Vulkan LOKRING HMRK-L Bedienungsanleitung
VERSION 1.0
LOKRING®HAND ASSEMBLY TOOLS
INSTRUCTION MANUAL HMRK-L, HMRK-V, MZ & MZ-V
.
VERSION 1.0
CONTENTS
1.0 NOTICES 02
1.1 EXPLANATION OF SYMBOLS 02
1.2 INTENDED USE 02
1.3 LIMITATION OF LIABILITY 03
1.4 SCOPE OF DELIVERY 03
1.5 WARRANTY TERMS 03
1.6 MANUFACTURER 03
1.7 PRODUCT DESCRIPTION 04
2.0 SAFETY 05
3.0 USE 06
3.1 BEFORE FIRST USE 06
3.2 ASSEMBLY JAWS 06
3.3 INSERTION OF THE ASSEMBLY JAWS 07
3.4 HMRK-V AND MZ-V 07
3.5 ASSEMBLY OF LOKRING CONNECTORS TYPE 00 07
3.6 ASSEMBLY OF LOKRING CONNECTORS TYPE 50 08
4.0 MAINTENANCE, CARE, AND DISPOSAL 09
4.1 STORAGE 09
4.2 CLEANING 09
4.3 DISPOSAL 09
5.0 EXAMPLES AS ASSEMBLY AID 10
6.0 PARTS LISTS WITH OVERVIEW DRAWING 12
6.1 HMRK-L 12
6.2 HMRK-V 14
6.3 MZ 16
6.4 MZ-V 18
ONLINE SERVICE 22
IMPRINT 23
02 |LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL VERSION 1.0
The illustrations in this manual are provided for purposes of basic understanding and can deviate
from the actual version. The usual procedures, such as wearing suitable work clothing when work-
ing with the product, are presumed to be known. Subject to change without notice.
1.0 NOTICES
Safety notices are indicated by symbols in this operating manual. The safety notices are introduced
by signal words that express the scope of the hazard. The safety notices must be strictly complied
with, you must act prudently to prevent accidents, personal injury, and material damage.
1.1 EXPLANATION OF SYMBOLS
Read the instruction manual carefully all the way through before using the
device and keep this manual on hand for the entire service life of the product!
IMPORTANT!
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
DANGER!
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
WARNING!
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
CAUTION!
The hand assembly tools are specially developped for assembling LOKRING tube connections.
1.2 INTENDED USE
LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL |03
VERSION 1.0
1.3 LIMITATION OF LIABILITY
The scope of delivery includes:
• 1 x LOKRING hand assembly tool
1.4 SCOPE OF DELIVERY
The warranty terms are included in the manufacturer’s General Terms & Conditions.
1.5 WARRANTY TERMS
VULKAN Lokring Rohrverbindungen GmbH & Co. KG
Heerstrasse 66, 44653 Herne, Germany
Tel.: +49 2325-922-155
Fax. +49 2325 51222
Email: [email protected]
1.6 MANUFACTURER
All information and instructions in this man-
ual have been provided under due considera-
tion of applicable guidelines, the current state
of technology, as well as our many years of
knowledge and experience.
The manufacturer assumes no liability for
damages arising from:
• Failure to comply with the instructions
in the manual
• Non-intended use
• Deployment of untrained personnel
• Unauthorized modifications
• Technical changes
• Use of non-approved spare parts
The actual scope of delivery can vary from
the explanations and graphic representations
provided in this manual in the case of special
versions, if supplemental order options are
desired, or on the basis of the latest
technical changes.
The agreed obligations in the delivery con-
tract, the general terms and conditions, as
well as delivery conditions of the manufactur-
er, and the statutory regulations valid at the
time the contract was concluded, apply.
BB
AA
D
F
G
E
G
C
04 |LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL VERSION 1.0
Type HMRK-L HMRK-V MZ MZ-V
Dimensions 400 x 70 x 45 mm 400 x 70 x 45 mm 400 x 70 x 45 mm 400 x 70 x 45 mm
15.75" x 2.76" x 1.77" 15.75" x 2.76" x 1.77" 15.75" x 2.76" x 1.77" 15.75" x 2.76" x 1.77"
Weight 1 kg (35.27 oz.) 1.2 kg (42.33 oz.) 1.5 kg (52.91 oz.) 1.7 kg (59.97 oz.)
For ø up to 16 mm (5/8") 16 mm (5/8") 35 mm (1 3/8") 35 mm (1 3/8")
There are 4 different versions of the hand assembly tool:
The hand assembly tools HMRK-L and HMRK-V are very light and especially designed for
assembling LOKRING connectors type 00. They are only suitable for tube connections to a
maximum ø of 16 mm (5/8"). The hand assembly tools HMRK-V and MZ-V have arms that
can be angled to enable use in areas that are difficult to access. The intended use of the hand
assembly tool is to assemble LOKRING tube and hose connections. These connections must only
be assembled with the intended (interchangeable) assembly jaws (A). A different use, such as use
as an impact tool or lever tool, is not permitted.
