WAREMA KNX SA 4MDC REG Bedienungsanleitung

Installation instructions

KNX SA 4MDC REG

Keep for future use!

Valid from 1st March 2017

2016158_0•en•2017_03_01 We reserve the right to make technical changes 1

WARNING

It is important to comply with the fol-

lowing points in the interest of personal

safety.

Children may not play with the operating elements of

the control unit or the remote control. Store remote

controls out of reach of children.

Make sure that no persons or objects are in the range

of movement of the driven parts (blinds, external vene-

tian blinds, etc.).

Disconnect the device from the supply voltage if

cleaning or other maintenance work must be perfor-

med.

Function of the sun shading actuator

You will find a detailed description of the software func-

tions for the KNX sun shading actuators in the manual

(art. no. 2014 788). You can download the manual and

the product database of the sun shading actuator from

www.warema.com.

Installation

The device is intended for installation in a distribution

cabinet. The device is mounted by clipping it onto a DIN

rail (TH 35/DIN 60715).

Electrical connection

An on-site overload current protection device (fuse) and a

disconnecting and isolating switch to switch off the entire

system must be provided.

The electrical connection is made as shown in the wiring

diagram on the reverse side (Fig. 4), the connection to

the KNX bus system and the drives is made using spring

terminals, the connecting lines are designed as screw

terminals.

General information

Fig. 1 KNXSA4MDC REG

The KNXSA4MDCREG sun shading actuator is a device

for the central operation of up to four sun shading drives

24 V DC.

The device is operated using a KNX bus system. The sun

shading actuator and the drives are supplied with 24 V

DC.

Intended use

The KNXSA4MDCREG was developed to control sun

shading products. The approval of the manufacturer

must be obtained for any use of the device other than its

intended purpose specified in these instructions.

The sun shading actuator is intended for installation in

enclosed electrical operating facilities.

Safety instructions

WARNING

The electrical installation must be per-

formed by a certiﬁed electrician in ac-

cordance with the electrical installation

regulations published by the Association

of German Electrical Engineers (VDE

0100) or the standards and legal require-

ments of the country in which the device

is being installed. The electrician must

observe the installation instructions inclu-

ded with the supplied electrical devices.

WARNING

If hazard-free operation cannot be assu-

med, the device may not be started or

must be deactivated. This assumption is

justiﬁed if:

 the housing or the connecting lines show

signs of damage,

 the device is no longer working.

2016158_0•en•2017_03_01We reserve the right to make technical changes

Commissioning

After the installation has been completed and the operat-

ing voltages have been applied, the device can be oper-

ated using a keypad (Fig. 2).

You will find a detailed description on the further commis-

sioning in the KNX manual (art. no. 2014 787).

Local operation

The keypad has 4 buttons, the Up / Down / Select and

Prog buttons, and an LED. The Select button is used to se-

lect the channel. The selected channel is displayed by one

of the 4channel LEDs. If the SEL button is pressed again

after selecting channel4, all channels are selected.

Fig. 2 Keypad

Local operation on the device has the same priority as

manual operation via communication objects. The operat-

ing behaviour is the same as the "KNX behaviour":

Brief push of the button = Step / Stop,

Long push of the button = Move.

WARNING

Never randomly press the buttons on the

keypad without having a line of sight to

the sun shading system.

Programming

Press the programming button (Fig. 2) to

put the device into programming mode. The

LED lights up red when programming mode

is active. The device is programmed on a

PC using the ETS. This software ends the

programming mode automatically. The red

LED goes out.

If the programming mode is to be ended

earlier, press the programming button again.

The red LED goes out.

Maintenance

There are no parts inside the device that require mainte-

nance. In the event of a malfunction, the built-in miniature

fuses should only be changed by a certified electrician.

Liability

Failure to comply with the product information in these in-

structions and any use of the device other than its intend-

ed use may result in the manufacturer refusing to honour

warranty claims for product damage. In this case, liability

for consequential damage to persons or property will also

be excluded. Observe the information in the operating

instructions for your sun shading system. The automatic

or manual operation of the sun shading system while iced

over as well as using the sun shading system during se-

vere weather may cause damage and must be prevented

by the user through suitable precautions.

Disposal

After use, the device must be disposed of according to

legal regulations or turned in to your local recycling centre.

2016158_0•en•2017_03_01 We reserve the right to make technical changes

Technical data

KNXSA4MDC REG min. typ. max. Unit

Operating voltage (SELV) 21.6 24 26.4 V DC

Current consumption in

standby mode

6.0 mA

Current consumption with

four activated relays

45 mA

Output per drive

Switching capacity per

channel at 24 V DC

20 72 W

Interface KNX TP 1

Current consumption KNX 3.5 13 mA

Voltage 29 V DC

Conformity

can be viewed at www.warema.com

This device complies with the EMC directives for use in

residential and commercial areas.

Ambient conditions

Operating temperature 0 50 °C

Storage temperature 0 70 °C

Humidity

(not condensing)

10 40 85 %Frel

Connection

Connecting line Screw terminals

KNX bus system, drives Spring terminals

Wire cross sections

Supply line

24 V DC

max. 2.5 mm²

KNX bus system 0.6 - 0.8 mm ∅

Motor outputs max. 1.5 mm²

Housing Degree of protection

DIN rail-mounted housing IP30

Safety class

(PE is looped through)

III

Miscellaneous

Automatic operation Type 1

Software class A

Location of use clean ambient conditions

Article numbers

KNXSA4MDC REG 2014 572

WAREMA Renkhoff SE

Hans-Wilhelm-Renkhoff Strasse 2

97828 Marktheidenfeld

Germany

60 mm

95 mm

90 mm

72 mm

4 MW

60 mm

Fig. 3 Dimensions of 4 MW DIN rail-mounted housing for

KNX SA 4MDC REG.

2016158_0•en•2017_03_01We reserve the right to make technical changes

24 V DC

24 V

0 V

+KNX Bus

KNX Bus -

All bus lines

JY(St)Y 4×2×0.8 mm

KNX-

KNX+

0V 24V

Supply line

24 V DC SELV

M1.1

M1.2

M2.1

M2.2

2,5 AT E

X1 X2

X5 X6

2,5 AT E

M3.1

M3.2

M4.1

M4.2

24 V DC

Motor 3Motor 4

2 x 0.75 mm²

Motor 1Motor 2

2 x 0.75 mm²

V+

Motor connection

Direction of movement

Mx.1 Mx.2

0 V

ATTENTION:

The operating voltage

must be SELV voltage

in accordance with

VDE 0700-1 or EN 60335-1.

NOTICE:

The fuse must be

adapted to the

respective drive.

Fig. 4 Connection example KNXSA4MDC 230 REG

Andere WAREMA Controller Handbücher

WAREMA

WAREMA LONMSE 6M230 Bedienungsanleitung

WAREMA

WAREMA KNX SA 16M230.32 SMI AP Bedienungsanleitung

WAREMA

WAREMA KNX SA 2M230 AP Series Bedienungsanleitung

WAREMA

WAREMA Omnexo 2M230 AP Bedienungsanleitung

WAREMA

WAREMA KNX MSE 6M230 Series Bedienungsanleitung

WAREMA

WAREMA KNX secure Series Bedienungsanleitung

WAREMA

WAREMA KNX SA 16M230.32 SMI AP Bedienungsanleitung

WAREMA

WAREMA KNX SA 2M230 REG Bedienungsanleitung

WAREMA

WAREMA LONMSE 2M230I Handbuch

WAREMA

WAREMA KNX SA 2M230 REG Bedienungsanleitung

WAREMA

WAREMA KNX 2024236 Bedienungsanleitung

WAREMA

WAREMA KNX SA 4MDC.8 AP Bedienungsanleitung

WAREMA

WAREMA Omnexo 1M230 UP Bedienungsanleitung

WAREMA

WAREMA 1MPF.4 UP Bedienungsanleitung

WAREMA

WAREMA KNX SA Series Bedienungsanleitung

WAREMA

WAREMA KNX SA 4MDC.8 AP Bedienungsanleitung

WAREMA

WAREMA 4M230.12 2Down REG Bedienungsanleitung

WAREMA

WAREMA KNX secure Series Bedienungsanleitung

WAREMA

WAREMA LONMPM 8DI Bedienungsanleitung

WAREMA

WAREMA Omnexo 2M230 REG Bedienungsanleitung

WAREMA

WAREMA LONMSE 2M230 Handbuch

WAREMA

WAREMA WMS SA 1 UP Bedienungsanleitung

WAREMA

WAREMA BACnet 4M230.8I AP Bedienungsanleitung

WAREMA

WAREMA KNX SA 16M230 SMI REG Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch