Vivid Veloblade Volta Bedienungsanleitung

Introduction User

Manual for

Contents

Page 2-3: Chapter 1 –Machine set up

Page 4-5: Chapter 2 –Tools and their positions

Page 6-10 : Chapter 3 –Tool settings & Test Depth

Page 11-15: Chapter 4 –Software lay-out

Page 16: Chapter 5 –Importing files

Page 17-20: Chapter 6 –Software modes

Page 21: Chapter 7 –Blade changing

Page 22-24 : Chapter 8 –Maintenance

1.Machine set up

Power on the machine, ensure all switches are in the up position [figure 1.1]

Open the Veloblade software [figure 1.2]

If the feeder is needed please load the media onto the feed table. [figure 1.3]

Ensure the media has movement and the magnetic back stop and side lays are

not too tight. The position of the magnetic sides are important., these cannot

be past the red line shown in figure 3. The red line represents where the

movement of the feed head moves to pick up a sheet.

Figure 1.1

Figure 1. 2

Figure 1.3

Once the material is loaded into the feeder press the green button and feed

table will move into position and the lights will illuminate [Figure 1.4].

If you require a roll of material cutting, remove all media from the feed table,

load the material onto the mandrel, put in the mandrel brackets and place the

idle bar in position [Figure 1.5]. Now thread the material around the idle bar

and place onto the cutting bed [Figure 1.6].

Figure 1.4

Figure 1.5

Figure 1.6

2. Tools and their positions

The tools used on the Veloblade Volta and their positions on the machine [see

figure 2.1 below for positions]:

Position 1

•PCTT –Crease tool

Position 2

•RCT –Rotary cutting tool [for materials up to 2mm]

Position 3

•PRCT –Pen tool

•RCT –Rotary cutting tool [in this position we use the RCT for kiss cutting]

Figure 2.1

RCT/PRCT:

Remove the locking the screw and cap [Figure 2.2] and place the tool in the

holder. Ensure the tool is pushed all the way into the holder to the lip on the

tool [Figure 2.3] and reattach the locking screw and cap.

For blade changing please see chapter 7.

PCTT:

To remove the crease tool pull down on the crease wheel [figure 2.4 & 2.5], to

reinsert place the wheel into the slots and push upwards [figure 2.6].

Figure 2.2

Figure 2.3

Figure 2.4

Figure 2.5

Figure 2.6

3. Tool settings & Test depth

Switch the window to Debug View and select the tool position you want to set

[Figure 3.1].

Move the head [using the arrow keys on the keyboard] over your test material

ensuring the tool you are setting is located above the material and press T-

depth [Figure 3.2].

Turn off the Vacuum [Vac1] and move the head out of way using the arrows on

the keyboard. Inspect the test cut, Ensure it is a clean cut all the way through

the media. Too much blade will leave a rough cut and raised edges and not

enough will not cut all the way through the media.

For other [i.e. speed] adjustments click on Cutting tool configuration near the

top of the screen [Figure3.3].

Figure 3.1

Figure 3.3

Figure 3.2

Select the tool position for the tool you want to change the speed for, alter to

the desired speed [figure 3.4]. For creasing, if the speed is to high it can cause

cracking on coated stocks.

Click save and close the window.

PRCT/RCT:

Changing the depth of the blade on these tools is done manually.

Remove the tool from its tool position, loosen the brass locking nut [Figure 3.8]

and turn the top knurled knob for more or less blade [Figure3.9].

Figure 3.4

Figure 3.8

Figure 3.9

Too much blade showing and it will leave a rough cut. To get the correct

amount of blade for a through cut hold the material you wish to cut at the end

of tool holder near the blade [Figure 3.10] and adjust the blade to the required

depth.

For Kiss cutting on materials [i.e. crackback, vinyl] the blade depth needs to be

minimal, see the difference between figure 3.11 [Set for through cut] and

figure 3.12 [set for kiss cutting].

Manually test the tool to check if the blade is at the correct height, hold the

tool firmly and straight, While applying a substantial amount of pressure draw

Figure 3.10

Figure 3.11

Figure 3.12

Figure 3.13

a circle on test material [this must be done on the belt of the machine] see

figure 3.13.

Once the blade is set and manually tested, return the tool to its position on the

machine and secure. The next step is to do a test cut, place a piece of scrap

material onto the belt, move the head into position over the media and press

T-depth in the Debug View window.

If you’re getting marking from the tool holder on the media [Figure 3.14] or the

tool is not making contact with the media, You will need to change the

pressure of the tool solenoid, Click on Cutting Tool Configuration, select the

number of the tool you are using [3 or 4], change the maximum knife lowering

depth.

Decreasing the number will apply less pressure.

PCTT:

There are two ways to adjust the amount of pressure on the crease wheel, the

first is to adjust the valve and allow more or less air pressure [Figure 3.16].

Anticlockwise will reduce the amount of air pressure.

Figure 3.14

Figure 3.15

Figure 3.16

Inhaltsverzeichnis

Andere Vivid Cutter Handbücher

Vivid

Vivid Flatbook Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung