference of recipes, your results may vary. See

page 6 for information on Custom Programming these six buttons.

DISP AY WINDOW-This area depending on what button is pressed,

displays a variety of operation messages. A ‘Ready’ message appears

when there is power to the machine.

Start/Stop Speed Control

Six Factory Pre-Set

Programs

Owner Controls High/Low Pulse

Display Window

ontrol Panel

READY

*Your machines PRE-SET PROGRAM buttons function and times may be different then described in the

owners manual due to your machine being custom programmed.

OWNER CONTRO S-A control panel accessible by pressing the Vita-Mix logo.

•Press once to reveal the mode message. Press button 1 then 6

within five seconds to continue. Once the correct code is entered the

display will indicate the motor temperature (Norm, Warm, Hot), a

usage count and a total. The ‘count’ is a machine usage total and

can be reset. This can be used to keep a count of the number of

drinks sold in a week, day or even an hour. To clear, press and hold

the START/STOP button for 5 seconds. The ‘total’ keeps track of

the machine usage, including production and testing, and cannot

be cleared.

•Press twice to reveal the name of the program controlling the

PR -S T buttons. If you are using the factory settings this will read

VITA-MIX BASIC PROGRAM.

• Press a third time to reveal an option to reset the PR -S T buttons

to the original factory settings.

•Press a fourth time to exit and continue blending.

HIGH/ OW PU SE button - The pulse provides a quick increase or decrease in speed

of the blades when blending. Press H to increase the motor to speeds that range from

51%-100%. Press L to decrease the motor speed down to a range of 50% -7%. The PULS

button will override the running program (as long as it is depressed). Once released the

original program continues its cycle.

• The PULS high(H) and low(L) speed is set by using the SP D CONTROL buttons.

To set, while pressing and holding a PULS button, press the SP D CONTROL ▲

or ▼button until the desired motor speed is reached. The PULS speed will remain

at this setting until changed again with the SP D CONTROL buttons.

MODE

TEMP COUNT TOTAL

NORM 25 100

VITA-MIX BASIC

PROGRAM

4 TO OVERWRITE

CURRENT PROGRAM

The Touch & Go®Blending Station®advanced electronic control can be custom programmed,*

requiring an optional programming chip, available from Vita-Mix for a nominal fee and with a

minimum unit purchase. Contact your Vita-Mix representative for more information.

Programming your On-Counter Touch & Go

Blending Station PRE-SET buttons

1. Turn the machine on.

2. Facing the front of the machine, insert the custom pro-

grammed chip with the words, “THIS SID FACING TO TH

FRONT OF TH MACHIN ” toward you and the silver contact

bars up, into the port located below the label area on the front

of the Touch & Go Blending Station. The DISPLAY WINDOW

will read ‘New Module’.

3. Within 10 seconds the SIX PR -S T buttons will be re-

programmed and the DISPLAY WINDOW will read ‘Saved’

then ‘Ready’. If nothing happens when the programming chip

is fully inserted, turn the chip in the opposite direction and

try again.

4. Remove the programming chip and return it to the original package.

5. Press one of the six PR -S T buttons to reveal, in the DISPLAY WINDOW, the name of

the program/drink.*

NOTE: If for any reason the programmed times are incorrect, they can be reset to the origi-

nal factory settings following the instructions on page 7.

Programming your In Counter Touch & Go

Blending Station PRE-SET buttons

1. Remove the container from the machine.

2. Turn the machine on.

3. Lift the machine from the bottom edges to reveal the motor and housing area. With the

machine facing towards you, locate the slot underneath on the right hand side of the

machine between the motor and the outer wall.

4. Insert the custom programmed chip into the slot with the words, “THIS SID FACING TO

TH FRONT OF TH MACHIN ” turned facing out to the right of the machine. Once inserted

the DISPLAY WINDOW will read ‘N W MODUL ’.

ustom Programming

Custom

Programmed

Chip

5. Within 10 seconds the SIX PR -S T

buttons will be re-programmed and the DISPLAY

WINDOW will read ‘Saved’ then ‘Ready’. If nothing

happens when the programming chip is fully inserted,

turn the chip in the opposite direction and try again.

6. Remove the programming chip and return

it to the original package.

7. Press one of the six PR -S T buttons to reveal, in the

DISPLAY WINDOW, the name of the program/drink.*

8. Carefully place the Blending Station motor back into

the hole in the counter.

NOTE: If for any reason the programmed times are

incorrect, they can be reset to the original factory

settings following the instructions below.

Resetting the PRE-SET buttons to the original

factory settings

WARNING: Please read all steps before reprogramming. Reverting your

PR -S T PROGRAM buttons to the original factory setting, will erase any

programming installed with a custom program chip.

1. nter the OWN R CONTROLS (press the Vita-Mix Logo) ‘Mode’ will appear in the

display window. Press the PR -S T buttons 1 and 6 then the display window will say

‘Count Temp Total’.

2. Press the Vita-Mix Logo two more times to reveal the instructions on resetting the

PR -S T buttons.

3. Press and hold the #4 button until the DISPLAY WINDOW reads ‘Restoring Please Wait’.

The PR -S T buttons are now reset to the original factory settings.

Custom

Programmed

Chip

In-Counter

Hole

*Your machines PRE-SET PROGRAM buttons function and times may be different then described in the

owners manual due to your machine being custom programmed.

Two-part Lid

48 oz. (1.4 liter) polycarbonate container

The two part lid is easy to clean and easy to put on,

take off & seal.

• To remove fully latched lid, squeeze tabs together on

both sides of the container, pull upward and off.

• Twist the center lid plug to fasten or remove.

NOTE: To make new lids easier to insert and remove, rub a

light coating of cooking oil around bottom where it seals. Place it in

container for several minutes, remove and lightly wipe oil off lid.

Two-part Lid

64 oz. (2.0 liter) polycarbonate container

The two part lid is easy to clean and easy to put on

and take off.

(Note: Brand new lids are a little stiff. This is

temporary.)

• The lid has a continuous rim which latches

inside the container tabs. Push one side

of the rim under one tab, and with the heel

of your hands push down, over the opposite

tab, to snap lid into position.

• To remove lid, place hands around the lid,

pressing thumbs above one of the container

tabs. Push in and lift off.

• Twist the center lid plug to fasten or

remove.

One Piece Lid (optional)

64 oz. (2.0 liter) polycarbonate container (Figure C)

48 oz. (1.4 liter) polycarbonate container (Figure D)

The one piece lid is easy to clean and easy to put on

and take off.

(Note: Brand new lids are a little stiff. This is temporary.)

• Follow the instructions above for placing the lid on the

container and removing it from the container.

• 48 oz. / 1.4 liter lid does not latch.

• Add ingredients through port on top.

CAUTION: Do not use non-latching lid when processing

hot ingredients.

CUPS

Figure A

Figure C

Figure D

Figure B

To secure lid plug, rotate it

so one tab locks between the

stops on top of rubber lid.

Always latch lid when

processing hot liquids.

Press in

above

container

tab to

remove

lid

Rim

Container

Tab

id Assembly

Tamper

Cover with Removable Hinge Design

Cover Door:

1. The Cover Door can be removed by opening it until the door is horizontal. Then,

gently spread the sides of the door over the round hinges and remove.

2. To reinstall the Cover Door, gently spread the sides of the door and place the door

hinge cutouts over the round hinges. (Figure )

Back Cover:

1. To remove the Back Cover from the Blending Station:

a. First remove the Cover Door from the unit, as described above.

b. Remove the two (2) Back Cover mounting screws located on the rear of the

machine. (Figure F)

c. From the rear of the machine, firmly push the bottom of the cover forward

(towards the control panel), keeping the bottom edge of the cover against the

motor base. DO NOT tilt or strike the cover during removal.

d. Slide forward until the side latches on the front of the cover are released from the

motor base. DO NOT strike the cover to “pop” the side latches from their

tracks. Doing so will cause damage. The cover must only be removed by

sliding it forward (towards the Control Panel).

2. To replace the Back Cover on to the Blending Station:

a. Place the Back Cover on the motor base approximately one (1) inch (2.54 cm)

forward of its normal position.

b. Slide the cover towards the back of the machine (away from the Control Panel).

Make sure the side latches slide into their tracks.

c. Push until back of cover is seated against the Motor Base.

Make sure the Back Cover is fully seated in the back and the side latches

are in their grooves before inserting and tightening the mounting screws.

d. Replace and firmly tighten the two (2) Back Cover mounting screws. (Figure F)

DO NOT overtighten. DO NOT use the mounting screws to pull the Back

Cover into position. Doing so will cause damage.

Figure Figure F

Back Cover

Mounting

Screws

Cover Door

Hinge

Preparing the counter area:

• Before cutting holes, make sure that there is adequate clearance under the counter for the

motor. The motor will extend about 5-2/3" (14.4 cm) below the counter but it is best to allow

at least 10" (25.5 cm) from the under-counter to shelves or any other equipment under the

counter. Also, when using the removable cover design, the back of the hole must be at least

6” (15.2 cm) from any wall to allow for cover door clearance.

• An extra 6.5” (16.5 cm) of open space, above the top of the cover will be needed for

placement and removal of the In-Counter machine and for custom programming the SIX

PR -S T Buttons.

• If installing unit into a closed cabinet, use a 4” dia. (10.1 cm) flexible vinyl duct (dryer hose)

to vent exhaust. Attach the vinyl duct to the bottom of your In-Counter Touch & Go®

Blending Station®by forcing the end of the hose over the exhaust baffle of the unit. Run the

vinyl duct out of the cabinet for proper ventilation. Do not vent hose into a wall, ceiling, or a

concealed space of a building. Multiple units should not vent to a common manifold unit but

to separate places. If running your Blending Station causes a suction on your cabinet door,

place a spacer in the door frame to allow proper intake of air.

Do not use hose clamps or equivalent to attach exhaust hose on machine.

• When cutting holes for placement of multiple In-Counter units, position the edge of the

machines at least 12” (30.48 cm) apart to ensure quick cleaning and proper venting

between machines.

• In-Counter installation for a 120 VAC unit also requires you to have at least one 20 amp

outlet per machine under the counter, available within six feet of the Touch & Go Blending

Station. 220 VAC and 100 VAC units require a dedicated line. Consult an electrician for

proper electrical needs.

• The In-Counter Blending Station also requires a gasket (provided in the machine’s original

package) to be placed between the machine and the counter. See page 12 for instructions.

DO NOT strike the blender when removing from the counter.

Electrical requirements:

• 120 VAC • 50/60 Hz. • 11.5 amps

• All Touch & Go Blending Stations are built using a U.S. 3 prong

grounded cord and require a 20 amp outlet.

• 220/240 VAC • 50/60 Hz. • 1073-1176 Watts

• 100 VAC • 50/60 Hz. • 900 Watts

n-Counter Installation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vitamix Mixer Handbücher

Vitamix

Vitamix Drink Machine Advance Bedienungsanleitung

Vitamix

Vitamix Creations II Bedienungsanleitung

Vitamix

Vitamix Barboss Advance Bedienungsanleitung

Vitamix

Vitamix 6500 Bedienungsanleitung

Vitamix

Vitamix Blending Station MP Bedienungsanleitung

Vitamix

Vitamix Venturist Series Bedienungsanleitung

Vitamix

Vitamix Professional Series 750 Bedienungsanleitung

Vitamix

Vitamix 7500 Bedienungsanleitung

Vitamix

Vitamix VM0185A Bedienungsanleitung

Vitamix

Vitamix One Bedienungsanleitung

Vitamix

Vitamix PROFESSIONAL SERIES 500 Bedienungsanleitung

Vitamix

Vitamix Ascent SERIES Bedienungsanleitung

Vitamix

Vitamix Touch & Go Advance VM0199 Bedienungsanleitung

Vitamix

Vitamix The Quiet One Bedienungsanleitung

Vitamix

Vitamix Ascent A2500i Bedienungsanleitung

Vitamix

Vitamix BarBoss Advance Bedienungsanleitung

Vitamix

Vitamix Bar Boss Bedienungsanleitung

Vitamix

Vitamix BarBoss Advance Bedienungsanleitung

Vitamix

Vitamix VM0104 Bedienungsanleitung

Vitamix

Vitamix Ascent SERIES Bedienungsanleitung

Vitamix

Vitamix Quiet One VM0145 Bedienungsanleitung

Vitamix

Vitamix A2300 Bedienungsanleitung

Vitamix

Vitamix Professional Series Bedienungsanleitung

Vitamix

Vitamix Ascent SERIES Bedienungsanleitung

Beliebte Mixer Handbücher anderer Marken

ROTOR

ROTOR 1125.201 Bedienungsanleitung

Braun

Braun Multiquick 5 Vario series Bedienungsanleitung

ARENDO

ARENDO MIRA 305424 Bedienungsanleitung

CHEF-BUILT

CHEF-BUILT CCB-3500 Bedienungsanleitung

Viconte

Viconte VC-4406 Bedienungsanleitung

Oster

Oster BLSTAB-CB0 Bedienungsanleitung

HOFFEN

HOFFEN MC-3005 Bedienungsanleitung

Black & Decker

Black & Decker BLC18750DM Bedienungsanleitung

Sunbeam

Sunbeam 4182 Bedienungsanleitung

Bialetti

Bialetti FMX35 Bedienungsanleitung

Black & Decker

Black & Decker BL8000 Bedienungsanleitung

Duronic

Duronic BL530 Bedienungsanleitung

Exquisit

Exquisit MS 3002 wes Bedienungsanleitung

Lumme

Lumme LU-KP1891A Bedienungsanleitung

Binatone

Binatone HB-735 Bedienungsanleitung

Moulinex

Moulinex LM936E10 Bedienungsanleitung

Oster

Oster VERSA Installations- und Betriebshandbuch

Ninja

Ninja NN210Q Bedienungsanleitung