Vivitek DU6675 Bedienungsanleitung

DU6675

Remote Communicaton

Manual

DU6675 DLP Projector Remote Communication Manual

Table of Contents

The Serial Interface RS-232 Command............................................................................................2

Communication parameter setup................................................................................................................................... 2

Operation commands..................................................................................................................................................... 2

Operation command syntax.................................................................................................................................... 2

List of operation commands.................................................................................................................................... 3

Simulated IR remote controller commands.................................................................................................................. 10

Control the Projector through a Network ......................................................................................11

Cable connection ......................................................................................................................................................... 11

Set up the projector for networking .............................................................................................................................. 12

Control the projector through a network....................................................................................................................... 13

Control the projector through a web browser ....................................................................................................... 13

Control projector with the PJLink protocol ............................................................................................................ 16

Control projector with TCP/IP communication protocol ........................................................................................ 16

About the VIVITEK support.............................................................................................................17

DU6675 DLP Projector Remote Communication Manual

The Serial Interface RS-232 Command

This controller supports projectors with a RS-232 serial terminal, there exist two types of serial commands:

Operation command: Available menu options are PICTURE, SIGNAL, SETUP, INSTALLATION, SERVICE, and

OTHERS.

Simulated IR remote controller commands: Controls projector via RS-232 command, the commands simulate IR

remote controller and its control keys.

Communication parameter setup

You can use the serial control command to input commands for projector control or retrieve its operational data through

Windows client terminal software, e.g. Hyper Terminal, with ASCII characters.You need to set up the following

communication parameters in advance:

Item Parameter:

Bit per Second 38400 (default), 19200, 9600bps

Data Bit 8-bit

Parity None

Stop Bit 1

Flow Control None

Port 7000

Operation commands

Operation command syntax

An operation command is prefixed by character "op", followed by control commands and settings separated by space

blank [SP], and ended by carriage return pair "CR" and "ASCII hex 0D".Syntax of serial control commands:

op[SP]<operation command>[SP]<Setting Value>[CR]

op :

A constant indicating this is an operation command.

[SP] :

Indicate one blank space.

[CR] :

Indicate the command ending carriage return pair "CR" and "ASCII hex 0D".

Setting value : Settings of operation command

Types of setup strings Characters of settings Description

Query current setup ? Question mark "?" indicates querying current setup

Setup = <settings> Syntax: Symbol "=" suffixed with setup values

Increase setup order of

adjustment items

+ Some settings are changed in steps. Symbol "+"

indicates changing one step up

Decrease setup order of

adjustment items

- Some settings are changed in steps. Symbol "-"

indicates changing one step down

Execute operation command None Certain operation commands execute after input

without further setting or regulators.

Examples:

Control items Input command row Projector return message

Query current brightness op bright ? [CR] OP BRIGHT = 101

Set up brightness op bright = 127 [CR] OP BRIGHT = 127

Set up input signal source to

HDMI

op input.sel = 0 [CR] OP INPUT.SEL = 0

Reset camera to center position lens.center

Note:

When sending the multiple commands, make sure the return message of the last command is received before

sending out the next one.

Note:

The terminal software does not return every command input character

The transmission performance varies with the length of RS-232 cable and transmission speed. Please

select

er baud rate from the OSD menu.

DU6675 DLP Projector Remote Communication Manual

List of operation commands

PICTURE

OSD Function Operation

command Settings/Return Values Note

Picture Mode pic.mode ?

0 = High Bright

1 = Presentation

2 = Video

Not applicable when the project is in

standby mode.

Brightness bright ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Contrast contrast ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Saturation saturat ?

0-200

a. Apply for YUV signal input

b. Not applicable when the project is

in standby mode or the input signal

is not locked yet.

Hue tint ?

0-200

a. Apply for YUV signal input

b. Not applicable when the project is

in standby mode or the input signal

is not locked yet.

Sharpness sharp ?

0-31

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Color Temperature color.temp ?

0 = Native

1 = 6500K

2 = 7800K

3 = 9300K

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Gamma gamma ?

0 = 2.2

1 = Film

2 = Graphics

3 = Video

4 = PC

5 = S Curve

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Auto Sync auto.img (execute) Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Input Balance /Red

Offset

red.offset ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Input Balance /Green

Offset

green.offset ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Input Balance /Blue

Offset

blue.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

DU6675 DLP Projector Remote Communication Manual

OSD Function Operation

command Settings/Return Values Note

Input Balance /Red

Gain

red.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Input Balance /Green

Gain

green.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Input Balance /Blue

Gain

blue.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Red Gain hsg.r.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Green Gain hsg.g.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Blue Gain Hsg.b.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Cyan Gain hsg.c.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Magenta Gain hsg.m.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Yellow Gain Hsg.y.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Red/Saturation hsg.r.sat ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Green/Saturation hsg.g.sat ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Blue/Saturation Hsg.b.sat ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Cyan/Saturation hsg.c.sat ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Magenta/Saturati

hsg.m.sat ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

DU6675 DLP Projector Remote Communication Manual

OSD Function Operation

command Settings/Return Values Note

HSG/Yellow/Saturation Hsg.y.sat ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Red/Hue hsg.r.hue ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Green/Hue hsg.g.hue ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Blue/Hue Hsg.b. hue ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Cyan/Hue hsg.c. hue ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Magenta/Hue hsg.m. hue ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/Yellow/Hue Hsg.y. hue ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/White/Red Gain hsg.wr.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/White/Green Gain hsg.wg.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

HSG/White/Blue Gain Hsg.wb.gain ?

0-200

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Noise Reduction nr ?

0-15 (Noise Reduction)

Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Dynamic Black dblack ?

0 = Off

1 = On

Not applicable when the projector is

in standby mode.

DU6675 DLP Projector Remote Communication Manual

SIGNAL

OSD Function Operation

command Settings/Return Values Note

Input Select input.sel ?

0 = HDMI

1 = DVI

2 = VGA

3 = 5BNC

4 = Component

5 = S-Video

6 = Video

7 = HDBaseT

Not applicable when the project is at

below status.

Standby mode

When the blank function is

activated

Auto Search auto.src ?

0 = Off

1 = On

Not applicable when the projector is

in standby mode.

Color Space color.space ?

0 = Auto

1 = YPbPr (Rec. 709)

2 = YcbCr (Rec. 601)

3 = RGB-PC (0-255)

4 = RGB-Video (16-235)

Not applicable when the project is in

standby mode or the input signal is

not yet locked.

VGA Setup/H Total h.total ?

0-200

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

Apply for VGA and Component

signal input.

VGA Setup/H Start h.pos ?

0-200

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

Apply for VGA and Component

signal input.

VGA Setup/H Phase h.phase ?

0-200

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

Apply for VGA and Component

signal input.

VGA Setup/V Start v.pos ?

0-200

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

Apply for VGA and Component

signal input.

Aspect Ratio aspect ?

0 = 5:4

1 = 4:3

2 = 16:10

3 = 16:9

4 = 1.88

5 = 2.35

6 = Auto

7 = Native

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

When the Zoom function is set to

Zoom in, the Unscaled function is

disabled.

Overscan zoom ?

0 = Off

1 = On

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

When the Zoom function is set to

Zoom in, the Unscaled function is

disabled.

DU6675 DLP Projector Remote Communication Manual

Background no.signal ?

0 = Blue

1 = Black

2 = Logo

Not applicable when the project is in

standby mode

SETUP

OSD Function Operation

command Settings/Return Values Note

Language lang ?

0 = English

1 = French

2 = Spanish

3 = German

4 = Portuguese

5 = Chinese Simplified

6 = Chinese Traditional

7 = Japanese

8 = Korean

Lamp Mode lamps ?

0 = Dual

1 = Lamp1

2 = Lamp2

3 = Single



Not applicable when the project is

in standby mode



Not applicable when the project is

in cooling or lighting up status.

Please send control command

after the said commands are

completed.

Lamp Power lamp.mode

0 = Standard

1 = Economy

2 = Custom Power Level

Not applicable when the project is in

standby mode

Custom Lamp Power lamp.pwr ?

0-31 (75 % ~ 100.0 %)

Not applicable when the project is in

standby mode

Keystone v.keystone ?

-80 ~ 80

Not applicable when the projector is

in standby mode.

Keystone h.keystone ?

-80 ~ 80

Not applicable when the projector is

in standby mode.

Startup Logo

startup.logo ?

0 = Off

1 = On

Trigger trig.1 ?

0 =Off

1 = On

Not applicable when the projector is

in standby mode.

Remote sensor remote.sensor ?

0 = Front / Back

1 = Front

2 = Back

3 = HDBaseT

Not applicable when the projector is

in standby mode.

DU6675 DLP Projector Remote Communication Manual

INSTALLATION

OSD Function Operation

command Settings/Return Values Note

Projection Mode proj.mode ?

0 = Desktop Front

1 = Desktop Rear

2 = Ceiling Front

3 = Ceiling Rear

Not applicable when the project is in

standby mode

Standby Mode

eco.net.pow ?

0 = Network Standby

1 = Normal (< 0.5W ECO

Mode)

Not applicable when the project is in

standby mode

High Altitude altitude

0 = Off

1 = On

Not applicable when the project is in

standby mode

Auto Power Off

auto.powoff ?

0 = Off

1 = On

Not applicable when the project is in

standby mode

Auto Power On

auto.powon ?

0 = Off

1 = On

Not applicable when the project is in

standby mode

Network/IP Adress

net.ipaddr ?

Not applicable when the project is in

standby mode

Network/Subnet

net.subnet ?

Not applicable when the project is in

standby mode

Network/Gateway

net.gateway ?

<string> Not applicable when the project is in

standby mode

Network/DHCP

net.dhcp ?

0 = Off

1 = On

Not applicable when the project is in

standby mode

Zoom zoomio +

“+” = Zoom out

“-“ = Zoom in

The Lens control command does not

apply when the projector is in

standby mode.

Focus focus +

“+” = Focus Near

“-“ = Focus Far

The Lens control command does not

apply when the projector is in

standby mode.

Shift V vert.offset +

“+” = Shift up

“-“ = Shift dwon

The Lens control command does not

apply when the projector is in

standby mode.

Shift H horiz.offset +

“+” = Shift right

“-“ = Shift left

The Lens control command does not

apply when the projector is in

standby mode.

Test Pattern pattern ?

0 = Color Bar

1 = Cross Hatch

2 = Burst

3 = HRamp

4 = Red (uncorrected)

5 = Green (uncorrected)

6 = Blue (uncorrected)

7 = White (uncorrected)

8 = Black (uncorrected)

9 = Off

Not applicable when the project is in

standby mode.

DU6675 DLP Projector Remote Communication Manual

SERVICE

OSD Function Operation

command Settings/Return Values Note

Model model ? <String>

Serial Number ser.no ? <String>

Software Version sw.ver ? <String>

Pixel Clock pixel.clock ? <String> In unit of MHz

Not applicable when the project is

in standby mode or the input signal

is not locked yet.

H Refresh Rate h.refresh ? <String> Not applicable when the project is in

standby mode or the input signal is

not locked yet.

V Refresh Rate v.refresh ? <String> Not applicable when the project is in

standby mode or the input signal is

not locked yet.

Lamp1.Time lamp1.hours ? <String>

Lamp2.Time lamp2.hours ? <String>

Power On Time proj.runtime ? <String>

Lamp 1 Status

lamp1.stat ? 0 = Off

1 = On

Not applicable in standby mode

Lamp 2 Status

lamp2.stat ? 0 = Off

1 = On

Not applicable in standby mode

Factory Reset fact.reset (execute)

Others

OSD Function Operation

command Settings/Return Values Note

Power On power.on (execute) Not applicable in standby mode

Power Off power.off (execute) Not applicable in standby mode

Projector Status status ? 0 = standby

1 = warm up

2 = imaging

3 = cooling

4 = reset

Note: The projector returns string "NA" when the input command does not apply to current projector status or setup.

Andere Handbücher für DU6675

Inhaltsverzeichnis

Andere Vivitek Projektor Handbücher

Vivitek

Vivitek D7 Series Bedienungsanleitung

Vivitek

Vivitek D4500V Bedienungsanleitung

Vivitek

Vivitek DU8090Z Gebrauchs- und Pflegehandbuch

Vivitek

Vivitek D5500 series Bedienungsanleitung

Vivitek

Vivitek D851 Bedienungsanleitung

Vivitek

Vivitek H1188 Series Bedienungsanleitung

Vivitek

Vivitek D5000 Bedienungsanleitung

Vivitek

Vivitek DU8193Z Bedienungsanleitung

Vivitek

Vivitek H5095 series Bedienungsanleitung

Vivitek

Vivitek D5010-WNL Bedienungsanleitung

Vivitek

Vivitek DU9900Z Bedienungsanleitung

Vivitek

Vivitek H1082 Bedienungsanleitung

Vivitek

Vivitek DU9000 Bedienungsanleitung

Vivitek

Vivitek DU4371Z-ST Bedienungsanleitung

Vivitek

Vivitek DX881ST Bedienungsanleitung

Vivitek

Vivitek D8300 Series Bedienungsanleitung

Vivitek

Vivitek HK2288 Bedienungsanleitung

Vivitek

Vivitek dh6671 Bedienungsanleitung

Vivitek

Vivitek DW771USTIE Bedienungsanleitung

Vivitek

Vivitek Voyager AV200 Bedienungsanleitung

Vivitek

Vivitek D755WT SERIES Bedienungsanleitung

Vivitek

Vivitek DU8195Z Bedienungsanleitung

Vivitek

Vivitek D755WT SERIES Bedienungsanleitung

Vivitek

Vivitek DU9000 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung