Vutlan VT460 Bedienungsanleitung

VT460 / Smoke, humidity, temperature sensor

Physical description

From the picture above:

Temperature & humidity sensor

CAN bus ports

Pinheads (3 pins)

LED (More info in "LEDs section" in the article: )CAN devices connection

Installation procedure

Notes on assembly

It is vital to ensure that the smoke alarm is always assembled with the sensor head pointing downwards. In any other

position, there is no guarantee that smoke will be detected.

The smoke alarm must also be positioned so that it is ventilated with an adequate amount of air and the ventilation

slots are not covered.

Installation with the mounting plate provided

The sensor is installed using the mounting plate provided.

The sensor can not be used on its own. It must be used together with Vutlan monitoring systems.

Uncover the smoke detector head from the base.

Attach smoke sensor base to the mounting plate using the M4 x 10 screws provided.

Replace the sensor head onto the base and secure it by twisting until it locks home.

Secure the mounting plate to the enclosure frame using the 4.8 x 19 screws.

Remove the red protective cap!

Drawings

Connecting sensor

Connect one end of the RJ11 / RJ12 cable to the monitoring unit CAN port and the other end to any CAN input of smoke

sensor. It is possible to connect up to 10 sensors on one CAN port. To do so connect a new RJ11 cable to a free input of an

already connected smoke sensor and the other end to the next smoke sensor in a chain. See the picture below. RJ11 or RJ12

cable pinouts can be found in the picture below. After the system will start, configure the CAN bus, after configuration, the LED

on the smoke detector will blink dimly once a second.

Using the pictures below, install a jumper on VT460.

a) For all sensors except the last sensor in the chain put "pinhead jumper" on pins: 2 and 3. TR is OFF.

b) For the last sensor in the chain put "pinhead jumper" on pins: 1 and 2. TR is ON.

Connecting CAN sensors

CAN sensors and CAN units connection

Connect CAN devices to any port CAN1 or CAN2 on the monitoring system using a cable supplied. CAN sensors can also

be connected to the port of another CAN sensor or CAN unit which is connected to the CAN bus. Determination of the

devices and their connection is done through a web interface.

The TR should be "ON" for the last sensor on each bus "CAN 1" and "CAN 2". See section "TR" below.

You can connect up to a maximum of x12 CAN sensors and CAN devices together on one CAN bus

(approximately)!

If you want to connect more than x12 CAN units, you need to use CAN-12V-1A / CAN Power Supply

This procedure applies to the following sensors, which are supported by the appliance and are connected to the CAN ports:
CAN sensors, modules:
VT408 / Extension unit
VT430 / Rack control unit
VT440 / Dry contacts unit
VT460 / Smoke, humidity, and temperature...
VT470 / PIR, vibration and temperature sensor
VT490 / Humidity and temperature sensor
and other...
CAN extension unit:
VT408 / Extension unit
Used cable and limit line length
The maximum length of the CAN line in Vutlan monitoring systems is   due to limitations on the ohmic resistance of 225 m
cables with RJ12 connectors.
It is advisable to use two or three pairs of cables such as UTP Cat3.5.6 with 24AWG with a copper core. It is possible to use a 
4-wire or 6-wire TRONIC or UTP CCA cable, but the maximum CAN line length will be reduced.
Read more about   sensors.Setting up CAN

TR termination switch

pic.1.1: FR is OFF, TR is ON. pic.1.2: FR is OFF, TR is OFF.

Adding CAN modules and sensors

To connect the CAN module or CAN sensor to the CAN bus of the system, go to the interface >> CAN configuration panel >>

Select the CAN1 or CAN2 tab (select the connected physical CAN1 or CAN2 port on the master module).

Click the "Configure" button and wait. The system will start CAN bus polling, soon it will display the data lines and write

“Done!”. The modules and sensors connected to the CAN input will appear in a tab in the list. Click the Apply button and then

Restart.

The green LED " " of the device will light up.CAN status

The last sensor TR switch on a CAN chain must always be terminated, ( switched ON ). Sensors on a CAN bus that is

in the middle should have TR switched OFF.

FR should always be OFF.

TR switch is always the DP switch nearest to the CAN bus.

Only older Vutlan models have an FR switch.

Go to panel "System Tree" to see the new devices or new sensors. The article numbers for CAN devices are VT4xx. If they do

not appear, wait, or refresh.

LEDs

CAN sensors have LEDs that indicate the following states:

Red continuous light, green flickers - no communication with the master module

Red continuous light, green is off - there is a connection with the master unit, but is not included in the monitoring

system (not configured)

Red is off, Green continuously light - work as part of a monitoring system

All LEDs are off: no power or sensor is defective.

Maximum cable length test

Model Description 50m 100m 150m 200m

If after clicking the "Configure" button the poll is reset to the phrase "Update", then the line is not connected or the

terminators on the bus are not agreed. It is necessary to check and change the condition of the (See TR terminators

"TR termination switch" section above) on the modules or check and possibly change the .connection cables

Warning: If the bus is not matched, that is, there are bad contacts or bad cables, or the TR terminator is in the" " ON

position on the intermediate devices (position 2 on the VT408), or the line is too short for matching on both CAN end

devices, CAN on this line can work malfunctioning or the line as a whole may not function. (CAN line failure may occur

if the parallel CR switch is in state 1, must be in OFF).

VT408 Sensor extension unit ok

VT408DIN ok

VT430 Rack control unit ok

VT440 Dry contacts unit ok

VT460 Smoke, humidity, temperature ok

VT490 /

VT490i

Dual humidity and temperature sensor /

Pressure, humidity & temperature sensor

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung