Vivitar Vivicam 35 Bedienungsanleitung
Vivicam 35 User Manual
English 040208tp
Contents
1. Introduction 1
1.1. Overview 1
1.2. Warnings and Precautions 1
1.3. Package Contents 4
1.4. System Requirements 4
1.5. Vivicam 35 Features 5
2. Installing the Batteries 6
3. Installing the Software 8
3.1. Twain Driver for Windows-based PCs 8
3.2. ArcSoft Suite 9
3.2.1. PhotoImpression 9
3.2.2. VideoImpression 9
3.3. NetGUI In-A-Flash Photo 9
3.4. User Manual 10
4. Capturing Images 11
4.1. Power On the Camera 11
4.2. Capture an Image 12
4.3. Camera Status Icons 13
4.4. Power-Off the Camera 14
4.5. Flash Charging 14
4.6 Self-Timer 15
4.7 AVICapture 15
4.8 Continuous Capture 16
4.9 Deleting Images 16
4.10 Image Resolution 17
4.11 High/Low Image Compression 18
4.12 Lighting Frequency 18
4.13 Using the Flash –Automatic, or On/fill 19
4.14 Techniques for Capturing the Best Images 19
5. Downloading Images to Your PC 20
5.1. Transfer Images to your PC 20
5.2 Transferring Images to the application software 22
6. PC/Web Camera Video Function 23
6.1. Using the ViviCam 35 in Video Mode 23
6.2. UsingtheViviCam35withPCCam 24
6.3. Using the ViviCam 35 with NetMeeting 24
6.4. Using the ViviCam 35 with Movie Maker (Windows XP) 25
7. Specifications 26
1.0 Introduction -
1.1 Overview -
Thank you for purchasing the Vivicam 35 digital camera. It can capture
digital images, short video-clips (continuous shooting mode), and it can also
serve as a PC/Web camera. The V35 is equipped with 8 MB of memory to
store your images and movie clips. You may download your images and
movie clips to your computer using the USB cable and included software.
1.2 Warnings and Precautions -
1.2.1 FCC STATEMENT -
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
Class B digital devices, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
-1-
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna
2. Increase the separation between the equipment and receiver
3. Connecttheequipmentintoan outlet on a circuitdifferentfromthat
to which the receiver is connected
4. Consult the dealer or an experienced radio/TV technician for help
Use of shielded cable is required to comply with Class B limits in Subpart B of
Part 15 of the FCC rules. Do not make any changes or modifications to the
equipment unless otherwise specified in the manual. If such changes or
modifications should be made, you could be required to stop operation of the
equipment.
1.2.2 GENERALWARNINGS –
Do not use batteries other than those specified for use with the camera. The
use of unsuitable batteries may result in the batteries splitting or leaking and
causing a fire, injury, or soiling of the battery compartment.
-2-
When placing batteries in the camera, check the polarity of the batteries (- and
+) to ensure proper orientation. Incorrect polarity may result in the batteries
splitting or leaking and causing a fire, injury, or soiling of the battery
compartment.
Remove the batteries if the camera will not be used for an extended period of
time. The batteries may leak and cause a fire, injury or soiling of the battery
compartment. If the batteries leak clean and wipe the battery compartment
carefully and install new batteries. Wash your hands carefully if you touch
the battery fluid. Please note that when you remove the batteries your
images will be lost from the camera memory.
WARNING: Handling the USB cable on this product may expose you to
lead, a chemical known to the State of California to cause birth defects or
other reproductive harm. Wash your hands after handling.
1.2.3 TRADEMARK INFORMATION -
Microsoft® and Windows® are U.S. registered trademarks of Microsoft
Corporation.
Pentium® is a registered trademark of Intel Corporation. Other names and
products may be trademarks or registered trademarks of their respective
owner.
-3-
1.3 Package Contents -
The Vivicam 35 package typically includes:
1. Camera
2. USB cable
3. CD ROM with Twain Driver andApplication Software
4. User Manual
5. Three (3)AAAbatteries
6. Hand strap
Note: Included components may vary, as specified by local retailers and
locations. Check with your retailer for specifics.
1.4 System Requirements -
You must use a computer to download the images from your Vivicam 35.
The computer that you use must meet the following minimum requirements:
1. Windows Me/2000/XP
2. Direct X 8.0, or higher
3. 128 MB RAM
4. 60 MB hard disk space available
5. Available USB port
6. CD-ROM drive
-4-
1.5 Vivicam 35 Features -
Front Side:
Back Side:
-5-
2.0 Installing the Batteries -
Step 1: Open the battery door by lifting the tab on the
door.
Step 2: Insert threeAAAbatteries with the polarity as
shown:
Step 3: Close the battery cover.
Warning: Do not open the battery door when the camera is powered ON.
This will cause all images in memory to be lost immediately. If you open the
battery door when the camera is OFF (when changing the batteries) you must
close the door within thirty (30) seconds or your images will be erased from
memory.
Notes:
1. Always download your images to your computer soon after you
have captured them. Never assume your images will be retained
for more than three or four days. If the batteries are depleted,
your images will be lost.
2. If you must change the batteries, makes sure the camera is OFF
-6-
and then change the batteries in less than thirty (30) seconds.
3. If you will not use the camera for a long time (several days, or more)
remove the batteries. The batteries will discharge slowly if left in
the camera. This may cause complete battery discharge as well
as loss of images. The batteries may corrode if left in the camera
for extended periods of time.
4. Dispose of batteries properly in accordance with local laws and
regulations. Do not place them in fire.
5. The Vivicam 35 has an automatic power-saving feature. The
camera will turn off automatically if it has not been used after
approximately thirty (30) seconds.
6. When the camera is connected to a computer using a USB cable,
it is not necessary to use batteries because the camera uses the
power provided by the computer through the USB interface.
-7-
Inhaltsverzeichnis
Andere Vivitar Digitalkamera Handbücher
Vivitar
Vivitar Vivicam 3705 Bedienungsanleitung
Vivitar
Vivitar ViviCam F328 Bedienungsanleitung
Vivitar
Vivitar ViviCam S425 Bedienungsanleitung
Vivitar
Vivitar ViviCam T135 Bedienungsanleitung
Vivitar
Vivitar Vivicam 5385 Bedienungsanleitung
Vivitar
Vivitar VIVICAM T024 Bedienungsanleitung
Vivitar
Vivitar Vivicam 2000 Bedienungsanleitung
Vivitar
Vivitar Vivicam 2200 Bedienungsanleitung
Vivitar
Vivitar Vivicam 3540 Bedienungsanleitung
Vivitar
Vivitar VIVICAM X026 Bedienungsanleitung
Vivitar
Vivitar ViviCam X035 Bedienungsanleitung
Vivitar
Vivitar ViviCam 3100 Bedienungsanleitung
Vivitar
Vivitar v4000 Bedienungsanleitung
Vivitar
Vivitar VIVICAM 5386 Bedienungsanleitung
Vivitar
Vivitar Vivicam 5340s Bedienungsanleitung
Vivitar
Vivitar ViviCam i7 Bedienungsanleitung
Vivitar
Vivitar Vivicam 3500 Bedienungsanleitung
Vivitar
Vivitar ViviCam S130 Bedienungsanleitung
Vivitar
Vivitar ViviCam 5388 Bedienungsanleitung
Vivitar
Vivitar Vivicam 3780 Bedienungsanleitung