1.7 PRODUCT DESCRIPTION
HMRK-L HMRK-V MZ MZ-V
*Only for HMRK-V and MZ-V
Item Designation
AAssembly jaw
BBolt for assembly jaw
C* Pawl
DFixing pawl
EAssembly arm
FHolding arm
GHandle
LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL |05
VERSION 1.0
2.0 SAFETY
DANGER! DANGER OF INJURY! Severe injury is the result!
Hold the tool with both hands in such a manner that the possibility
of injury due to the jaws moving together is excluded.
DANGER!
WARNING! DANGER OF INJURY! Severe injury is the result!
For all tasks with the hand assembly tool the relevant safety
regulations, in particular the accident prevention regulations issued by
the employers’ liability insurance associations must be complied with.
WARNING!
WARNING! DANGER OF INJURY! Severe injury is the result!
Non-intended use of the hand assembly tool, such as “use as an impact tool
or lever tool” can entail severe injuries and consequently is not allowed.
WARNING!
WARNING! DANGER OF INJURY! Severe injury is the result!
The hand assembly tools are intended for the manual operation of one person.
NEVER connect the pliers to a drive! Through excessive strain parts can be
destroyed and cause injuries.
DANGER!
WARNING! DANGER OF INJURY! Severe injury is the result!
If there are indications of irregular function and performance,
stop using the tool immediately and service or repair the tool.
WARNING!
06 |LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL VERSION 1.0
Take the hand assembly tool out of its packaging. A thin film of oil has been applied to the hand
assembly tool. Remove excess oil with a lint-free cloth. Open and close the hand assembly tool
a few times to check the functionality of the hand assembly tool.
3.0 USE
3.1 BEFORE FIRST USE
The assembly jaws up to tube size ø 16 mm (5/8") are suitable for all hand assembly tools.
Larger assembly jaws can only be used in the hand assembly tools MZ or MZ-V. There are two
different types of LOKRING connectors 00 and 50:
3.2 ASSEMBLY JAWS
LOKRING TYPE 00 LOKTOOL MB
For type 00 (e.g. LOKRING 8 NK Ms 00) the assembly jaw without MB EVP designation is used
(e.g. LOKTOOL MB 8). An overview of which assembly jaw is required for which LOKRING connec-
tor is provided in the current catalog. Select the appropriate assembly jaw depending on type and
size in the current catalog and only use this jaw.
LOKRING TYPE 50 LOKTOOL MB EVP
For the LOKRING connectors type 50 (e.g. LOKRING 16 NK Ms 50) the assembly jaw with the
MB EVP designation is used (e.g. LOKTOOL MB 16 EVP).
D
F
LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL |07
VERSION 1.0
3.3 INSERTION
OF THE ASSEMBLY JAWS
Insert the suitable assembly jaws
as shown. Attention! Always insert
bolts from the proper side. If you
hold the tool as shown, insert the
left bolt from the front and the
right bolt from the rear.
3.4 HMRK-V AND MZ-V
Only type HMRK-V and MZ-V:
The angle of the holding arm (F)
can be adjusted in accordance with
installation conditions. By loosening
the fixing pawl (D) the holding
arm (F) can be set in three different
angles. Attention! Fixing pawl (D)
again be locked in place!
LOKRING TYPE 00
LOKTOOL MB
Place the tool on the tube
connection as shown.
Both rings of the LOKRING
connector are assembled
simultaneously.
3.5 ASSEMBLY OF LOKRING
CONNECTORS TYPE 00
>
08 |LOKRING HAND ASSEMBLY TOOL INSTRUCTION MANUAL VERSION 1.0
F
E
C
Open and close the assembly
arm (E) until the tube connection
is correctly assembled. To
release the hand assembly tool,
completely open the assembly
arm (E) so that the pawl (C) is
not engaged in the sprocket, and
the assembly jaws have opened
again. Comment: If at assembly,
sufficient work travel of the
assembly arm (E) is not available,
the work range can be enlarged by
adjusting the holding arm (F). See
chapter 3.4 HMRK-V and MZ-V.
F
E
C
Open and close the assembly
arm (E) until the tube connection
is correctly assembled. To
release the hand assembly tool,
completely open the assembly
arm (E) so that the pawl (C) is
not engaged in the sprocket, and
the assembly jaws have opened
again. Comment: If at assembly,
sufficient work travel of the
assembly arm (E) is not available,
the work range can be enlarged by
adjusting the holding arm (F). See
chapter 3.4 HMRK-V and MZ-V.
LOKRING TYPE 50
LOKTOOL MB EVP
Place the tool on the tube
connection as shown.
Each ring of the LOKRING
connector should be assembled
separately.
3.6 ASSEMBLY OF LOKRING
CONNECTORS TYPE 50
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Vulkan Elektrowerkzeuge Handbücher
