Vox StompLab IG Bedienungsanleitung

2012

Precautions

Location

Using the unit in the following locations can result in a malfunction.

• In direct sunlight

• Locations of extreme temperature or humidity

• Excessively dusty or dirty locations

• Locations of excessive vibration

• Close to magnetic elds

Power supply

Please connect the designated AC adapter to an AC outlet of the

correct voltage. Do not connect it to an AC outlet of voltage other

than that for which your unit is intended.

Interference with other electrical devices

Radios and televisions placed nearby may experience reception

interference. Operate this unit at a suitable distance from radios

and televisions.

Handling

To avoid breakage, do not apply excessive force to the switches

or controls.

Care

If the exterior becomes dirty, wipe it with a clean, dry cloth. Do

not use liquid cleaners such as benzene or thinner, or cleaning

compounds or ammable polishes.

Keep this manual

Aer reading this manual, please keep it for later reference.

Keeping foreign matter out of your equipment

Never set any container with liquid in it near this equipment. If

liquid gets into the equipment, it could cause a breakdown, re,

or electrical shock.

Be careful not to let metal objects get into the equipment. If

something does slip into the equipment, unplug the AC adapter

from the wall outlet. Then contact your nearest VOX dealer or the

store where the equipment was purchased.

THE FCC REGULATION WARNING (for USA)

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician

for help.

If items such as cables are included with this equipment, you must

use those included items.

Unauthorized changes or modication to this system can void the

user’s authority to operate this equipment.

Notice regarding disposal (EU only)

If this symbol is shown on the product, manual, baery,

or package, you must dispose of it in the correct manner

to avoid harm to human health or damage to the

environment. Contact your local administrative body

for details on the correct disposal method. If the baery

contains heavy metals in excess of the regulated amount,

a chemical symbol is displayed below the symbol on the

baery or baery package.

IMPORTANT NOTICE TO CONSUMERS

This product has been manufactured according to strict

specications and voltage requirements that are applicable in the

country in which it is intended that this product should be used.

If you have purchased this product via the internet, through mail

order, and/or via a telephone sale, you must verify that this product

is intended to be used in the country in which you reside.

WARNING: Use of this product in any country other than that for

which it is intended could be dangerous and could invalidate the

manufacturer’s or distributor’s warranty.

Please also retain your receipt as proof of purchase otherwise

your product may be disqualied from the manufacturer’s or

distributor’s warranty.

Company names, product names, and names of formats etc. are the

trademarks or registered trademarks of their respective owners.

* All product names and company names are the trademarks or

registered trademarks of their respective owners.

Introduction

Welcome!

Thank you for adding the VOX StompLab I G Modeling Guitar

Eect Processor to your rig. Whether you’re playing live, in the

studio, or practicing with headphones, the StompLab will give

you countless hours of great sounds!

To ensure a long and trouble-free relationship with your StompLab,

please read this manual carefully. When you’ve nished reading

this manual, please keep it for future reference.

Main features

103 dierent modeling eect variations are built-in, and you

can use up to seven dierent eects simultaneously (including

noise reduction).



Use these modeling eects to create your own sounds and

store them in internal memory as one of 20 user programs.

In addition, 100 more programs are provided as presets for

immediate use.

A built-in auto chromatic tuner lets you tune while bypassed

or muted.

Front and rear panel

This section explains the switches and connectors on the

StompLab I G’s front and rear panels.

Front panel

1. CATEGORY selector

In Program select mode, use this to select the program genre and

to recall the selected genre of the program.

In Edit mode, use this to select the eect that will be edited.

Also, you can save the seings of an edited eect in a program

when [WRITE] is selected.

2. VALUE 1 knob

In Program select mode, use this knob to adjust the amplier

([AMP/DRIVE]) gain. When making this adjustment, the program/

value display will indicate the gain value and the EDIT LED and

Tuner center LED will blink.

In Edit mode, use this knob to set the rst parameter of an eect.

Also, when saving a program, use this knob to select the program

location where a set program will be saved (wrien).

3. VALUE 2 knob

In Program select mode, use this knob to adjust the amplier

([AMP/DRIVE]) output level. When making this adjustment, the

program/value display will indicate the output level and the EDIT

LED and Tuner # LED will blink.

In Edit mode, use this knob to set the second parameter of an eect.

4. EDIT button, EDIT LED

Use this buon to switch the Program select mode and the Edit

mode. The modes can be switched each time the buon is pressed.

When in the Edit mode, the EDIT LED will light up.

In Program select mode, the Value lock function turns on when

this buon is pressed and held for 2 seconds and the functionality

of the VALUE 1 and VALUE 2 knobs will be disabled. The Value

lock function is canceled when the buon is pressed and held

again for 2 seconds.

The Value lock function can only be enabled in Program select

mode.

5. Program/Value display

In Program select mode, this indicates the selected program number

and the knob value. When BYPASS/MUTE is active, the display

indicates the name of the note that you’re tuning.

In Edit mode, this indicates the eect abbreviations, parameter

values. Also, this indicates the program number that was selected

as the save location when the program is saved.

6. ,  buttons

In Program select mode, use these to select programs. The program

number will increase (decrease) each time you press the buon.

In Edit mode, use these buons to select an eect and turn it on/

o. Use them to select the program in the save location and execute

the save function when saving a program.

Also, the calibration is set when the tuner is started.

7. Tuner LED

In Program select mode, this serves as the tuner meter when

BYPASS/MUTE function is active.

In Edit mode:

• The le  LED will light up when the eect name is indicated

in the program/value display.

• The center LED will light up when the VALUE 1 knob value is

indicated in the program/value display.

• The right # LED will light up when the VALUE 2 knob value is

indicated in the program/value display.

8. Program UP/DOWN pedals

In Program select mode, use these pedals to select programs.

The program number will increase (decrease) each time you

press the pedal.

In Edit mode, use these to switch the display of the program/value

display. The display is switched in the order of “Eect Name”

↔“VALUE 1 Value” ↔ “VALUE 2 Value”.

Rear panel

1234

1. INPUT jack

Connect your guitar to this jack.

2. OUTPUT/PHONES jack

Connect this jack to your guitar amp, Mixer, Recorder or

headphones.

3. POWER button

To turn the power on or o, press and hold down this buon

for 1 second.

4. DC 9V jack

You can connect an optional AC adapter to this jack.

Setup

Installing batteries

Do not mix new baeries and used baeries or dierent types

of baeries together.

Remove the 4 screws from the rubber feet that secure the

boom cover.

2. Insert four AA-size baeries, being sure to observe the correct

polarity (“+” and “-” markings), and close the boom cover.

If the baery level becomes low, noise may be generated.

Basic connections

Be sure to connect all cables with the power turned o. If you

fail to use caution when connecting cables, you could damage

your guitar amp or speaker system, or cause other malfunctions.

1. Use a cable to connect the StompLab’s OUTPUT/PHONES jack

to your guitar amp,mixer or recorder.

When connecting cables or turning on the power, make sure

to lower the volume of your amp or mixer so that you don’t

hear noise

If you’re using headphones, plug them into the OUTPUT/

PHONES jack.

If you’re using the optional AC adapter, connect it to the

rear panel DC9V power supply jack, and then plug the

adapter into an AC outlet to turn the power on.

2. Connect your guitar to the rear panel INPUT jack.

3. Press and hold the power buon and release the switch when

the program/value display lights up.

When the StompLab starts, the program/value display will

indicate the program number.

Raise the volume of your amp or mixer to the appropriate volume.

Example of a connection

Guitar amp, Mixer, Recorder

Headphone. etc.

AC adapter

to an AC outlet

Guitar

INPUT

OUTPUT/

PHONES

DC9V

Input

StompLab

Auto Power-O function

The StompLab has an Auto Power-O function that automatically

turns o the power when one hour has elapsed since the most

recent user input. If the auto power-o function is activated,

power will not be restored even if a buon or pedal is used. Turn

the power on again.

Even if there hasn’t been any user input, the Auto Power-O

function will not engage if there is audio input present at the

INPUT jack.

The Auto Power-O function is enabled as the factory default.

Enabling the auto power-o function

While holding down the EDIT buon and Program DOWN pedal,

turn the power on.

Aer “AP” is indicated, the program/value display will indicate

“En.”

Disabling the auto power-o function

While holding down the EDIT buon and Program UP pedal,

turn the power on.

Aer “AP” is indicated, the program/value display will indicate

“dS.”

The seing to enable or disable the auto power-o function is

saved even when the power is turned o.

Program select mode

The Program select mode is where you can select and perform

with programs.

Seings for each eect are collectively called a “program.” The

StompLab has 120 programs. These programs include 100 programs

that are preset programs (00–99) and cannot be overwrien and

20 programs that are user programs (U0–U9, u0–u9) that can be

overwrien. The 100 preset programs are divided in 10 categories

with 10 programs each.

Selecting a program

1. Check whether you are in Program select mode.

In Program select mode, the Tuner

LED and  LED will light

up and the EDIT LED will turn o.

When in Edit mode, the EDIT LED will light up and it will

turn o when the EDIT buon is pressed to switch to Program

select mode.

Select a genre with the CATEGORY selector and press the

Program UP or Program DOWN pedal to select the program.

The program/value display shows the number of the program

that you selected.

3. Adjust the master volume as necessary.

)

Page 11 “Seing the type of device that you’ll be connecting

to the OUTPUT/PHONES jack and master volume - [GBL]

(GLOBAL)”.

Bypass and Mute

Bypass (which turns o all eects including noise reduction)

and Mute (which mutes the StompLabs output) are convenient

functions to use while you’re adjusting your guitar amp, tuning

during a live performance, or switching guitars. Here’s how to

use Bypass or Mute.

Bypassing the StompLab

Simultaneously press the Program UP and Program DOWN

pedals; all eects will be bypassed. At this time, the program/

value display will indicate “ – – ”.

Muting the StompLab

Simultaneously press and hold down the Program UP and Program

DOWN pedals for about one second and the output will be muted.

At this time, the program/value display will indicate “ _ _ ”.

When bypassed or muted, the Auto Chromatic Tuner will be

active. To cancel the bypass or mute function, press the Program

UP or Program DOWN pedal (this will not change the program).

Tuner

The StompLab has a built-in Auto Chromatic Tuner.

You can calibrate the reference pitch (the note “A”) of the tuner

in a range of 438Hz–445Hz.

Tuning procedure

The Auto Chromatic Tuner will be activated when the StompLab

is bypassed or muted.

If you want to tune silently, such as during a live

performance, simply mute the StompLab.

2. Play a note on your guitar and the program/value display will

indicate the name of the closest note.

Note names are indicated as follows.

C C# D D# E F F# G G# A A# B

Note name

Display

If your guitar is sharp (pitch too high), the Tuner # LED will light

up. If your guitar is at (pitch too low), the Tuner  LED will

light up. In either case, the brightness of the LEDs will indicate

how far either has veered.

When in tune, both the Tuner center LED will light up.

Adjusting the tuner calibration

You can adjust the reference pitch of the internal tuner (piano

center frequency A). You can calibrate this reference pitch in a

range of 438Hz–445Hz.

When you turn o the power, the calibration adjustment that you

made will be discarded and the StompLab will automatically

be set to 440Hz.

1. Change the reference pitch with the  or  buon. when the

tuner is starting up.

The program/value display will indicate a reference pitch

(38–45: 438–445Hz).

Creating your sound (Edit mode)

The Edit mode is where you can set the eects that are used

in each category, such as [PDL] (PEDAL), [AMP/DR] (AMP/

DRIVE), [CAB] (CABINET), [NR] (NOISE REDUCTION), [MOD]

(MODULATION), [DLY] (DELAY) and [REV] (REVERB).

Signal ow

PEDAL AMP/DRIVE (Lo - Hi)

REVERB DELAY MODULATION

NOISE REDUCTION

CABINET

Entering Edit mode

1. In Program select mode, press the EDIT buon. You will enter

the Edit mode and the EDIT LED will light up.

Selecting eects and adjusting the parameters - [PDL],

[AMP/DR], [CAB], [NR], [MOD], [DLY], [REV]

Select an eect to use in each category and set the parameter.

1. Select the category with the CATEGORY selector.

2. Select the eect with the  or  buon.

The program/value display will indicate an abbreviation of the

eect name and the Tuner  LED will light up.

For the eects and parameters that you can select, please refer

to the “Appendices” section on page 50.

When you select an eect, the StompLab automatically sets the

parameters of that eect to the most eective values.

By adjusting the parameters, you can tweak your sound to

what you have in mind.

To turn an eect on/o, press both the  and  buons

simultaneously. When an eect is on, the eect name is

shown, and when an eect is o, the display indicates “oF”.

3. Set the eect parameter with the VALUE 1 knob and VALUE

2 knob.

As you turn a knob, the program/value display will indicate

the values. For VALUE 1 the Tuner center LED will light up

and for VALUE 2 the Tuner # LED will light up.

For the eect parameters that are assigned to each knob, please

refer to the “Appendices” section on page 50.

[Lo] and [Hi] are part of the [AMP/DR] parameter. If

[AMP/DR] is turned o, the eect will be disabled. Also,

you can set the volume level of the program with the

[AMP/DR] VALUE 2 knob (LEVEL).

For noise reduction, select [NR] with the CATEGORY

selector and adjust the sensitivity with the VALUE 1

knob. Adjust the noise reduction sensitivity so that you

don’t hear noise (hiss) when you’re not playing your guitar.

Depending on the guitar that you’re using, sustaining

notes may be cut o if you raise the noise reduction value

excessively. This parameter should be adjusted so notes

ring out naturally.

Eect/parameter type and parameter value display

In the Edit mode you can switch the eect names or the VALUE 1

and VALUE 2 values indicated with the Program UP/DOWN pedals.

The tuner  LED will light up when the eect name is indicated, the

tuner center LED will light up when VALUE 1 is indicated and the

tuner # LED will light up when VALUE 2 is indicated.

Checking the values saved in a program (Original Value)

The Original Value LED in the program/value display lets you

check the parameter values of a saved program.

When you use the knob or buons to modify the value of a

parameter, the Original Value LED will light up when that value

matches the value that’s already been saved in the program (i.e.,

the original value).

In Program select mode, the Original Value LED will light up

if the values of all parameters match the values that are saved

in the program.

Saving a program — [WRITE]

Here’s how to save (write) a sound that you’ve created.

If you switch to a dierent program in Program mode or turn

o the power without writing your seings into memory, the

changes that you made will be lost.

1. Set the CATEGORY selector to [WRITE].

The program number will blink in the program/value display.

2. Use the VALUE 1 knob, the / buons or the Program UP/

DOWN pedals to select the program location where you want

to save your seings.

3. Press the  buon and  buon simultaneously for 1 second.

The program will be saved, and the program/value display

will indicate “ CP ” briey.

The newly saved program will overwrite (i.e., replace) the

existing seings, so the previous program in that location

will be lost.

To cancel saving the program, select a category other than

[WRITE] with the CATEGORY selector.

Inhaltsverzeichnis

Sprachen:

Andere Vox Musikequipment Handbücher

Vox

Vox amPlug I/O Bedienungsanleitung

Beliebte Musikequipment Handbücher anderer Marken

DAPAudio

DAPAudio IPS-PT Bedienungsanleitung

Dynacord

Dynacord DPM 8016 Bedienungsanleitung

Subdecay

Subdecay Starlight Flanger Bedienungsanleitung

Moen

Moen GEC8 Live Bedienungsanleitung

Fender

Fender 1 Bedienungsanleitung

Yamaha

Yamaha MLC-16 Bedienungsanleitung

Sonuscore

Sonuscore TIME TEXTURES Bedienungsanleitung

flight of harmony

flight of harmony V'Amp Bedienungsanleitung

NANO

NANO PERFORMANCE MIXER Bedienungsanleitung

Tascam

Tascam CD-GT2 Bedienungsanleitung

BHI

BHI NEIM 1031 MKII Bedienungsanleitung

Befaco

Befaco KICKALL Bedienungsanleitung

Paia

Paia 9720 Leitfaden

limex

limex ALPIN MASTER 128 Bedienungsanleitung

nord

nord Electro 3 Bedienungsanleitung

Joemeek

Joemeek sixQ2 Bedienungsanleitung

CARVIN

CARVIN 500W STEREO POWER MODULE - SCHEMA REV G Bedienungsanleitung

Furutech

Furutech ADL GT40 Installationsanleitung