Vortech MAXFLOW 5A102-036 Bedienungsanleitung

DP/N: 007135v1.2 10/28/2018

MAXFLOW®FUEL PUMP BOOSTER

Installation Instructions

1650 Pacific Avenue, Channel Islands, CA 93033-9901 • Phone (805) 247-0226

Fax: (805) 247-0669 • www.vortechsuperchargers.com • M-F 7:00 AM - 3:30 PM (PST)

ENGINEERING, INC.

2015-2018 MUSTANG GT

P/N: 5A102-036

* Legal in California only for racing vehicles which may never be used or registered or licensed for use upon a highway.

DP/N: 007135v1.2, 2018-10-24

FOREWORD

Take note of the following before proceeding:

1. Proper installation of this accessory requires general automotive

mechanic knowledge and experience. Please browse through each step

of this instruction manual prior to beginning the installation to determine if

you should refer the job to a professional installer/technician. Please con-

tact your dealer or Vortech Engineering for possible installers in your

area.

2. This product was designed for use on stock (un-modified, OEM)

vehicles. The PCM (computer), engine, transmission, drive axle

ratios and tire O.D. must be stock. If the vehicle or engine has been mod-

ified in any way, check with Vortech prior to installation and use of this product.

3. Use only premium grade fuel with a minimum of 91 octane (R+M/2).

4. Always listen for any sign of detonatlion (knocking/pinging) and discontinue hard

use (no boost) until the problem is resolved.

5. Vortech is not responsible for any clutch, transmission, drive-line or engine dam-

age.

Exclusions from Vortech warranty coverage considerations

include, but not limited to:

1. Neglect, abuse, lack of maintenance, abnormal operation or improper installation.

2. Continued operation with an impaired vehicle or sub-system.

3. The combined use of Vortech components with other modifications such as, but

not limited to, exhaust headers, aftermarket camshafts, nitrous oxide, third party

PCM programming or other such changes.

another language in any form, by any means without written permission of Vortech Engineering, Inc.

All information, illustrations and specifications contained herein are based on the latest

product information available at the time of this publication. Changes to the manual may be

made at any time without notice. Contact Vortech Engineering for any additional informa-

tion regarding this kit and any of these modifications at (805) 247-0226 7:00am-3:30pm

PST.

STOP

DP/N: 007135v1.1, 2018-10-24

iii

TABLE OF CONTENTS

FOREWORD ...................................................ii

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

TOOL & SUPPLY REQUIREMENTS .................................iv

PARTS LIST ................................................... v

1. PREPARATION AND REMOVAL ...........................................1

2. FUEL PUMP BOOSTER INSTALLATION .....................................5

3. INTERIOR RE-ASSEMBLY................................................7

4. FINAL CHECK..........................................................9

DP/N: 007135v1.2, 2018-10-24

VORTECH FUEL PUMP BOOSTER

Installation Instructions

2015-2018 MUSTANG GT

Before beginning this installation,

please read through this entire instruction booklet

The Vortech 2015-2018 Mustang GT Fuel Pump Booster (FPB) upgrade was designed

specifically for use on 2015-2018 Ford Mustang GT vehicles equipped with a turbo-

charger, supercharger or nitrous oxide, to support applications with increased horsepow-

er over the basic kit. As with any power enhancing product, this unit is intended for use

on healthy, well-maintained engines. Vortech Engineering is not responsible for engine

damage. Installation on new vehicles will not harm or adversely affect the break-in peri-

od so long as factory break-in procedures are followed.

For best performance and continued durability, please take a note of the following key

points:

1. Use only premium grade fuel 91 octane or higher (R+M/2).

2. Always listen for any sign of detonation (pinging) and discontinue hard use (no

boost) until problem is resolved.

TOOL & SUPPLY REQUIREMENTS:

• Interior Panel Removal Tools

• Drill Motor

• #4 or 7/32" Drill Bit

• 1/4" Drive Ratchet

• 1/4" Drive Extension

• 1/4" Drive 3/8" Socket

• 1/4" Drive 10mm Socket

• 5/32 Allen Key

DP/N: 007135v1.1, 2018-10-24

PARTS LIST

2015-2018 MUSTANG GT

FUEL PUMP BOOSTER UPGRADE

Part No. 5A102-036

PART NO. DESCRIPTION QTY

007135 INSTR, ‘15-'18 MUST GT, PNP FPVB UPGRD 1

008601 BOX, CARDBOARD, PUMP BOOSTER 1

008602 INSERT, CARDBOARD, PUMP BOOSTER 1

4FQ010-090 MNTG PLT, ’15 MUST GT, FPVB 1

5A002-030 VOLT BOOSTER, PNP, STD, VORT LOGO 1

5W001-098 HARNESS, FPVB, PNP, ’11-’17 MUST GT 1

7C010-050 10-24 X .50 SHCS GR8 PLT 4

7E014-075 #14 X .75 HEX HD SHEETMETAL SCREW 2

7F010-024 10-24 NYLOCK NUT 4

7J010-001 WASHER, #10 FLAT, ZN PLT 4

7U100-055 TIE WRAP, 7.5" NYLON 5

IMPORTANT: Before beginning installation, verify that all parts are included in the kit.

Report any shortages or damaged parts immediately.

DP/N: 007135v1.2, 2018-10-24

This page was left intentionally blank.

DP/N: 007135v1.1, 2018-10-24

1. PREPARATION AND REMOVAL

Fig. 1-b: Unplug Battery Leads

B. Remove the battery cover and unplug both bat-

tery leads.

(See Fig. 1-b)

C. In order to access the fuel pump driver module,

it will be ncessary to remove the lower rear

seat cushion. There are two retainers located

underneath the front bolsters that secure the

lower rear seat cushion to the vehicle.

(See Fig. 1-c)

Fig. 1-c: Rear Seat Retainer Location

LOWER REAR SEAT CUSHION

RETAINER LOCATION

(LOCATED UNDERNEATH)

A. Prior to unplugging the battery, you will need to

roll down both windows. This is done to prevent

potential window damage as both windows rest

within a channel in the body of the vehicle

when they are rolled up.

(See Fig. 1-a)

Fig. 1-a: Roll Down Windows

NOTE: The provided mounting bracket for the fuel

pump booster is not compatible with con-

vertible vehicles at this time. Please con-

sult your local fabricator for a custom solu-

tion.

DP/N: 007135v1.2, 2018-10-24

1. PREPARATION AND REMOVAL, cont'd

E. Located near the driver side rear interior panel

is the fuel pump driver module. Unplug the

electrical connector at this time.

(See Fig. 1-e)

F. Locate the upper rear seat release strap and

fold the upper rear seat down.

(See Fig. 1-f)

Fig. 1-e: Unplug Fuel Pump Driver Module

UPPER REAR

SEAT RELEASE

STRAP

Fig. 1-f: Fold Upper Rear Seat Down

D. In order to release the lower rear seat cushion

from the vehicle, press the retainer lever

inwards then pull the lower rear seat cushion

upwards.

(See Fig. 1-d)

Fig. 1-d: Rear Seat Retainer

PUSH RETAINER

LEVER INWARDS

DP/N: 007135v1.1, 2018-10-24

1. PREPARATION AND REMOVAL, cont'd

G. Detach the rear seatbelt guide from the driver

side rear interior panel. The seatbelt passes

through the rear seatbelt guide, so it can

remain in the vehicle.

(See Fig. 1-g)

H. Remove the interior panel directly above the

driver side door sill by pulling it upwards,

releasing the retainer clips.

(See Fig. 1-h)

Fig. 1-h: Remove Interior Panel Above Driver

Side Door Sill

I. The driver side rear interior panel needs to be

removed. To remove, pull from the top of the

panel and pull away from the window. Work

your way around the panel to release all of the

retaining clips.

(See Fig. 1-i)

Fig. 1-g: Detach Small Plastic Trim

Fig. 1-i: Remove Driver Side Rear Interior Panel

DP/N: 007135v1.2, 2018-10-24

K. Remove the two metal clips securing the insu-

lation block. Discard the insulation block and

two metal clips as they will not be reused.

(See Fig. 1-k)

REMOVE 2x

METAL CLIPS

Fig. 1-k: Remove Foam Insulation Block

1. PREPARATION AND REMOVAL, cont'd

J. Locate the driver side rear interior panel & lay

it down as shown. There is a foam insulation

block that needs to be removed to make space

for the fuel pump booster.

(See Fig. 1-j)

Fig. 1-j: Foam Insulation Block

Inhaltsverzeichnis

Andere Vortech Extender Handbücher

Vortech

Vortech MAXFLOW FPB Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung