WAC Lighting Accent 5011 Bedienungsanleitung
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MARCH 2, 2016 12:00 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
Accent
5011 / 5012
WARNING
IMPORTANT: NEVER attempt to do any work without shutting off the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the“OFF”position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch“OFF”the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction may invalidate the UL listing of this fixture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualifié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez
pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calificado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal
en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación UL esta lámpara.
This instruction apply to the model(s) below:
5011-27
5011-30
5012-30
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MARCH 2, 2016 12:00 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
Accent
5011 / 5012
Mounting Stake
Qty: 1pcs
Outdoor Rated Wire Nut
Qty: 2pcs
Hex Key
Qty: 1pcs
Adjustable Shroud
Qty: 1pc
MOUNTING ACCESSORIES
Step 1: Determining the location
1. Make sure your main power is off.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood.
Hammer till the bottom of the ring is flush with the ground.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the ring is flush with the ground.
Fill the rest of the hole with the removed soil and pack it tight
to secure the stake.
4. Screw the fixture onto the stake provided, leading the wire from
the fixture through the wire slot in the stake.
Step 2: Wiring the Fixture
5. Cut the power supply wire from the transformer at the location
of the fixture.
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches is separated.
7. Strip off ½ inch of the insulating material from each wire and
connect one to each of the wires from the fixture using the
outdoor rated direct burial wire nuts provided.
Note: To install multiple fixtures, also connect the power
supply wire of each additional fixture to the connection
described in 7 of the previous fixture.
Hammer
Wood
Mounting Stake
Soil
Transformer
To Next Fixture
Mounting Stake
Fixture Wires
Wire Slot
Accent Lighting Fixture
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MARCH 2, 2016 12:00 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
INSTALLATION INSTRUCTION
Accent
5011 / 5012
Step 3: Installing the Fixture
8. Screw the fixture onto the stake provided, leading the wire from
the fixture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench. Close the
trench by applying an inward force to both sides of the trench.
Note: For model 5012, wires MUST be buried at least 18”
below the ground per NEC.
10. Repeat steps for other fixtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the fixtures
light up.
Step 4: Aiming the Fixture
12. Tilting: Loosen the joint screw and adjust the head of the fixture
to the desired direction before retightening the screw.
13. Rotating: Loosen the mounting knob and rotate the fixture to
the desired position before retightening the knob.
Step 5: Dimming Adjustment:
14. Use a Phillips head screwdriver to adjust the dimming dial.
15. Rotate until the arrow on the dial is pointed at the desired
wattage. The wattage may be adjusted to the pre-existing tabs
or any value in between.
16. The lower the wattage, the dimmer the fixture will be.
17. Please refer to the yellow tag to determine the size of the
required transformer.
4W *6.5W
2W *3.5W
8W *10.5W
13W *13.5W
16W *14.5W
Model: 5011 Model: 5012
*Numbers not printed
on fixture
Joint Screw
Mounting
Knob
Tilting Rotating
Runs to
the next
fixture
Transformer
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MARCH 2, 2016 12:00 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
4
INSTALLATION INSTRUCTION
Accent
5011 / 5012
Step 6: Beam Angle Adjustment:
18. Note the four pre-determined beam angles on the beam angle
changing dial.
19. Use the provided Hex Key to sightly loosen the screw.
Do not remove screw from the fixture.
CAUTION: the set screw should either be inset or flushed with
the surface of the fixture. Do not extrude out and removed from
the fixture at all times. It should only be taken out for fixture
servicing. Consult factory for service instruction.
20. Rotate the dial until the arrow is aligned with the desired
beam angle. This beam angle may either be one of the
pre-determined ones or any number in between.
21. Tighten the set screw that is located on the beam angle dial to
lock the dial in place.
Step 7: Shroud Adjustment
22. Loosen the thumb screw on the shroud.
23. Rotate the shroud until it is in the desired position to properly
cut off glare.
24. Retighten the thumb screw to lock the shroud in place.
Beam Angle Dial
Hex Key
Shroud
Thumbscrew
10
25
40
60
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MARCH 2, 2016 12:00 PM
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
5
ACCESSORIES
I. Lens Accessory:
Frosted, red, blue, green and amber lens accessories are used to alter the
spectrum and distribution of the light coming out of the fixture.
Installation: Place the lens in between the fixture and the shroud.
Tighten the thumb screw on the shroud to secure the lens in place.
II. Surface Mount Accessory
The surface mount accessory is used to mount the fixture to a hard
surface like wood or cement or as alternative to the mounting stake.
Installation: Mount the accessory to a hard surface using No. 10 Philips
head screws that are at least half an inch long. If mounting on concrete
or something similar, first use a plastic anchor sized for No. 10 screws.
If mounting on a soft surface first attach the included spikes.
Create a route underneath the accessory for your wire to travel through.
Lead your wire through the created route and screw your fixture onto
the surface mount accessory.
III. Tree Mount Accessory:
The tree mount accessory is a way for fixtures to be mounted on
the trunk or a branch of a tree while minimizing damage to the tree.
Installation: Mark the screw hole locations at the point of installation.
Thread one hex nut onto the screw until it is stopped by the wood screw
portion. Use a wrench to screw the bolt into the tree until the
unthreaded portion of the bolt meets the surface of the tree.
(Do this for all three bolts.) Place the tree mount bracket onto the bolts
and secure it using additional hex nuts. Attach light fixture and lead wire
through the bracket. Place all wire nuts into the tree mount bracket.
IV. Extension Accessory
Using extension rods and rod joiners, fixtures can be mounted
away from a surface in any desired direction.
Rods come in 5 sizes: 4 inches, 8 inches, 12 inches, 18 inches, and
24 inches. These rods can be connected via either straight or
90 degree rod joiners.
Installation: Screw in a rod joiner into your mounting accessory.
Screw an extension rod to the other side of the rod joiner.
Continue to use rod joiners and extension rods until the fixture is
in the desired position.
Lens Accessory
No. 10 Tapping Screw
Surface Mount
Accessory
Removable Spike
Tree Mount BracketHexnutWood Screw Bolt
90° Rod Joiner Extension Rod
Rod Joiner
Mounting Accessory
Shroud
INSTALLATION INSTRUCTION
Accent
5011 / 5012
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere WAC Lighting Landschaftsbeleuchtung Handbücher
Beliebte Landschaftsbeleuchtung Handbücher anderer Marken
Cooper Lighting
Cooper Lighting MCGRAW-EDISON WBG Bedienungsanleitung
Cooper Lighting
Cooper Lighting Invue 42 - 175W Bedienungsanleitung
Saxby Lighting
Saxby Lighting Islay 68784 Handbuch
LIGMAN
LIGMAN EU-10016-3 Bedienungsanleitung
Cooper Lighting
Cooper Lighting McGraw-Edison ZD Credenza Bedienungsanleitung
LIGMAN
LIGMAN KI-60475 Bedienungsanleitung
Cooper Lighting
Cooper Lighting Generation CLB25MWW5C373 Bedienungsanleitung
Malibu Boats
Malibu Boats CL905K Bedienungsanleitung
LIGMAN
LIGMAN NYB-30161 Bedienungsanleitung
LIGMAN
LIGMAN SI-80021 Bedienungsanleitung
Volt
Volt 2-in-1 Tiki-Brass Torch Light Bedienungsanleitung
Malibu Boats
Malibu Boats CM110P Bedienungsanleitung