Vitek VTC-C2BTS2 Bedienungsanleitung
FEATURES:
• 1/2.8” Sony® Exmor Progressive Scan CMOS Sensor
• 2.1 MegaPixel with Full 1080p/720p TVI Output
• Sensitivity of 0.0009 Lux
• Smart Motion Zoom tracks motion, then intelligently zooms into that area of
the frame
• 3D-DNR Digital Noise Reduction
• CVBS (Analog) Output by BNC
• True Day/Night by ICR - Dual Filter Switch
• Fully programmable True WDR (Dual Scan)
• Advanced OSD Functions: NORMAL, WDR, D-WDR, 3DNR, Motion Detection,
Privacy Mask, D-Zoom(~8x), Sens-up(x32), Flickerless, BLC/HLC, Defog,
Pixel Defect Compensation, Title Set, LSC, Deblur, Flip
• External control via RS-485
• Low active TTL input from External IR illuminators
• 12VDC / 24VAC Dual Voltage Operation
VTC-C2BTS2
2.1MP Smart TVI WDR
Box Camera
VITEK
VITEK
Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Mains power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power mains interruptions, it is
recommended that the model be powered from an uninterruptible power supply
(UPS) or a battery.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
2 3
Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing areas where has shock or vibration which results in the problems.
Pay attention to safety when laying the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
Never open the device such as boards.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to destruction.
The camera should never be operated in water.
3
Contents
Safety Precaution
p.02~03
Contents
p.04
Features
p.05
Composition
p.06
Dimensions
p.06
Part Names
p.07
Installation Instructions
p.08
Operating Instructions
p.09~22
Specifications
p.23
4 5
Features
Key Features
• Full HD, 2Mega Pixel HD-TVI CAMERA, 1920x1080(30p)
• TVI Video Transmission Distance over Coax.; 500M (RG59, 75Ω)
*depending on cable condition and characteristics
• Automatically removable IR Cut filter by Dual filter switcher
• CS mount supported (Option: C-mount adaptor)
• True WDR(Wide Dynamic Range)
• Improved Noise reduction with the enhanced 3D-NR
• Pointing Zoom which enables flexible zooming of any area.
• Smart Motion Zoom in combining with Pointing Zoom.
(Automatic zoom in/out when motion is detected)
• Preset Zoom
• Motion Detection, Privacy Mask, Defog, Sens-up(x32), D-WDR,
H/V/HV Flip, D-Zoom(1.1x~8x), LSC(Lens Shade Compensation),
BLC/HLC, Pixel Defect Compensation, Title Set
• Top performance at low light sensitivity (Sens-up On)
• Video output HD-TVI or CVBS switchable
• OSD MENU & Video Sub-out port for easy installation & maintenance
• Reverse polarity protection circuit
• Isolated power supply against ground loop problem
• Back focus adjustment
• Remote control via RS-485 (Pelco-D/P)
• UTC Control through HD-TVI DVR.
• AC24/DC12V Dual power
General Description
• ICR mechanism:
- Enhances its sensitivity about 10x at night time
- Can accept infrared light
• Intelligent Focus Indicator and FOCUS ASSIST menu:
- Offers easy adjustment of Focus
• 24VAC/12VDC dual power design:
- Offers flexibility of installation
- Ensures the reliability
This camera realizes the natural and crisp image as you see the scene
in front of you by Full HD(1920x1080p) camera module.
5
Dimensions
Composition
Torque Wrench:
3mm (1pc)
Dust Protection
Cap (1pc)
Operating
Instruction
Standard Box Camera
2.83”
2.99” 2.99”
Ø1.38”
3.5”
6 7
Part Names
• Care should be taken that the cable is NOT damaged, kinked or exposed in
a hazardous area.
• Do not point the camera lens directly at the sun or a spot light.
[ CAUTION ]
④
① OSD Control Joy stick
② Power input terminal
(AC24V/DC12V or DC12V)
③RS-485 / IR connector
④
HD-TVI
output connector
⑤ Power LED
⑥ VIDEO output connector
③
①
⑤
⑥
②
Torque
Wrench
Dust
Protection Cap
No.
1
2
3
4
DC Iris
Damp(-)
Damp(+)
Drive(+)
GND
Front Case
Rear Case
Back focus
adjustment
Mount Holes
(Top / Bottom)
SIDE VIEW
Lens Connector
for Auto Iris lenses
PIN 1PIN 3
PIN 2PIN 4
REAR VIEW
7
Installation Instructions
Installation Instructions
• Care should be taken that the cable is NOT damaged, kinked or exposed in
a hazardous area.
• Do not point the camera lens directly at the sun or a spot light.
• The camera has a 1/4” thread insert on top and bottom for mounting
the camera to a wall or ceiling with a corresponding mount.
Power Supply Connection
Camera can work with either 24VAC or 12VDC, dual voltage power.
Primary and secondary grounds are completely isolated to avoid the possible
ground-loop problems.
Using OSD Controller
Setup menu can be accessed and controlled by OSD control joy stick on the rear
of the camera unit. Five commands are available with the joy stick. The design
of OSD could be different according to the Model.
Description of the joystick operation
1) SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down for about 1.5sec
2) UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3) LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu.
Used to adjust the desired menu selection and to move the cursor left or right.
4) denotes a long press down for about 2 seconds
Description of the D-ZOOM* adjustment
1) ▲: Zoom In 2) ▼ : Zoom Out
(*) Works only when OSD Menu is inactive.
Do not power off the camera immediately after switching the video format .
It can cause a crash of the flash memory.
Description of Video format switch (TVI ↔CVBS)
1) Selects the video output TVI or CVBS. Default position is TVI.
2) Switching the video format : ▲,▼, ▲,▼, ● ( long push 1~2 sec.)
8 9
Operating Instructions
OSD menu Startup
Press ‘●’(OSD menu Joy stick key) down for about 2 seconds to access the
setup menu mode.
MENU V3.xx
1. EXPOSURE
2. LENS
3. FOCUS ASSIST
4. SCENE ENHANCE
5. 3D-NR
6. DAY/NIGHT
7. PICT ADJUST
8. SPECIAL
9. SYSTEM
A. EXIT
NORMAL
MID
AUTO
SAVE&EXIT
DC
Direct Control menu
MAIN
DEFAULT
DESCRIPTION
LENS
Sets Lens types.
DC
FOCUS ASSIST
Sets Focus Adjustments.
-
EXPOSURE
Sets SHUTTER MODE, BRIGHTNESS, SENS-UP and AGC.
-
SCENE
ENHANCE
NORMAL SCENE ENHANCE provides several ways to enhance the video
in various environments with settings of NORMAL, WDR,
D-WDR, BLC and HLC.
NORMAL – Optimized for the normal indoor and outdoor in good
lighting condition.
WDR – Improves the visibility for bright areas and dark
areas by the double capture of image with LONG and SHORT
exposures. With WDR ON, the frame rate becomes half by the double
capture. WDR level can be selected from LOW, MID and HIGH.
Care should be taken to select this mode because video may lose
its quality in some environments by over compensation.
※CVBS video signal:Connecting 2nd video to CVBS port disables
WDR function temporarily. It should be considered when installer
adjusts the video with installation monitor via CVBS video signal.
• RET : Returns to the previous menu.
• EXIT : Exits the menu setting without save.
• SAVE&EXIT : Exits the menu setting with save.
9
Operating Instructions
FULL-HD MEGA-PIXEL CAMERA
D-WDR – Improves the visibility by compensating the video gain for
the dark area. Noise can increase in the dark area accordingly.
Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA, SHADING
PICT ADJUST
Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET,
DISPLAY, DEFOG, POINTING ZOOM, PRESET ZOOM
SPECIAL
SYSTEM
SAVE & EXIT – Exits the menu after saving the parameters.
EXIT – Exits the menu without saving.
EXIT
DAY/NIGHT is used to control the setting during day-time and night-time
operation. Select the mode according to the lighting conditions and the
camera type. SMART (DYNAMIC) IR can be set to reduce the saturation
by strong IR illumination at night in any menu. Setting SMART
(DYNAMIC) IR in any menu is identically applied to other menu. Zero(0)
turns off SMART (DYNAMIC) IR and High setting decreases the
saturation but the corners will be darker accordingly.
EXT – DAY or NIGHT is determined by the built-in light photo sensor.
Camera with IR LED must be set to EXT.
AUTO – Used when DAY or NIGHT is determined by light level through the
lens and DAY from/to NIGHT is switched automatically by the scene
brightness. D↔N THRESHOLD, D↔N DELY and SMART (DYNAMIC) IR
can be set in the menu. When EXPOSURE>AGC is less than 10,
DAY/NIGHT AUTO is disabled and forcibly switches to ___(DAY) to avoid
malfunction. EXT, B/W (NIGHT) and COLOR (DAY) is independent on AGC
level. When EXTERNAL IR LED is used with NON IR LED model, please
set to IR LED MODE ON.
B/W(NIGHT) – Removes IR cut filter and switches to B/W regardless of
light level.
COLOR(DAY) – DAY/NIGHT is disabled and outputs color video.
DAY/NIGHT
OFF, LOW, MID and HIGH.
EXT
for
IR LED
SCENE
ENHANCE
NORMAL
3D-NR MID
BLC – Improves the visibility for dark objects by bright back
light. Outside area of BLC window can over saturate.
BLC has a target window for compensation and its size and position
can be set by H-POS, V-POS, H-SIZE and V-SIZE.
HLC – Cuts out the bright area with a black mask and excludes it from
compensation. Lower HLC LEVEL cuts out video from lower light levels
(more sensitive).
Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE,
VIDEO OUTPUT SELECT and FACTORY DEFAULT
10 11
Inhaltsverzeichnis
Andere Vitek Camcorder Handbücher
Beliebte Camcorder Handbücher anderer Marken
Panasonic
Panasonic AG-HMC152EN Bedienungsanleitung
Insignia
Insignia NS-DCC5HB09 - Camcorder - 720p Bedienungsanleitung
MYDLINK
MYDLINK DCS-6100LH Bedienungsanleitung
Sony
Sony video Hi8 Handycam CCD-TR555 Bedienungsanleitung
SECURECOM
SECURECOM V-5014B Bedienungsanleitung
Panasonic
Panasonic HDC-SD100 Bedienungsanleitung
