Waring MMB145 Bedienungsanleitung

MMB145 MMB150 MMB160

MMB Blender SerieS

inStruction Manual

Manual de inStruccioneS

para laS licuadoraS de la Serie MMB

directiveS d’utiliSation

deS BolS MixeurS de la Série MMB

For your safety and continued enjoyment of this product,

always read the instruction book carefully before using.

Para su seguridad y para disfrutar plenamente de este producto,

siempre lea las instrucciones cuidadosamente antes de usarlo.

An que votre appareil vous procure en toute sécurité beaucoup de

satisfaction, lisez toujours soigneusement les directives avant de l’utiliser.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions

should always be followed including the following:

1. READ ALL INSTRUCTIONS.

2. To protect against electrical hazards, do not immerse

the blender base in water or other liquids.

3. This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

4. Children should be supervised to ensure that they

do not play with the appliance.

5. Unplug from outlet when not in use, before putting

on or taking off parts, and before cleaning.

6. Avoid contact with moving parts.

7. Do not operate any appliance with a damaged cord or

plug or after the appliance malfunctions or is dropped

or damaged in any manner. Return appliance to the

nearest authorized service facility for examination,

repair or electrical or mechanical adjustment.

8. The use of attachments, including canning jars, not

recommended by the appliance manufacturer may

cause hazards.

9. Do not use outdoors.

10. Do not let cord hang over edge of table or counter,

where it can inadvertently be pulled on or tripped over

or touch hot surfaces, which could damage the cord.

11. Keep hands and utensils out of container while

blending, to prevent the possibility of severe personal

injury and /or damage to the blender. A rubber scraper

may be used, but must be used only when the blender

is not running.

12. Blades are SHARP. Handle carefully.

13. Never place cutting assembly or cutting blades on base

without container properly attached.

14. Always operate blender with cover in place.

15. Always operate blender with jar pad in place.

16. CAUTION: This blender is not intended for use with hot

liquids or ingredients.

17. Do not ll above MAX FILL line for blending.

18. Not for waterjet cleaning.

19. Ensure the jar coupler and motor coupler are aligned

and engaged before operating. If unable to engage,

remove jar and shake contents, then try again.

20. The jar coupler and motor coupler may be hot after

running; do no touch.

21. Replace jar pad if worn with groove.

22. Always use Hi speed for crushing ice.

23. If the jar overows during blending, there is too much

liquid/ingredients in the jar. Stop blending, remove

enough liquid/ingredients to below MAX Fill line, and

continue blending. Do not operate if overowing.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

• Foryourprotection,Waring®Commercial Blenders are

equipped with a 3-conductor cord set.

• 120voltunitsaresuppliedwithamolded3-prong

grounding-type plug and should be used in combination

with a properly connected grounding-type outlet, as

shown in Figure 1.

If a grounding-type outlet is not available, an adapter, shown

in Figure 2, may be obtained to enable a 2-slot wall outlet to

be used with a 3-prong plug.

Referring to Figure 3, the adapter must be grounded by

attaching its grounding lug under the screw of the outlet

cover plate.

CAUTION: Before using an adapter, it must be determined

that the outlet cover plate screw is properly grounded. If in

doubt, consult a licensed electrician.

Never use an adapter unless you are sure it is properly

grounded.

NOTE: Use of an adapter is not permitted in Canada.

BLENDER SPECIFICATIONS

•Capacity:48oz.WorkingCapacity

•Rating:120Volts,60Hz,13.0Amps

•BaseMaterial:Polycarbonate

•Bearing:High-PrecisionBallBearing

•Cord:6-FootThree-ConductorGroundCordwithStrain

Relief in Base

•OverallHeight:17Inches

•cETLus,NSFlisted

•OperatingCycle:1min.ON/3min.OFF

Controls:

MMB145 - Toggle Switches - Hi/Lo/Off and Pulse

MMB150 - Electronic Keypad - Hi, Lo, Stop, Pulse

MMB160 - Electronic Keypad with 60-Second Timer - Hi, Lo,

Stop, Pulse, Timer LED and Timer Up and Down Controls

MMB145 OPERATION

1. Before starting, make sure that the blender is

unplugged.

2. With the switch in Off

position, place container

on blender base. Be sure

container is fully seated

and that drive coupling is

properly engaged. Plug

blender cord into outlet.

GreenLEDlightwill

illuminate.

3. Put ingredients into container and cover it. Do not ll

above MAX FILL line.

4. This blender has 2 speed settings: Hi and Lo. Press

toggle switch to desired position. To crush ice, always

useHispeedsetting.GreenLEDlightwillblinkwhile

in operation.

NOTE: This blender utilizes a Slow Start™feature. When

beginning Hi or Lo operation, the unit will start in a lower

speed for 3 seconds and then switch to the full selected

speed. Pulse utilizes a 1-second Slow Start™. This allows for

a more even blending of ingredients in container.

5. When nished blending, set toggle switch to Off

position.

6. This blender is equipped with a Pulse option. Hold

toggle switch in down position to engage Pulse

function. Unit will run on Hi speed until the toggle

switch is released.

7. Allow motor to come to a complete stop before

removing container from blender base. Never place

the container on the motor base or remove it from

the motor base while motor is running.

8. Always hold container with one hand when starting and

while blending. Never operate without jar lid.

9. Wash and dry container after each use. See Cleaning

and Sanitizing Instructions.

10. Unplug to turn off all power to blender.

MMB150 OPERATION

Follow steps 1–3 above.

4. This blender is equipped

with an electronic membrane

keypad. The keypad has Hi,

Lo, Stop and Pulse buttons.

Always use Hi speed for

crushing ice.

5. For continuous operation, press either the Lo or Hi

button. When nished blending, press Stop. For

momentary operation, press the Pulse button; motor

willrunonHispeeduntilthebuttonisreleased.Green

LED light will blink while in operation.

NOTE: This blender utilizes a Slow Start™feature. When

beginning Hi or Lo operation, the unit will start in a lower

speed for 3 seconds and then switch to the full selected

speed. Pulse utilizes a 1-second Slow Start™. This allows for

a more even blending of ingredients in container.

6. Allow motor to come to a complete stop before

removing container from blender base. Never place

the container on the motor base or remove it from

the motor base while motor is running.

7. Always hold container with one hand when starting and

while blending. Never operate without jar lid.

8. Wash and dry container after each use. See Cleaning

and Sanitizing Instructions.

9. Unplug to turn off all power to blender.

MMB160 OPERATION

Follow steps 1–3 in the

MMB145 Operation section.

4. This blender is equipped

with an electronic membrane

keypad. The keypad has Hi,

Lo, Stop and Pulse buttons,

as well as a 60-second countdown timer with Up and

Down arrows to set time. Always use Hi speed for

crushing ice. The blender can operate in two modes:

timer mode and continuous mode.

5. For timer mode, press the Up or Down arrow to set the

desired time. The electronic timer will indicate run time

in 1-second intervals up to a maximum of 60 seconds.

Press and hold either Up or Down buttons for fast

scrolling. After the desired time is set, press Hi or Lo

tostarttheblender.GreenLEDlightwillblinkduring

blending. The timer will count down to 0 in 1-second

intervals and blender will shut off. Pressing the Pulse

button or the Stop button will override the timer and the

blender will stop regardless of time left on timer.

NOTE: If you want to increase or decrease time while timer is

counting down, press Up or Down arrows. Time will increase

or decrease in 1-second intervals.

6. If the Stop button is pressed, the timer function will

turn off and the unit will return to continuous mode. To

reactivate timer, press Up or Down arrows. When using

the electronic timer again, the initial time will be the last

time set. Note: If unit has been unplugged, the timer will

default back to 5 seconds.

7. For continuous operation, press either the Lo or Hi

button when timer is not lit. If the timer is lit and you

want to use continuous mode, press the Stop button

and proceed. When nished blending, press Stop. For

momentary operation, press the Pulse button. Motor

willrunonHispeeduntilthebuttonisreleased.Green

LED light will blink while in operation.

NOTE: This blender utilizes a Slow Start™feature. When

beginning Hi or Lo operation, the unit will start in a lower

speed for 3 seconds and then switch to the full selected

speed. Pulse utilizes a 1-second Slow Start™. This allows

for a more even blending of ingredients in container.

8. Allow motor to come to a complete stop before

removing container from blender base. Never place

the container on the motor base or remove it from

the motor base while motor is running.

9. Always hold container with one hand when starting and

while blending. Never operate without jar lid.

10. Wash and dry container after each use. See Cleaning

and Sanitizing Instructions.

11. Unplug to turn off all power to blender.

RESETTING THERMAL PROTECTION

• Yourblenderisequippedwithamanualresetswitchto

protect the motor from overheating.

• Ifyourblenderstopsrunningunderheavyuse,orifthe

GreenLEDlightstartstoblinkmuchmorerapidlythan

during normal blending, press the power switch to Off and

unplug the power cord. Empty the blender container of all

its contents and allow approximately 5 to 10 minutes for

the motor to cool down.

• Plugthepowercordbackintotheoutletandcontinue

blending.

• Ifyourblenderdoesnotfunctionproperlyfollowingthis

procedure, discontinue use and contact a certied Waring

Customer Service Center.

CLEANING AND SANITIZING INSTRUCTIONS

THE CONTAINER MUST BE CLEANED AND DRIED AFTER

EACHUSEOFTHEBLENDERACCORDINGTOTHE

FOLLOWINGINSTRUCTIONS.

FAILURETODOSOMAYALLOWRESIDUESOF

PROCESSED MATERIAL TO COLLECT ON THE INTERNAL

SEALSOFTHEBLADEASSEMBLY,RENDERINGTHEM

INEFFECTIVE.

• Wash,rinse,sanitizeanddrycontainerpriortoinitialuse

and whenever it will not be used again within a period of

1 hour.

• Washandrinsecontaineraftereachuse.

• Cleanandsanitizemotorbasepriortoinitialuseandafter

each use.

• Washingsolutionsbasedonnon-sudsingdetergentsand

chlorine-based sanitizing solutions having a minimum

chlorine concentration of 100 PPM are recommended.

The following washing, rinsing, and sanitizing solutions, or

their equivalents, may be used.

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE

Washing Diversey Wyandotte 4 Tablespoons Hot 115˚F ( 46˚C )

 DiversolBX/aorCX/A /Gallon

Rinsing Plain Water Warm 95˚F (35˚C)

Sanitizing Clorox® 1Tablespoon/Gallon Cold50–70˚F

Institutional Bleach ( 10–21˚C)

• Inrepetitivebatch-processingapplications,frequent

cleaning of the container will prolong the life of the blade

assembly. In no case should actual running time between

cleanings exceed one-half hour.

• Donotusecontainertostoreprocessedfoodsor

beverages.

TO WASH AND RINSE CONTAINER

1. REMOVE CONTAINER FROM MOTOR BASE.

Remove lid. Rinse container interior and lid under

running water. Add washing solution to container.

Scrub and ush out the container interior and lid to

dislodge and remove as much food residue as

possible. Empty container.

2. Wipe down exterior of container with a soft cloth or

sponge dampened with washing solution. Wash lid

and lid insert in fresh washing solution. Fill container

one-quarter full with fresh washing solution, cover

(with lid only), place on motor base and run on Hi speed

for two (2) minutes. Empty container.

3. Repeat step (2) using clean rinse water in place of

washing solution.

IMPORTANT

Note:INORDERTOMINIMIZEPOSSIBILITYOFSCALDING,

TEMPERATUREOFWASHINGSOLUTIONANDRINSE

WATERMUSTNOTEXCEED115˚F(46˚C),ANDQUANTITY

USED MUST NOT EXCEED ONE-QUARTER CONTAINER

FULL.

TO SANITIZE AND DRY CONTAINER

1. Wipe down exterior of container with a soft cloth

or sponge dampened with sanitizing solution.

2. Fill container with sanitizing solution, cover, place on

motor base, and run on Hi speed for one (1) minute.

Empty container. Dislodge any residual moisture from

blade assembly by placing empty container on motor

base and running on high speed for two (2) seconds.

3. Sanitize lid and lid insert by immersing in sanitizing

solution for two (2) minutes.

4. Do not rinse container, lid, or lid insert after sanitizing

is completed. Allow parts to air-dry.

TO CLEAN AND SANITIZE MOTOR BASE

 1. UNPLUGPOWERCORD.Wipedownexteriorsurfaces

of motor base with soft cloths or sponges dampened

with washing solution, rinse water, and sanitizing

solution. Prevent liquid from running into motor base

by wringing all excess moisture from cloths or sponges

before using them.

DONOTIMMERSEMOTORBASEINWASHINGSOLUTION,

RINSEWATERORSANITIZINGSOLUTION.

2. Allow motor base to air-dry before using.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Waring Mixer Handbücher

Waring

Waring 040072000829 Bedienungsanleitung

Waring

Waring WSB40 Bedienungsanleitung

Waring

Waring WSB Series Bedienungsanleitung

Waring

Waring PRO MX1000R Bedienungsanleitung

Waring

Waring Mx series Bedienungsanleitung

Waring

Waring MX1000XT Bedienungsanleitung

Waring

Waring 700G Bedienungsanleitung

Waring

Waring Mx series Bedienungsanleitung

Waring

Waring BB300 Bedienungsanleitung

Waring

Waring MBB1000 Series Bedienungsanleitung

Waring

Waring CB15T Bedienungsanleitung

Waring

Waring BB320 Bedienungsanleitung

Waring

Waring Quik Stik Plus WSB40ARG Bedienungsanleitung

Waring

Waring QUIK STIK PLUS WSB40 Bedienungsanleitung

Waring

Waring HGB140 Bedienungsanleitung

Waring

Waring NuBlend BB180PK Bedienungsanleitung

Waring

Waring Commercial Blender Bedienungsanleitung

Waring

Waring Blender Bedienungsanleitung

Waring

Waring MX1200XTX Bedienungsanleitung

Waring

Waring CB15 SERIES Bedienungsanleitung

Waring

Waring PRO MX1000R Bedienungsanleitung

Waring

Waring Ellipse MXE2000 Bedienungsanleitung

Waring

Waring BB185 Bedienungsanleitung

Waring

Waring EW-04242-11 Bedienungsanleitung

Beliebte Mixer Handbücher anderer Marken

ROTOR

ROTOR 1125.201 Bedienungsanleitung

Braun

Braun Multiquick 5 Vario series Bedienungsanleitung

ARENDO

ARENDO MIRA 305424 Bedienungsanleitung

CHEF-BUILT

CHEF-BUILT CCB-3500 Bedienungsanleitung

Viconte

Viconte VC-4406 Bedienungsanleitung

Oster

Oster BLSTAB-CB0 Bedienungsanleitung

HOFFEN

HOFFEN MC-3005 Bedienungsanleitung

Black & Decker

Black & Decker BLC18750DM Bedienungsanleitung

Sunbeam

Sunbeam 4182 Bedienungsanleitung

Bialetti

Bialetti FMX35 Bedienungsanleitung

Black & Decker

Black & Decker BL8000 Bedienungsanleitung

Duronic

Duronic BL530 Bedienungsanleitung

Exquisit

Exquisit MS 3002 wes Bedienungsanleitung

Lumme

Lumme LU-KP1891A Bedienungsanleitung

Binatone

Binatone HB-735 Bedienungsanleitung

Moulinex

Moulinex LM936E10 Bedienungsanleitung

Oster

Oster VERSA Installations- und Betriebshandbuch

Ninja

Ninja NN210Q Bedienungsanleitung