Vonets VM300-L Gebrauchsanweisung
VONETS——VM300-L/VM300-H Mini WiFi Module
1
VM300-L/VM300-H WiFi Module
Quick Setting Guide
VONETS——VM300-L/VM300-H Mini WiFi Module
2
Declaration
Copyright © 2021 Shenzhen HouTian Network Communication Technology
Co., Ltd
All rights reserved, with retained ownership
Without Shenzhen HouTian Network Communication Technology Co., Ltd written
authorization, any company or personal can’t copy, writer or translation part or all
contents. Can’t do commodity distribution for any commercial or profitable purposes
by any ways (electricity, mechanical, photoprint, record or other methods).
VONETS is the registered trademark of Shenzhen HouTian Network Communication
Technology Co., Ltd. The other all trademarks or registered trademarks mentioned in
this documents are belong to the individual owners. The product specifications and
information technology mentioned in this manual are just for reference, if any updates,
without other notice. Except for special agreements, this manual is just for user
guidance, any statements, information and so on in this manual can’t constitute the
warranty of any forms.
VONETS——VM300-L/VM300-H Mini WiFi Module
3
Chapter 1 Bridge+Repeater Mode Configuration
Instruction
1.1 Device Connection
Power on VM300-L/VM300-H by 5V/1A power supply, then connect to PC, there are two
connection ways as below:
A. Computer is wired connected to LAN port of VM300-L/VM300-H;
（Recommend Method）
B. The computer wirelessly connects to the WiFi signal of VM300-L/VM300-H, its
default hotspot parameters are as follows:
WiFi SSID
WiFi Password
VONETS_2.4G_****
12345678
(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.)
1.2 Bridge+Repeater Application Configuration
The configuration steps of VM300-L/VM300-H for WiFi repeater and WiFi bridge are
basically the same, so this manual combines the configuration instructions of the two
application modes.
1. After computer is connected to VM300-L/VM300-H, open browser, input configured
VONETS——VM300-L/VM300-H Mini WiFi Module
4
page: http://vonets.cfg (or IP: 192.168.254.254), then press Enter;
2. Input User name and Password in login page (both are “admin”), click “Login”
button to enter configured page;
3. “Scan Hotspots”, choose the source hotspots, click “Next”;
4. Input “Source WiFi hotspot password”, click “Apply”;
IP layer transparent transmission (factory default), transparent transmission of IP
layer data, can meet most of WiFi bridge applications;
MAC layer transparent transmission, transparent transmission of all data above
the MAC layer (link layer) and MAC layer, including IP layer data. MAC transparent
transmission can solve some special applications for MAC layer encryption, such as
GoPro camera, Cisco AP, Hikvision monitoring system, etc;
The option “The configuration parameters of WiFi repeater security is
synchronized with source hotspot”is default ticked, it means the SSID of
VONETS repeater is associated with the SSID of the source hotspot, and the WiFi
password is the same as the password of the source hotspot;
Disable hotspot, if you select “Disable hotspot”on the right side of the SSID, the
device will not transmit the corresponding hotspot and can only be used as a bridge
application;
Advanced Setting,include Hot spot authentication match mode, WiFi Signal Motion
VONETS——VM300-L/VM300-H Mini WiFi Module
5
Detection and SSA Signal strength alarm threshold,these options here can be kept
unchanged, for instructions on this option, go to www.vonets.com and download the
“V Series WiFi Bridge Advanced Features Instruction”;
5. Click “Reboot”, VM300-L/VM300-H will connect to the configured WiFi hotspot
automatically, if connection is successful, the WiFi LED light will flash quickly;
VONETS——VM300-L/VM300-H Mini WiFi Module
6
Remark 1:
LED Light Form
Model
Blue Light
Green Light
VM300-L/VM300-H
2.4G WiFi Connection Status Light
Ethernet Cable Connection Status Light
1VM300-L/VM300-H is not connected to any hotspot, WiFi connection status light will flash
quickly;
2VM300-L/VM300-H is connected to hotspot successfully, WiFi connection status light will
quick flash;
3VM300-L/VM300-H is connected to hotspot successfully, but hotspot signal strength is less
than 50% greater than 10%, WiFi status light will pause flash and flash;
4VM300-L/VM300-H is connected to hotspot failed, WiFi connection status light will flash
slowly.
1.3 AP Application Configuration
VM300-L/VM300-H can be configured as an AP application. The wireless terminal device
can connect to VM300-L/VM300-H hotspot to connect to the network; however, it is best to
change its WiFi name and password for network security.
1. Log in to the configuration page http://vonets.cfg (or IP: 192.168.254.254) in your
computer browser, both user name and password are “admin”
2. Revise WiFi name: Jump to “WiFi Repeater”---- “Basic Settings”, enter new WiFi
name in “General Hotspot SSID”, click “Apply”;
VONETS——VM300-L/VM300-H Mini WiFi Module
7
3. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi
password in “Pass Phrase”, click “Apply”;
4. “WiFi Tx Power”of VM300-L/VM300-H can be changed, jump to “WiFi
Repeater”---- “Basic Settings”, choose suitable transmit power, then click
“Apply”;
5. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”,
when it is finished, all revised options will take effort.
Remark 2: When VM300-L/VM300-H connect to external network, its IP address will be
changed. At this time, when log in configured page, we suggest you enter configured domain
VONETS——VM300-L/VM300-H Mini WiFi Module
8
name: http://vonets.cfg. Or in Windows command window, enter the command: ping
vonets.cfg, to get the IP address of the device, then log in configuration page by this IP
address.
Chapter 2 Router Mode Configuration Instruction
2.1 Change device mode
1. Power on VM300-L/VM300-H by 5V/1A power supply, then connect to PC, there are
two connection ways as below:
A. Computer is wired connected to LAN port of VM300-L/VM300-H;
（Recommend Method）
B. Computer wirelessly connects to the WiFi signal of VM300-L/VM300-H, its default
hotspot parameters are as follows:
WiFi SSID
WiFi Password
VONETS_2.4G_****
12345678
(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.)
2. After computer is connected to VM300-L/VM300-H, open browser, input configured
page domain name: http://vonets.cfg (or IP: 192.168.254.254), then press Enter;
VONETS——VM300-L/VM300-H Mini WiFi Module
9
3. Enter User name and Password in login page (both are“admin”
), click“Login”button
to enter configured page;
4. In “Operating Mode”, change Device mode to “Router”mode, click “Apply”
button;
5. Reboot device: go to “System Settings”-- “Reboot Device”, click “Reboot”
button, VM300-L/VM300-H will automatically switch to router mode.
VONETS——VM300-L/VM300-H Mini WiFi Module
10
2.2 WAN port setting
2.2.1 WAN/LAN exchange
In routing mode, the Ethernet port of VM300-L/VM300-H is divided into a WAN port and
a LAN port, and WAN/LAN can be interchanged.
2.2.2 WAN Port connection method
By setting the WAN port of the router, you can change the network connection type
according to the actual needs of the individual, there are three types of WAN port
connections commonly used in the routing mode of the VM300-L/VM300-H: DHCP(Auto
Config), PPPoE(ADSL) and WiFi. DHCP and PPPoE are wired connections, and the WAN
port needs to be connected to the source network through a wired connection:
DHCP(Auto Config): WAN port connection type is selected as “DHCP(Auto
Config)”, VM300-L/VM300-H will automatically obtain IP address from source
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Vonets WLAN-Router Handbücher
