WAGO 750-502 Bedienungsanleitung

Fieldbus Independent

I/O Modules

2 DO AC/DC 230 V SSR, 0.3 A

750-509

Manual

Version 1.0.3

ii • General

WAGO-I/O-SYSTEM 750

I/O Modules

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the correctness and com-

pleteness of this documentation. However, as errors can never be fully ex-

cluded, we would appreciate any information or ideas at any time.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally trademark or patent protected.

Content • iii

WAGO-I/O-SYSTEM 750

I/O Modules

Content

1Important Comments ................................................................................. 4

1.1 Legal Principles........................................................................................4

1.1.1 Copyright............................................................................................. 4

1.1.2 Personnel Qualification .......................................................................4

1.1.3 Intended Use ........................................................................................4

1.2 Symbols....................................................................................................5

1.3 Number Notation......................................................................................5

1.4 Safety Notes .............................................................................................6

1.5 Scope ........................................................................................................6

2I/O Modules ................................................................................................. 7

2.1 Digital Output Module ............................................................................. 7

2.1.1 750-509 [2 DO AC/DC 230 V SSR, 0.3 A] ........................................7

2.1.1.1 View................................................................................................7

2.1.1.2 Description......................................................................................7

2.1.1.3 Display Elements ............................................................................8

2.1.1.4 Schematic Diagram.........................................................................9

2.1.1.5 Technical Data ................................................................................9

2.1.1.6 Process Image ...............................................................................10

2.1.2 Contact Protective Circuit for Relay Modules ..................................11

4 • Important Comments

Legal Principles

WAGO-I/O-SYSTEM 750

I/O Modules

1 Important Comments

To ensure fast installation and start-up of the units described in this manual,

we strongly recommend that the following information and explanations are

carefully read and abided by.

1.1 Legal Principles

1.1.1 Copyright

This manual is copyrighted, together with all figures and illustrations

contained therein. Any use of this manual which infringes the copyright

provisions stipulated herein, is not permitted. Reproduction, translation and

electronic and photo-technical archiving and amendments require the written

consent of WAGO Kontakttechnik GmbH & Co. KG. Non-observance will

entail the right of claims for damages.

WAGO Kontakttechnik GmbH & Co. KG reserves the right to perform

modifications allowed by technical progress. In case of grant of a patent or

legal protection of utility patents all rights are reserved by WAGO

Kontakttechnik GmbH & Co. KG. Products of other manufacturers are always

named without referring to patent rights. The existence of such rights can

therefore not be ruled out.

1.1.2 Personnel Qualification

The use of the product detailed in this manual is exclusively geared to

specialists having qualifications in PLC programming, electrical specialists or

persons instructed by electrical specialists who are also familiar with the valid

standards. WAGO Kontakttechnik GmbH & Co. KG declines all liability

resulting from improper action and damage to WAGO products and third party

products due to non-observance of the information contained in this manual.

1.1.3 Intended Use

For each individual application, the components supplied are to work with a

dedicated hardware and software configuration. Modifications are only

permitted within the framework of the possibilities documented in the

manuals. All other changes to the hardware and/or software and the non-

conforming use of the components entail the exclusion of liability on part of

WAGO Kontakttechnik GmbH & Co. KG.

Please direct any requirements pertaining to a modified and/or new hardware

or software configuration directly to WAGO Kontakttechnik GmbH & Co.

KG.

Important Comments • 5

Symbols

WAGO-I/O-SYSTEM 750

I/O Modules

1.2 Symbols

Danger

Always abide by this information to protect persons from injury.

Warning

Always abide by this information to prevent damage to the device.

Attention

Marginal conditions must always be observed to ensure smooth operation.

ESD (Electrostatic Discharge)

Warning of damage to the components by electrostatic discharge. Observe

the precautionary measure for handling components at risk.

Note

Routines or advice for efficient use of the device and software optimization.

More information

References on additional literature, manuals, data sheets and INTERNET

pages

1.3 Number Notation

Number Code Example Note

Decimal 100 normal notation

Hexadecimal 0x64 C notation

Binary '100'

'0110.0100'

Within ',

Nibble separated with dots

6 • Important Comments

Safety Notes

WAGO-I/O-SYSTEM 750

I/O Modules

1.4 Safety Notes

Warning

Switch off the system prior to working on bus modules!

In the event of deformed contacts, the module in question is to be replaced, as

its functionality can no longer be ensured on a long-term basis.

The components are not resistant against materials having seeping and

insulating properties. Belonging to this group of materials is: e.g. aerosols,

silicones, triglycerides (found in some hand creams).

If it cannot be ruled out that these materials appear in the component

environment, then additional measures are to be taken:

- installation of the components into an appropriate enclosure

- handling of the components only with clean tools and materials.

Attention

Cleaning of soiled contacts may only be done with ethyl alcohol and leather

cloths. Thereby, the ESD information is to be regarded.

Do not use any contact spray. The spray may impair the functioning of the

contact area.

The WAGO-I/O-SYSTEM 750 and its components are an open system. It

must only be assembled in housings, cabinets or in electrical operation

rooms. Access must only be given via a key or tool to authorized qualified

personnel.

The relevant valid and applicable standards and guidelines concerning the

installation of switch boxes are to be observed.

ESD (Electrostatic Discharge)

The modules are equipped with electronic components that may be destroyed

by electrostatic discharge. When handling the modules, ensure that the

environment (persons, workplace and packing) is well grounded. Avoid

touching conductive components, e.g. gold contacts.

1.5 Scope

This manual describes the Digital Output Module 750-509

2 DO AC/DC 230 V SSR, 0.3 A of the modular WAGO-I/O-SYSTEM 750.

Handling, assembly and start-up are described in the manual of the Fieldbus

Coupler. Therefore this documentation is valid only in the connection with the

appropriate manual.

750-509 [2 DO AC/DC 230 V SSR, 0.3 A] • 7

View

WAGO-I/O-SYSTEM 750

I/O Modules

2 I/O Modules

2.1 Digital Output Module

2.1.1 750-509 [2 DO AC/DC 230 V SSR, 0.3 A]

2-Channel Digital Output Module AC/DC 230 V

Solid State Relay 0.3 A

2.1.1.1 View

13 14

750-509

DO 2

Power jumper contacts

Data contacts

DO 2

230V

DO 1

Status

Fig. 2.1.1-1: 2-Channel Digital Output Module 750-509 g050900e

2.1.1.2 Description

The electronic relay module 750-509 can switch up to 230 V AC/DC, which

supplies actuators or AC loads.

The module has two output channels. Two actuators with ground (earth) wire

may be directly connected to signal output DO 1, N and PE (earth potential) or

signal output DO 2, N and PE.

The module is equipped with two high performance MOSFETs as switching

relays. The semiconductor outputs of the MOSFETs allow for the unlimited

triggering of the actuators while having no wear on the outputs.

The MOSFETs are non-floating, i.e. the fieldside voltage supply (0 V AC/DC

up to 230 V) is connected to each terminal of the relay and is fed in via the

internal power jumper contacts of an adjacent supply module.

By closing a relay, the field power applied is switched to the second relay

connection of signal output DO1 or DO2.

8 • 750-509 [2 DO AC/DC 230 V SSR, 0.3 A]

Display Elements

WAGO-I/O-SYSTEM 750

I/O Modules

The semiconductor outputs can be controlled fully isolated using the internal

system voltage.

The specified output values are designed for 100 % duty cycle.

The switching status of the two relays is indicated via green status LEDs.

Any configuration of the output modules is possible when designing the

fieldbus node. Grouping of module types is not necessary.

Attention

An additional supply module must be added for the field supply with

AC/DC 0 V to 230 V.

The AC/DC 0 V to 230 V supply voltage for the field side, the N (neutral

conductor) and the earth (ground) potential is made automatically through the

individual I/O modules by means of power jumper contacts.

Warning

The maximum current of the internal power jumper contacts is 10 A. When

configuring the system it is important not to exceed the maximum/sum

current. However, if such a case should occur, another supply module must

be added.

Note

For the protection of relay coils and contacts, inductive loads must be

dampened with an effective protection circuit!

Examples of protection circuits can be seen in the section 2.1.2 "Contact

Protective Circuit for Relay Modules".

The output module 750-509 can be used with all couplers/controllers of the

WAGO-I/O-SYSTEM 750.

2.1.1.3 Display Elements

LED Channel Designation State Function

off Output DO 1: not activated

green 1 Status

DO 1 on Output DO 1: activated

off Output DO 2: not activated

13 14

Fig. 2.1.1-2: Display

Elements g050102x

green 2 Status

DO 2 on Output DO 2: activated

750-509 [2 DO AC/DC 230 V SSR, 0.3 A] • 9

Schematic Diagram

WAGO-I/O-SYSTEM 750

I/O Modules

2.1.1.4 Schematic Diagram

DO 1 DO 2

AC/DC 230V

750-509

AC/DC 230V

Fig. 2.1.1-3: 2-Channel Digital Output Module 750-509 g050901e

2.1.1.5 Technical Data

Module Specific Data

Number of outputs 2

Current consumption (internal)max. 10 mA

Switching voltage AC/DC 0 V ... 230 V

Switching current 300 mA

Peak current 0.5 A (20 s); 1,5 A (0.1 s)

Switching rate max. 5 Hz (24 V 0,3 A DF=50 %)

0,5 Hz (230 V 0,3 A DF=50 %)

Pull-in time typ. 4,0 ms

Pull-in time max. 10 ms

Dropout time typ. 0.1 ms

Dropout time max. 3,0 ms

RON typ. 2.1 Ω

RON max. 3.2 Ω

Overvoltage protection AC 275 V (Varistor)

Isolation 1,5 kVeff. (System/Supply)

*2,5 kV rated surge voltage

overvoltage category III

Internal bit width 2 bit out

Dimensions (mm) W x H x L 12 x 64* x 100

* from upper edge of 35 DIN rail

Weight ca. 55 g

10 • 750-509 [2 DO AC/DC 230 V SSR, 0.3 A]

Process Image

WAGO-I/O-SYSTEM 750

I/O Modules

Standards and Regulations (cf. Chapter 2.2 of the Coupler/Controller Manual)

EMC-Immunity to interference (CE) acc. to EN 50082-2 (96)

EMC-Emission of interference (CE) acc. to EN 50081-1 (93)

EMC-Immunity to interference

(Ship building)

acc. to Germanischer Lloyd (97)

EMC-Emission of interference

(Ship building)

acc. to Germanischer Lloyd (97)

Approvals (cf. Chapter 2.2 of the Coupler/Controller Manual)

CULUS (UL508)

ABS (American Bureau of Shipping)

BV (Bureau Veritas)

DNV (Det Norske Veritas) Cl. B

GL (Germanischer Lloyd) Cat. A, B, C, D

KR (Korean Register of Shipping)

LR (Lloyd's Register) Env. 1, 2, 3, 4

NKK (Nippon Kaiji Kyokai)

RINA (Registro Italiano Navale)

CULUS (UL1604) Class I Div2 ABCD T4A

KEMA II 3 G EEx nC II C T4

Conformity Marking

More Information

Detailed references to the approvals are listed in the document "Overview

Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM

ELECTRONICC Tools and Docs (Item-No.: 0888-0412)

or in the internet under:

www.wago.com !Documentation !WAGO-I/O-SYSTEM 750 !

System Description

2.1.1.6 Process Image

The output bits control the state of the outputs.

Output bit B1 B0

Meaning controls DO 2

Channel 2

controls DO 1

Channel 1

Andere Handbücher für 750-502

Inhaltsverzeichnis

Andere WAGO Steuereinheit Handbücher

WAGO

WAGO 750-1405/040-000 Bedienungsanleitung

WAGO

WAGO 750-564 Bedienungsanleitung

WAGO

WAGO 750-427/040-000 Bedienungsanleitung

WAGO

WAGO 750-1416/040-000 Bedienungsanleitung

WAGO

WAGO SPEEDWAY 767 Series Bedienungsanleitung

WAGO

WAGO 751-5701 Bedienungsanleitung

WAGO

WAGO 750 Series Bedienungsanleitung

WAGO

WAGO 750-651 Bedienungsanleitung

WAGO

WAGO 750-508/040-000 Bedienungsanleitung

WAGO

WAGO 750-453/040-000 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung

WAGO

WAGO 750-451 Bedienungsanleitung

WAGO

WAGO 750-614/040-000 Bedienungsanleitung

WAGO

WAGO 750 Series Bedienungsanleitung

WAGO

WAGO 750-430/040-000 Bedienungsanleitung

WAGO

WAGO 767-1501 Bedienungsanleitung

WAGO

WAGO 750-450 Bedienungsanleitung

WAGO

WAGO 750-515 Bedienungsanleitung

WAGO

WAGO 750-469/040-000 Bedienungsanleitung

WAGO

WAGO 761-114 Bedienungsanleitung

WAGO

WAGO SPEEDWAY 767 Series Bedienungsanleitung

WAGO

WAGO 4FDI 24V PROFIsafe V2.0 Produkthandbuch

WAGO

WAGO WAGO-TO-PASS 761 Bedienungsanleitung

WAGO

WAGO 750-1605/040-000 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Flyron

Flyron FN-BC04 Bedienungsanleitung