Vox LED 39880 Bedienungsanleitung

English - 1 -

Safety Precautions

Please read these instructions fully

before installing or operating.

WARNING: Never let people (including

children) with physical, sensory or mental

abilities or lack of experience and / or knowledge

unsupervised use electrical device!

Children may not recognize dangers right!

The swallowing of batteries can be fatal. Keep

batteries always out of reach of small children.

If a battery is swallowed, immediately seek

medical attention. Keep the packaging lms out

of reach of children. Risk of suffocation.

Power source

•The TV should be operated only from a 220-240 V

AC, 50 Hz outlet.

• Warning: Do not leave your TV in standby or

operating mode when you leave your house.

Positioning the TV

•For ventilation, please leave a clear space of at least

10cm all around the TV.

• Do not block the ventilation openings.

• Do not place the TV on sloping or unstable surfaces,

the TV may tip over.

•To prevent damage to the TV, do not place any

objects on top of the TV.

•Only use the TV in moderate climates.

Power cord and plug

•The power cord plug should be easily accessible.

In case of storms and lightning, when going on

holiday, or when the TV is not used for a long period

of time disconnect the power cord from the mains

power socket.

•The mains plug is used to disconnect TV set from

the mains and therefore it must remain readily

operable.

• Do not place the TV, furniture, etc. on the power

cord or pinch the cord.

•Handle the power cord by the plug, do not unplug

the TV by pulling the power cord.

•Never touch the power cord/plug with wet hands as

this could cause a short circuit or electric shock.

•Never make a knot in the power cord or tie it with

other cords.

•Power cords should be placed in such a way that

they are not likely to be stepped on or driven over.

•Adamagedpowercord/plugcancausereorgive

you an electric shock. When damaged it must be

replaced,thisshouldonly be done by qualied

personnel.

Contents

Power source...................................................... 1

Positioning the TV............................................... 1

Power cord and plug........................................... 1

Moisture and Water ............................................ 2

Ventilation ........................................................... 2

Heat sources and Flames................................... 2

Headphone Volume ............................................ 2

Wall Mounting (optional) ..................................... 2

LCD Screen ........................................................ 2

Cleaning.............................................................. 2

Repair Information .............................................. 2

Operation with the Remote Control .................... 3

Input Selection.................................................... 3

Changing Channels and Volume ........................ 3

Switching the TV On ....................................... 6

Switching the TV Off ........................................... 6

Aerial Installation ................................................ 7

Cable Installation ................................................ 7

Media Browser Menu.......................................... 8

Sorting Channel List ........................................... 8

Programme Options.......................................... 12

Recordings Library............................................ 13

Digital Teletext (If available).............................. 14

Image persistence - ghosting............................ 14

No power .......................................................... 14

Poor picture ...................................................... 14

No picture ......................................................... 14

No sound .......................................................... 15

Remote control - does not operate .................. 15

Input sources - can not be selected.................. 15

Recording Unavailable ..................................... 15

USB Is too Slow ............................................... 15

English - 2 -

Moisture and Water

• Do not use this TV in a humid or damp place (avoid

bathrooms, the sink in the kitchen, and near the

washing machine).

•Do not expose this TV to rain or water, as this may

be dangerous.

•Do not place objects lled with liquids, such as

owervases,ontopoftheTV.Avoidfromdripping

or splashing.

•If any solid object or liquid falls into the cabinet,

unplug the TV and have it checked by qualied

personnel before operating it any further.

Ventilation

•The slots and openings on the TV set are intended

for ventilation and to ensure reliable operation.

•To prevent overheating, these openings must not be

blocked or covered in anyway.

Heat sources and Flames

• Do not expose the TV to direct

sunlight or other heat sources.

•The TV should not be placed near to

openamesandsourcesofintense

heat such as an electric heater.

•Ensure that no open ame sources,

such as lighted candles, are placed

on top of the TV.

Headphone Volume

•Excessive sound pressure from

earphones and headphones can cause

hearing loss, please take care.

Wall Mounting (optional)

•To prevent injury, this TV must be securely attached

to the wall in accordance with the installation

instructions (if the option is available).

LCD Screen

•Occasionally, a few non-active pixels may appear

onthescreenasaxedblue,greenorredpoint.

Please note that this does not affect the performance

of your product.

•Takecarenottoscratchthescreenwithngernails

or other hard objects.

Cleaning

•Before cleaning, unplug the TV from the wall

socket.

• Do not use liquid or aerosol cleaners. Only use a

soft, dry cloth.

Environmental Information

This television is designed to consume less energy

to save environment. You not only help to save the

environment but also you can save money by reducing

electricitybillsthankstotheenergyefciencyfeauture

of this TV. To reduce energy consumption, you should

take the following steps:

You can use Power Save Mode setting, located in the

Picture Settings menu. If you set Power Save Mode

as Eco, the TV will switch to energy-saving mode

and luminance level of TV set will be decreased to

optimum level. Note that some picture settings will be

unavailable to be changed when the TV is in Power

Save Mode.

If you set power save mode as Picture off, a message

will appear on the screen and backlight will be off

within three seconds. Press any button on the remote

controller to activate the picture again.

When the TV is not in use, please switch off or

disconnect the TV from the mains plug. This will also

reduce energy consumption.

Disconnect power when going away for longer time.

It is highly recommended to activate Power Save Mode

setting to reduce your annual power consumption.Also

it is recommended to disconnect the TV from the mains

plug to save energy more when you do not use.

Please helps us to save environment by following

these steps.

Repair Information

Pleasereferallservicingtoqualiedpersonnel.Only

qualiedpersonnelmustrepairtheTV.Pleasecontact

your local dealer, where you have purchased this TV

for further information.

English - 3 -

Accessories included

Remote Control

Batteries 2x AAA

Instruction Book

Side AV Connection Cable

TV - Features

•Fully integrated digital/cable (DVB-T/C).

•HDMI connectors for digital video and audio.

•USB input.

•Programmerecording.

•Programmetimeshifting.

•10000 programmes.

•OSD menu system.

•Scart socket for external devices.

•Stereo sound system.

•Teletext, fastext, TOP text.

•Headphone connection.

•Automatic programming system.

•Forward or backward manual tuning.

•Automatic power down after up to six hours.

•Sleep timer.

•Child lock.

•Automatic sound mute when no transmission.

•NTSC playback.

•AVL (Automatic Volume Limiting).

•PLL (Frequency Search).

•PC input.

•Plug&Play for Windows 98, ME, 2000, XP, Vista,

Windows 7.

•Game Mode.

•Picture off function.

Viewing the TV

TV Control Switch & Operation

1. Up direction

2. Down direction

3. Programme/Volume / AV / Standby-On selection

switch

You can move the switch, upward or downward to

change the volume. If you want to change channels,

press the middle of the switch once (Position 3) and

then move upward or downward. If you press the

middle of the switch once more,source OSD will be

displayed. To select desired source, move the switch

upward or downward and release. If you press the

middle of the switch and hold about a few seconds,

the TV will switch to standby mode. Main menu OSD

cannot be displayed via the control button.

Operation with the Remote Control

Press MENU button on your remote control to display

main menu screen. Use Left or Right button to select

a menu tab and press OK to enter. Use Left / Right

/ Up / Down to select or set an item. Press RETURN

or MENU button to quit a menu screen.

Input Selection

Once you have connected external systems to your

TV, you can switch to different input sources. Press

SOURCE button on your remote control consecutively

to select the different sources.

Changing Channels and Volume

You can change the channel and adjust the volume

by using the V ^ / v and CH ^ / v buttons on the

remote.

English - 4 -

Viewing remote control

NOTE: The Remote Control range is approximately

7m / 23ft.

1. Standby

2. Image size

3. Sleep Timer

4. Mono/Stereo - Dual I-II / Currrent Language (*)

(in DVB channels)

5. Favourite channels

6. Numeric buttons

7. Electronic programme guide(in DVB channels)

8. No function

9. Media Browser

10. Navigation buttons (Up/Down/Left/Right)

11. No function

12. No function

13. Programme Down / Page up - Programme Up /

Page down

14. Mute

15. Programme recording

16. Pause (in Media Browser mode) / Timeshift

recording

17. Rapid reverse (in Media Browser mode)

18. Play (in Media Browser mode)

19. Red button

20. Green button

21. Picture mode selecion

22. No function

23. Teletext / Mix (in TXT mode)

24. Subtitle on-off (in DVB channels)

25. Previous programme

26. AV / Source selection

27. Menu on-off

28. Okay(Conrm)/Hold(inTXTmode)/Channel

List

29. Exit / Return / Index page (in TXT mode)

30. No function

31. Info / Reveal (in TXT mode)

32. Volume Up / Down

33. No function

34. No function

35. Rapid advance (in Media Browser mode)

36. Stop (in Media Browser mode)

37. Blue button

38. Yellow button

SLEEP

SCREEN

PRESETS

LANG.

FAV

EPG SWAP

SOURCE

DISP.

MODE

INFO

CH V

English - 5 -

Viewing the Connections

NOTE: When connecting a device via the Side AV input, you must use the supplied connection cables

to enable connection. See the illustrations above. | To enable PC audio, you will need to use the supplied SIDE

AV CONNECTION cable’s WHITE & RED inputs. | If an external device is connected via the SCART socket, the

TV will automatically switch to AV mode.| When receiving DTV channels (Mpeg4 H.264) or while in Media Browser

mode, output will not be available via the scart socket. | When using the wall mounting kit (optional), we recommend

that you plug all your cables into the back of the TV before mounting on the wall. | Insert or remove the CI module

only when the TV is SWITCHED OFF. You should refer to the module instruction manual for details of the settings.

You can use the VGA input for connecting a YPbPr device. To do this, you need a YPbPr to PC cable (Not supplied).

Câble de connexion

AV (fourni)

Péritel

Branchement

ommandé)

(rec

VGA

Branchement

ommandé)

(rec

Branchement

audio PC/YPbPr

sur côté

Câble audio

du PC (Non fourni)

Câble de Connexion

Latérale Audio/Vidéo

(fourni)

Connexion

HDMI

(Recommandée)

Branchement

SPDIFF

(recommandé)

SPDIFF

Branchement

AV sur côté

Branchement

du casque

sur côté

Branchement

USB sur côté

Connecteur Type Câbles Appareil

CASQUE

Branchement

CI sur côté

CAM

module

AV SUR CÔTÉ

SIDE AV

5Vdc

Max:500mA

SIDE AV

5Vdc

Max:500mA

SIDE AV

5Vdc

Max:500mA

AV SUR CÔTÉ

(Non fourni)

English - 6 -

Installing the Batteries to the Remote

1. Lift the cover on the back of the remote upward

gently.

2. Install two AAA batteries. Make sure to match the +

and - ends of the batteries in the battery compartment

(observe the correct polarity.

3. Replace the cover.

Connect Power & Antenna/Cable

IMPORTANT: The TV set is designed to operate on

220-240V AC, 50 Hz socket. After unpacking, allow

the TV set to reach the ambient room temperature

before you connect the set to the mains. Plug the

power cable to the mains socket outlet.

SPDIF

VGA

Aerial or Cable

Switching On/Off

Switching the TV On

With power cord plug connected to the mains power

socket, the TV is in ‘Standby’ mode.

To switch the TV on from standby mode:

Press the “ ” button and the TV will switch to

standby mode. Then the standby LED lights up.

To switch on the TV from standby mode either:

a. Press the “ ” button,CH ^/ v or a numeric button

on the remote control.

b. Press the middle of the “ ” button on the TV.

By either method the TV will switch on.

Switching the TV Off

Press the “ ” button on the remote control or press

the standby “ ” button, so the TV will switch to

standby mode.

To turn off the TV completely, remove the power

cord plug from the mains power socket.

Note: When the TV is switched to standby mode, standby

LED can blink to indicate that features such as Standby

Search, Over Air Download or Timer is active. The LED

can also blink when you switch on the TV from standby

mode.

First Time Installation

When turned on for the rst time, the “language

selection” menu appears. The message “Welcome

please select your language!” is displayed in all

language options listed alphabetically.

Press the “ ” or “ ” button to highlight the

required language, press OK button to select. “First

Time Installation” appears. Use “ ” or “ ” button to

set the required country, and press “ ” button to

select Search Type (optional).

Use “ ” or “ ” to set the desired search type. Available

search types are Digital and analog, digital only and

analog only.

When set, press “ ” to select Teletext Language.

Use “ ” or “ ” to select the desired Teletext Language.

Next, select Scan Encrypted and set as Yes if you

want to scan coded stations.

Press OK button on the remote control to continue

and the following message will be displayed on the

screen.

English - 7 -

You must select a search type to search and store

broadcasts from the desired source.

Aerial Installation

If you select AERIAL option from the Search Type

screen, the television will search for digital terrestrial

TV broadcasts.

NOTE: You can press MENU button to cancel.

After all the available stations are stored, Channel

List will be displayed on the screen. If you like the

sort channels, according to the LCN(*), please select

“Yes” and than press OK.

Press OK button to quit channel list and watch TV.

(*) LCN is the Logical Channel Number system that

organizes available broadcasts in accordance with a

recognizable channel sequence.

Cable Installation

If you select CABLE option and press OK button on

the remote control to continue, the following message

will be displayed on the screen:

To continue please select YES and press OK. To

cancel operation, select NO and press OK.

You can select frequency ranges from this screen. For

highlighting lines you see, use “ ” or “ ” button.

You can enter the frequency range manually by using

the numeric buttons on the remote control.

Set Start and Stop Frequency as desired by using

numeric buttons on the remote control.

After this operation, you can set Search Step as 8000

KHz or 1000 KHz.

If you select 1000 KHz, the TV will perform search

process in a detailed way. Searching duration will

thusincreaseaccordingly.Whennished,pressOK

button to start automatic search. The TV will search

and store available broadcasts.

English - 8 -

Media Playback via USB Input

You can connect a USB hard disk drive or USB

memory stick to your TV by using the USB inputs of

theTV.Thisfeatureallowsyoutoplaylesstoredina

USB drive. 2.5” and 3.5” inch (hdd with external power

supply) external hard disk drives are supported.

IMPORTANT!Youshouldbackupyourlesbefore

making any connections to the TV set in order to

avoid any possible data loss. Manufacturer will not

beresponsibleforanyledamageordataloss.Itis

possible that certain types of USB devices (e.g. MP3

Players) or USB hard disk drives/memory sticks may

not be compatible with this TV. The TV supports

FAT32 and NTFS disk formatting but recording

will not be available with NTFS formatted disks.

Note: While formatting a USB hard disk that has 1TB

(TeraByte)ormorelecapacity,youcanexperience

problems with the formatting process.

Quickly plugging and unplugging USB devices, is a

very hazardous operation. Do not repeatedly quickly

plug and unplug the drive. This may cause physical

damage to the USB player and USB device itself. Do

notpulloutUSBmodulewhileplayingale.

Media Browser Menu

You can play photo, music, and movie les stored

on a USB disk by connecting it to your TV and using

the Media Browser screen. To do this, perform the

following: Connect a USB disk to one of the USB input

located on the side of the TV.

Press MENU button and select Media Browser tab by

using Left/Right and OK buttons. Main media browser

screen will be displayed. You can display the related

content by selecting the Video, Music or Picture tab.

Follow the button indications under each on screen

menu for media playback features.

You can set your Media Browser preferences by using

the Settings dialog.

Changing Image Size: Picture Formats

Programmes can be watched in different picture

formats, depending on the transmission received.

You can change the aspect ratio (image size) of the

TV for viewing the picture in different zoom modes.

Press SCREEN button repeatedly to change the

image size. You can shift the screen up or down

by using “ ” or “ ” buttons while in 14:9

Zoom, Cinema or Subtitle.

Using the Channel List

The TV sorts all stored stations in the Channel List.

You can edit this channel list, set favourites or set

active stations to be listed by using the Channel List

options. Press MENU button to view main menu.

Select Channel List item by using Left or Right button.

Press OK to view menu contents. Select Edit Channel

List to manage all stored channels. Use Up or Down

and OK buttons to select Edit Channel List. Press

Up or Down button to select the channel that will be

processed. Press Left or Right button to select a

function on Channel List menu. Use P+/P- buttons to

move page up or down. Press MENU button to exit.

Sorting Channel List

You can select broadcasts to be listed in the channel

list.Todisplayspecictypesofbroadcast,you

should use Active channel list setting. Select Active

channel list from the Channel list menu by using “

” or “ ” button. Press OK button to continue. You

can select a network type option from the list by

using “ ” or “ ” and OK buttons.

English - 9 -

Menu Features and Functions

Picture Menu Contents

Mode For your viewing requirements, you can set the related mode option. Picture mode

can be set to one of these options: Cinema,Game,Dynamic and Natural.

Contrast Sets the lightness and darkness values of the screen.

Brightness

Sets the brightness value for the screen.

Sharpness Sets the sharpness value for the objects displayed on the screen.

Colour Sets the colour value, adjusting the colors.

Power Save

Mode

To set Power Save Mode as Eco, Picture Off and Disabled. See the section,

“Environmental Information” in this manual for further information on Power Save

Mode.

Backlight

(optional)

This setting controls the backlight level and it can be set to Auto, Maximum,

Minimum and Eco Mode. Backlight function will be inactive if Power Save Mode

is set to On. Backlight cannot be activated in VGA, Media Browser mode or while

the picture mode is set to Game.

Noise

Reduction

If the broadcast signal is weak and the picture is noisy, use Noise Reduction setting

to reduce the noise amount. Noise Reduction can be set to one of these options:

Low, Medium, High or Off.

Advanced Settings

Dynamic

Contrast

You can change contrast rate by using dynamic contrast function. Dynamic

contrast can be set to one of these options: Low, Medium, High or Off.

Colour Temp Sets the desired colour tone.

Picture Zoom Sets the picture size to Auto,16:9, Subtitle,14:9, 14:9 Zoom, 4:3 or Cinema.

HDMI True

Black(optional)

While watching from HDMI source, this feature will be visible in the Picture Settings

menu. You can use this feature to enhance blackness in the picture.

Film Mode

(optional)

Films are recorded at a different number of frames per second to normal television

programmes. Turn this feature on when you are watching lms to see the fast

motion scenes clearly.

Skin Tone Adjust the desired skin tone.

Colour Shift

Adjust the desired colour tone.

RGB Gain Press OKbuttontoeditRGBgain.Youcancongurethecolourtemperaturevalues

using the RGB Gain feature.

Reset Resets the picture settings to factory default settings.

Autoposition

(in PC mode) Automatically optimizes the display. Press OK to optimize.

H Position (in

PC mode)

This item shifts the image horizontally to right hand side or left hand side of the

screen.

V Position (in

PC mode) This item shifts the image vertically towards the top or bottom of the screen.

Dot Clock (in

PC mode)

Dot Clock adjustments correct the interference that appear as vertical banding in dot

intensive presentations like spreadsheets or paragraphs or text in smaller fonts.

Phase (in PC

mode)

Depending on the resolution and scan frequency that you input to the TV set, you

may see a hazy or noisy picture on the screen. In such a case you can use this item

to get a clear picture by trial and error method.

While in VGA (PC) mode, some items in Picture menu will be unavailable. Instead, VGA mode settings will be added

to the Picture Settings while in PC mode.

Inhaltsverzeichnis

Andere Vox Fernseher Handbücher

Vox

Vox T2 LED 32YD707 Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Philips

Philips Colour Television Bedienungsanleitung

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung