vonado 36719 Bedienungsanleitung
PORSCHE 911 RSR #42096 Basic Version
Package contents：
8 x 15cm Warm White Dot Lights
2 x 15cm White Dot Lights
2 x 30cm White Dot Lights
1 x 15cm Connecting Cables
1 x 30cm Connecting Cables
1 x Warm White Strip Light
1 x 6-port Expansion Board
1 x 12-port Expansion Board
1 x AAA Battery Pack
Note:
Place wires on the surface or under the building blocks.
The wire can be place between the building blocks or under the block, but they should be placed
between the studs correctly.
Insert the connectors to the ports.
Be careful when you are operating, there’s only one correct way to insert, make sure the expansion
board is upward, find the soldered “=” sign on the left of the port. When you are inserting, the side
which the wires can be seen should be faced to the “=” sign and if you feel hard to insert, please stop,
and don’t force it, for that may result in bent pins inside the port or overheating of the expansion
board.
At this point, use the tweezers to straighten the bent
pins.
When installing dot lights, make sure they are correctly placed (Yellow LED package is exposed). You
can put they either on the top of the studs or between studs.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up,
ensure the side of the connector with the wires exposed is facing down. If a
plug won’t fit easily into a port connector, don’t force it. Doing so will damage
the plug and the connector.
Finally, please pay attention to the positive and negative terminals of the
battery when installing the battery case.
OK, Let’s Begin!
Instructions for installing this kit
We’ll firstly install lights for the car
Start from the headlights
Take 4 warm white 15cm dot lights
With the lighting side facing up, secure it in place by connecting the trans round plate over
Repeat the above steps to install the other 3 dot lights, group all cables together
Reconnect the front section of the car back, thread the cables through to the inside of the car
Take another 4 warm white 15cm dot lights, repeat the previous steps for the headlights at the left
side
Turn the car over to its side, take a 12-port expansion board, connect all cables to it
Take a 30cm connecting cable, connect it to the 12-port expansion board
Stick tapes at both sides of the expansion board, tuck excess cables around the board, then, stick the
expansion board to the inside of the car
Take the AAA battery pack, inserted with batteries
Turn the battery pack on to verify the current
Pull the 30cm cable through the interior of the car into the cab
Take a warm white strip light, a 15cm connecting cable, a 6 socket, connect as shown below
Connect the strip light to the cable in the cab and paste it on the roof
Pull the 6-seat socket into the trunk
Take 2 white 15cm dot lights
Now, move onto installing the taillights
With lighting side facing down, thread the light through the trans red piece, reconnect the trans red
piece to the back of the car. Note: force to reconnect it may break the cable
Repeat the above steps to install another light
Andere vonado Beleuchtungsausrüstung Handbücher
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
