Von Duprin RX S1 Bedienungsanleitung
RX/RX-LC/S1!Switch!Retrofit!Kit
Base!Plate
Assembly
➂Remove!push!bar.
Slide
to
remove
Slide
to
remove
➀!Remove!screws.
➁Remove!mechanism!case.
Dogging!assembly!may!not
be!present!on!all!devices.
Step!➊
Disassemble!the!device.!(Remove!from!door!if!mounted.)
!This!kit!includes!the!following!parts:
8-18!X!3/8"!Flat!Head!Screw!(2) Switch!Assembly Nylon!Fastener
This!switch!is!intended!for!signaling!purposes!only!and!is!rated!for!a
.1!ampere!to!3!ampere!resistive!load!at!24VDC/AC.!Use!with!inductive
or!capacitive!loads!(magnetic!locks!or!solenoid!devices)!derates!the
capacity!of!the!switch.!Consult!the!factory!for!assistance.
22!Device
Cable Tie 1.5"
INSTALLATION INSTRUCTIONS
RX{
This!switch!is!intended!for!systems!using!low!current!signals.!The!switch!is
rated!for!a!maximum!of!50mA.!Consult!the!factory!for!assistance.
RX-LC
{
Standard (RX)
or low current (RX-LC)
941038_00(4) Copyright © 2003 Ingersoll-Rand. All rights reserved.
VON DUPRIN®
Slide
to
remove
Base!Plate
Assembly
➀
Remove!mechanism!case.
➁
!Remove!push!bar.
Slide
to
remove
Dogging!assembly!may!not
be!present!on!all!devices.
If!the!push!bar!has!2!screws
for!end!cap,!replace!with!the
2!screws!provided!in!this!kit.
➂
➂Remove!push!bar.
Slide
to
remove
Base!Plate
Assembly
➁Remove!mechanism!case.
Dogging!assembly!may!not
be!present!on!all!devices.
Slide
to
remove
➀Remove. ➃If!the!push!bar!has!2!screws
for!end!cap,!replace!with!the
2!screws!provided!in!this!kit.
This!end!only
33/35!Device
33A/35A!&!98/99!Device
Page 2
Used!on!33A/35A
device!only
98/99!device
center!case!shown
Step!➌
Drill!two1/8"!holes!through!rear
guide!base!only!if!holes!are
not!present.
Step!➋
Remove!&!discard!this!bearing
strip!before!snapping!switch
assembly!onto!rear!guide!base.
Rear!Guide!Base
1!3/8"
3/8"
Step!➍
Install!Switch!Assembly.
Step!➏
Route!the!wires!from!the
switch!assembly!through
this!hole.!Wires!are!not!to
interfere!with!any!moving
parts.!Secure!wires!with
a!cable!tie.
Step!➎
Install!nylon!fastener.
Page 3
3/16"
1!7/8"
Cable!tie
Page 4
End!Cap!Mounting!Bracket
Drill!5/16"!-!5/8"!hole!in!the!door
this!side!only!using!the!end!cap
mounting!!bracket!for!location.
Connect!wires!to!power!transfer,
electric!hinge,!etc.!Refer!to
product!instructions.
Note:!Hole!is!not!necessary!for
an!alarm!kit,!refer!to!its!installation
Step!➑Prep!door!for!device!wiring.
Switch Yellow
Blue
Switch Yellow
*Red!or!Green
Blue
Depress!the!bellcrank,!the
switch!should!actuate
during!this!movement
Release!the!bellcrank,!the
switch!should!actuate
during!this!movement
If!adjustment!is!needed,!loosen
screw!in!the!side!of!the!switch
assembly!and!slide!switch!forward
or!backward!as!necessary.
RX!actuator!position
Step ➐Check!the!switch!for!proper!actuation.
*Red = 3A
Green = 50mA
*Red!or!Green
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Von Duprin Schalten Handbücher
