Wabtec R-150 Bedienungsanleitung

Issued May 2022 (Rev C) Bulletin MI15RRD

Wabtec Components LLC

535 West 3rd Street, Berwick, Pa 18603

Tel: (570) 752-5901

Fax: (570) 752-6397

MODEL R-150

"CUSHION-RIDE" RAILGEAR

INSTALLATION MANUAL

"ROTATING FRONT - ROTATING REAR"

READ THIS MANUAL BEFORE

INSTALLING RAILGEAR EQUIPMENT

Application Models: 1999 - 2007 Dodge Dakota (All Models)

1999 - 2007 Dodge Durango (All Models)

2013 Ford Ranger XLT

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

Note:

The appendix of this manual includes the latest changes to the installation and operation

of the railgear not included in the “body” of this manual.

Please refer to the appendix prior to installing and operating the railgear.

The information in the appendix supersedes whatever is mentioned in the “body” of this

manual.

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

TABLE OF CONTENTS

Initial Preparation Section 1

Safety Precautions 1-2

Installation Procedure Overview 1-3

Preparations For Railgear Installation 1-4

Railgear Installation Section 2

Front Railgear Mounting Plate Installation 2-2

Front Railgear Installation 2-4

Rear Railgear Mounting Plate Installation 2-6

Rear Railgear Installation 2-10

Rail Wheel And Rail Sweep Installation 2-12

Front Railgear Bumper And Rail Sweep Arm Installation 2-14

Auxiliary Installations Section 3

Steering Wheel Lock Installation 3-2

Hydraulic System Installation 3-4

Electrical System Installation 3-7

Railgear Set-Up And Adjustments 3-10

Pre-Delivery Check List 3-13

Appendix Section 4

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

SECTION 1: INITIAL PREPARATION

SAFETY PRECAUTIONS 1-2

INSTALLATION PROCEDURE OVERVIEW 1-3

PREPARATIONS FOR RAILGEAR INSTALLATION 1-4

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

1.0 SAFETY PRECAUTIONS

WARNING:

 Refer to the Operating, Service and Parts manual for installation related

warranty issues.

 Installation instructions provided below only address the Rafna

Industries railgear equipment. Applicable railway company procedures

and policies must be adhered to.

 Always disconnect the vehicle’s battery when welding on the vehicle or

railgear in order to protect the vehicle’s electrical system.

 Before performing any work under the vehicle or railgear, ensure the

engine is turned off and the parking brake is set.

 Beware of all pinch points on the railgear and keep all parts of the body

clear.

 The following safety precautions should be taken before the vehicle is

tested or operated:

 Read the Operating, Service and Parts Manual

 Visually inspect the railgear for damaged or worn parts

 Perform the Alignment Procedure

 Check for loose wheels and fasteners

 Check for leaking hydraulic lines and cylinders

 Check for proper lubrication

Failure to heed to any of the above mentioned warnings could result in severe

bodily injury and/or equipment damage.

IF ANY INSTALLATION PROBLEMS ARE ENCOUNTERED, PLEASE CALL G&B

SPECIALTIES, INC. FOR TECHNICAL ASSISTANCE BEFORE CONTINUING WITH

THE INSTALLATION PROCESS.

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

2.0 INSTALLATION PROCEDURE OVERVIEW

This manual covers the installation of the Rafna Industries rotating front and rotating rear

R-150 railgear as applicable to multiple vehicles. If necessary, any difference in

installation for specific vehicle and/or railgear models is clearly detailed by separate

instructions for each. Otherwise the installation instructions are the same for all models.

Please refer to the appendix for the latest additions that have not been included in this

manual.

The Rafna Industries R-150 railgear is a hydraulically operated road-to-rail conversion

system applicable to vehicles of up to 6,500 lbs. gross vehicle weight rating (GVWR).

The front and rear railgear are frame mounted systems which are hydraulically raised and

lowered. The hydraulic power is supplied by a 12 VDC electrical / hydraulic pump.

The installation procedure consist of first installing the front and rear railgear. The

hydraulic and electrical installations follow and finally an adjustment of the equipment is

performed.

This manual uses the orientation convention for the vehicle as shown in figure 1-1.

FIGURE 1-1 : ORIENTATION CONVENTION

LEFT

RIGHT

FRONT REAR

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

3.0 PREPARATIONS FOR RAILGEAR INSTALLATION

The following steps must be performed on all vehicles prior to installation of the railgear

equipment:

1. Disconnect the negative battery terminal.

2. Remove the spare wheel from under the vehicle’s cargo box if so equipped. A new

location must be found for the spare wheel and the necessary brackets fabricated.

3. Remove the front bumper and all related mounting brackets. Retain all parts for re-

installation.

4. Remove the tail pipe section of the exhaust. Retain all parts for re-installation.

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

SECTION 2: RAILGEAR INSTALLATION

FRONT RAILGEAR MOUNTING PLATE INSTALLATION 2-2

FRONT RAILGEAR INSTALLATION 2-4

REAR RAILGEAR MOUNTING PLATE INSTALLATION 2-6

REAR RAILGEAR INSTALLATION 2-10

RAIL WHEEL AND RAIL SWEEP INSTALLATION 2-12

FRONT RAILGEAR BUMPER AND RAIL SWEEP ARM INSTALLATION 2-14

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

1.0 FRONT RAILGEAR MOUNTING PLATE INSTALLATION

This section covers the installation of the front railgear mounting plates. The hardware

required for this installation is listed in table 2-1.

Table 2

1: Front Railgear Mounting Hardware

Part Number Description Qty

1783

Front Frame Reinforcement Plate

1783

Front Frame Reinforcement Plate

1800D

Front Mounting Plate (Left Side)

1800P

Front Mounting Plate (Right Side)

½” UNC Gr. 8 Bolt x 2” Long

½” Gr. 8 Washer

½” UNC Gr. 8 Nylon Insert Lock Nut

The following procedure details the front mounting plate installation (refer to figure 2-1):

1. Position the front mounting plates (Item 1) around the frame rails (Item 2) as shown

so that they cradle the frame rails.

2. Position the original Dodge inner bumper brackets (Item 3) in their original position.

Slide the matching front frame reinforcement plates (Item 4) into the frame rails. The

three holes in the front frame reinforcement plate, in the frame, in the front mounting

plate and in the inner bumper bracket on each side should all align. Use six ½” x 2”

long bolts, twelve ½” washers, and six ½” nuts (Item 5) to fasten all parts in place.

3. Remove and discard the clip-on nuts from the original Dodge outer bumper brackets

(Item 6). Position the outer bumper brackets in their original position. Slide the

matching front frame reinforcement plates (Item 7) into the frame rails. The two

holes in the front frame reinforcement plate, in the frame rail, in the front mounting

plate and in the outer bumper bracket on each side should all align. Use four ½” x 2”

long bolts, eight ½” washers, and four ½” nuts (Item 8) to fasten all parts in place.

4. Ensure the front mounting plates are seated against the bottom of the frame and

aligned with each other. Torque all ½” fasteners to 100 ft-lbs.

5. Modify the front bumper as required so that it can be re-installed with the mounting

plates in place.

6. Re-install the front bumper using the original Dodge fasteners. Level the bumper and

torque the original fasteners to Dodge specifications.

G&B Specialties Inc. 535 West 3rd Street, Berwick, PA, USA Tel: 1-570-752-5901 Fax: (570) 752-639

Inhaltsverzeichnis

Andere Wabtec Hebesystem Handbücher

Wabtec

Wabtec Ricon S Series Bedienungsanleitung

Wabtec

Wabtec Ricon TITANIUM S Series Bedienungsanleitung

Wabtec

Wabtec Ricon S Series Bedienungsanleitung

Wabtec

Wabtec Ricon K Series Bedienungsanleitung

Wabtec

Wabtec Ricon S Series Bedienungsanleitung

Wabtec

Wabtec R-290 Bedienungsanleitung

Wabtec

Wabtec Ricon FoldOver FR2SS Series Bedienungsanleitung

Wabtec

Wabtec Ricon S Series Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung