Warrior Winches 8000 Kurzanleitung

ELECTRICAL WINCH

8000 / 8000-SR

Assembly & Operating Instructions

INTRODUCTION

Congratulations on your purchase of a winch. We design and build winches to strict

specifications and with proper use and maintenance should bring you years of

satisfying service.

WARNING - Read, study and follow all instructions before operating this

device. Failure to heed these instructions may result in personal injury

and/or property damage.

Your winch can develop tremendous pulling forces and if used unsafely or

improperly could result in property damage, serious injury or death. Throughout

this manual you will find the following symbols for caution, warning and danger.

Pay particular attention to the notes preceded by these symbols as they are written

for your safety. Ultimately, safe operation of this device rests with you, the operator.

Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury. This notation is also used to alert against unsafe

practices.

Indicates a potentially hazardous situation which, if not avoided

could result in death or serious injury.

CAUTION

WARNING

GETTING TO KNOW YOUR WINCH

Your 8000lb winch is a powerful piece of machinery. It is important that you

understand the basics of its operation and specifications so that when you

need to use it, you can use it with confidence and safety. Below is a list of

the components of your winch and their use. Practices using your winch

before you are in a situation to need to use it.

1. Motor: Your 4.6hpmotor is powered by a 12 volt battery and providespower to the gear

mechanism which turns the drum and winds the wire rope;

2. Winch Drum: The winch drum is the cylinder on which the wire rope is stored. It can

feed or wind the rope depending on the remote winch switch.

3. Wire Rope: Your winch has a 21/64"X65.6' galvanized aircraft cable designed

specifically for load capacity of 8000lbs. The wire rope feeds onto the drum in the “under

wind” position through the roller fairlead and is looped at the end to accept the clevis

hook pin.

4. Roller Fairlead: When using the winch at an angle the roller fairlead acts to guide the

wire rope onto the drum and minimizes damage to the wire rope from abrasion on the

winch mount or bumper.

5. Mechanic Gear System: The reduction gears convert the winch motor power into

extreme pulling forces.

6. Braking System: Braking action is automatically applied to the winch drum when the

winch motor is stopped and there is a load on the wire rope. The braking action is

applied by a separate mechanical brake.

7. Free Spooling Clutch: The clutch allows the operator to manually disengage (“Out”) the

spooling drum from the gear train, free spool. Engaging the clutch (“In”) locks the winch

into the gear system.

8. Solenoid: Power from the vehicle battery flows through the weather sealed switch

before being directed to the winch motor.

9. Remote Switch: The Power switch lead has a dual switch for powering in or powering

out your winch drum. The Power switch leads allow you to stand clear of the wire rope

when the winch is under load.

10.Wireless Remote Control: allow you control winch far from 50 Ft away.

11.Universal Flat Bed Mounting Channel: Your winch has been optional

supplied with a flat bed mounting channel that can be mounted to most

flat surfaces such as trailers, stepbumpers, truck beds, etc. Themounting

channel also has holes to accept your roller fairlead.

12.Snatch Block: If Your winch were supplied with a snatch block that, used

properly, can double the pulling power of winch, or change your pulling

direction without damaging the wire rope. We recommend you to use

double line and snatch block for pulling over 85% related line pull.

WINCH ASSEMBLY AND MOUNTING

8000lbs:

1. Your 8000lb winch is designed with a bolt pattern that is standard in this class of

winch. Many winch mounting kits are available that utilize this bolt pattern for the

most popular vehicle and mounting channels. If you cannot find a kit locally,

utilize the mounting channel you must ensure that it is mounted on a flat surface

so that the three major sections (motor, drum and gear housing) are properly

aligned. Proper alignment of the winch will allow even distribution of the full rated

load.

2. Start by connecting the Roller Fairlead (Part# 800700) to the Mounting Channel

(Part# 800025) using 2 each of the Cap BoltM10 X 35 (Part# 800002), FlatWasher

(Part# 800004), Lock Washer (Part# 800003) and securing with M10 Nut(Part#

800024) (Make sure the bolt is placed through the mounting channel and roller

fairlead from inside the channel. This will allow enough clearance for the winch to

be placed in the channel without obstruction.)

3. Assemble the winch to the Mounting Channel (Part# 800025) by first pulling and

releasing the clutch knob to “Off” position (Free Spooling). Pull out a few inches

of cable from the drum and feed the wire loop through the opening in the front of

the mounting channel and roller fairlead. Now, using the remaining M10 x 35 Cap

Bolts (Part# 800002), Flat Washer (Part# 800004), Lock Washer (Part# 800003)

and M10 Nut (Part# 800005) secure the winch to the mounting channel.

4. Connect the battery and motor leads as the drawing above every type of winch is

different each other.

CAUTION –Batteries contain gases which are flammable and explosive.

Wear eye protection during installation and remove all jewelry. Do not lean over

battery while making connections.

5. Assemble the Clevis Hook to the cable. Take off the pin from the Clevis Hook,

connect the Clevis Hook to the cable and mount the pin back to the Clevis Hook.

6. Always use the Hand Saver when free-spooling and re-spooling the wire rope.

Using the Hand Saver keeps your hands and fingers away from the rotating drum.

7. Check for proper drum rotation. Pull and turn the clutch knob to the “off” position

(Free-spooling). Pull out some cable from the drum, and then turn the clutch knob

to the “In” position to engage the gears. Press the cable out button on the power

switch. If the drum is turning and releasing more cable then your connections are

accurate. If the drum is turning and collecting more cable then reverse the leads

on the motor. Repeat and check rotation.

SAFETY PRECAUTIONS

WARNING

WARNING –DO NOT EXCEED RATED CAPACITY.

WARNING –Intermittent use only.

WARNING - Do not use winch in lifting or moving or persons.

WARNING - A minimum of five wraps of cable around the drum

barrel is necessary for pulling and holding the rated load. The

cable clamp is not designed to hold the load without 5 wraps of

cable around the barrel.

WARNING - Keep yourself and others a safe distance to the side

of the cable when under tension.

WARNING –The wire rope may break before the motor stalls.

For heavy loads at or near rated capacity, use a pulley

block/snatch block to reduce the load on the wire rope.

WARNING -Never step over a cable, or near a cable under load.

WARNING - Don’t move the vehicle to pull a load (towing) on

the winch cable. This could result in cable breakage.

WARNING-Disconnect the remote control and battery leads

when not in use.

WARNING- Do not exceed maximum pull rating. Avoid “shock

loads” by using the control switch intermittently to take up the

slack in the wire rope. “Shock loads” can far exceed the rate

capacity for the wire rope and drum.

WARNING- Do not exceeds maximum line pull ratings shown on

the tables.

WARNING-When re-spooling the cable, ensure that the cable

spools in the under-wind position with the cable entering the

drum from the bottom, not the top. To re-spool correctly, and

while wearing gloves, keep a slight load on the cable while

pushing the remote button to draw in the cable. Walk toward the

winch not allowing the cable to slide through your hands. Do not

let your hands get within 12ąof the winch while respooling. Turn

off the winch and repeat the procedure until a few feet of cable

is left. Disconnect the remote control and finish spooling by

hand by rotating the drum by hand with the clutch disengaged.

Keep hands clear of the fairlead and drum while the winch is

under power.

Do not use as a hoist. Do not use for overhead lifting.

Failure to heed these warnings may result in personal injury

and/or property damage.

WARNING - Use gloves to protect hands when handling the

cable. Never let the cable slide through your hands.

WARNING –Never connect the cable back to itself.

Apply blocks to the wheels of the vehicle when on an incline. No

modifications, alterations, or deviation to the winch are

authorized by the manufacturer and SHALL not be made.

Duration of winching pulls should be kept as short as possible. If

the motor becomes uncomfortably hot to the touch, stop winching

immediately and let it cool down for a few minutes. Do not pull for

more than one minute at or near the rated load.

CAUTION - If the motor stalls do not maintain power to the

winch. Electric winches are designed and made of intermittent use

and should not be used in constant duty applications.

CAUTION - Never release the free-spool clutch when there is a load on the

winch.

CAUTION - Use hand saver hook when handling the hook for spooling or

un-spooling the wire rope.

GENERAL TIPS FOR SAFE OPERATION

xThe 8000lbs and its all derivative types are rated at 8000 lbs capacity

when spooling the first rope layer on the drum. Overloads can

damage the winch/motor/ or wire rope. For loads over 6800 lbs. we

recommend the use of the pulley block/snatch block to double the wire

rope line. The will aid in two ways: a) reduce the number or rope

layers on the drum, as well as, b) reduce the load on the wire rope by

as much as 50%. When doubling the line back to the vehicle, attach

to the frame or other load bearing part.

xThe vehicle engine should be kept running during operation of the winch

to minimize battery drain and maximize power and speed of the

winch. If the winch is used for a considerable time with the engine off

the battery may be drained and too weak to restart the engine

xGet to know your winch before you actually need to use it. We recommend

that you set up a few test runs to familiarize yourself with rigging

techniques, the sounds your winch makes under various loads, the

way the cable spools on the drum, etc.

xInspect the wire rope and equipment before each use. A frayed or

damaged rope shall be replaced immediately. Use only

manufacturer’s identical replacement rope with the exact

specifications.

xInspect the winch installation and bolts to ensure that all bolts are tight

before each operation.

xNever connect the cable back to itself. This will cause cable damage.

Always use a snatch block, sling or chain of suitable strength as

shown in the illustrations.

xStore the remote control inside your vehicle in a place that it will not be

damaged.

xAny winch that appears to be damaged in any way, is found to be worn,

or operates abnormally SHALL BE REMOVED FROM SERVICE

UNTIL REPAIRED. It is recommended that the necessary repairs be

made by a manufacturer’s authorized repair facility.

xPull only on areas of the vehicle as specified by the vehicle manufacturer.

xOnly attachments and/or adapters supplied by the manufacturer shall be

used.

RIGGING TECHNIQUES

Self Recovery

Locate a suitable anchor such as a strong tree trunk or boulder.

Always use a sling as an anchor point. CAUTION Do not attach

the clevis hook back onto the cable as this could cause damage to

the cable.

As shown in Fig 3.1

Do not winch from an acute angle as the wire rope will pile up

on one side of the drum causing damage to wire rope and the

winch. Fig 3.2

Short pulls from an angle can be used to straighten the vehicle.

Long pulls should be done with the wire rope at a 90° angle to

the winch/vehicle.

When pulling a heavy load, place a blanket or jacket over the

wire rope five or six feet from the hook. In the event of a broken

cable it will dampen the snap back. For additional protection

open the hood of the vehicle as shown in Fig 3.3

For pulls over 6800lbs, we recommend the use of the snatch

block/pulley block to double line the wire rope. Fig 3.4

This reduces the load on the winch and the strain on the rope by

approximately 50%.

Fig 3.1

Fig 3.2

Fig 3.3

Fig 3.4

WARNING - Never use your winch for overhead

hoisting or for lifting people or moving people.

WINCHING TECHNIQUES A-Z

a. Take time to asses your situation and plan your pull.

b. Put on gloves to protect your hands.

c. Disengage the clutch to allow free-spooling and also save battery power.

d. Attach the hand saver hook to the clevis hook.

e. Pull out the wire rope to your desired anchor point using the hand saver hook.

f. Secure the clevis hook to the anchor point: Sling, chain or snatch block. Do not attach

the hook back onto the wire rope.

g. Engage the clutch.

h. Connect the remote control to the winch.

i. Start your engine to ensure power is being replenished to the battery.

j. Power in the wire rope guiding the wire under tension to draw up the slack in the wire.

Once the wire is under tension stand well clear. Never step over the wire rope.

k. Double check your anchors and make sure all connections are secure.

l. Inspect the wire rope. Make sure there are at least 5 wraps of wire rope around the

winch drum.

m.Drape a blanket or jacket over the wire rope approximately 5 to 6 feet from the hook.

Open the hood for added protection.

n. Clear the area. Make sure all spectators all well back and that no one is directly in front

or behind the vehicle or anchor point.

o. Begin winching. Be sure that the wire rope is winding evenly and tightly around the

drum. The vehicle that is being winched can be slowly driven to add assistance to the

winching process. Avoid shock loads; keep the wire rope under tension.

p. The vehicle to be winched should be placed in neutral and the emergency brake

released. Only release the brake pedal when under full tension. Avoid shock loads to

the winch. This can damage the winch, rope and vehicle.

Fig 3.5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Warrior Winches Winde Handbücher

Warrior Winches

Warrior Winches Spartan Series Kurzanleitung

Warrior Winches

Warrior Winches 80RVSHY Bedienungsanleitung

Warrior Winches

Warrior Winches 80RVSHY Bedienungsanleitung

Warrior Winches

Warrior Winches S12000 Kurzanleitung

Warrior Winches

Warrior Winches 10JP0IH Bedienungsanleitung

Warrior Winches

Warrior Winches 6000EN Kurzanleitung

Warrior Winches

Warrior Winches 13JR02H-CAD Bedienungsanleitung

Warrior Winches

Warrior Winches S4000EN Kurzanleitung

Warrior Winches

Warrior Winches 10NHSHY Bedienungsanleitung

Warrior Winches

Warrior Winches 80SPS12 Kurzanleitung

Warrior Winches

Warrior Winches 20SPS12 Bedienungsanleitung

Warrior Winches

Warrior Winches T110S12 Bedienungsanleitung

Warrior Winches

Warrior Winches S8000 Kurzanleitung

Warrior Winches

Warrior Winches TROJAN 40PUS12 Bedienungsanleitung

Warrior Winches

Warrior Winches GLADIATOR 80FTA12 Bedienungsanleitung

Warrior Winches

Warrior Winches C10000NH Bedienungsanleitung

Warrior Winches

Warrior Winches SAMURAI 175SS12 Bedienungsanleitung

Warrior Winches

Warrior Winches 20YPSHY-CAD Bedienungsanleitung

Warrior Winches

Warrior Winches T1000 Bedienungsanleitung

Warrior Winches

Warrior Winches 10JP Bedienungsanleitung

Warrior Winches

Warrior Winches S2500EN Kurzanleitung

Warrior Winches

Warrior Winches 95SPS12 Kurzanleitung

Warrior Winches

Warrior Winches SAMURAI S17500-CAD Bedienungsanleitung

Warrior Winches

Warrior Winches NINJA 20SPS12-CAD Bedienungsanleitung

Beliebte Winde Handbücher anderer Marken

WARRIOR

WARRIOR Trojan 40PUS12 Kurzanleitung

SVERO

SVERO 16 Bedienungsanleitung

Badland Winches

Badland Winches 68146 Bedienungsanleitung

Bush

Bush II Series Bedienungsanleitung

Badland

Badland APEX 5500 Bedienungsanleitung

Quadratec

Quadratec Q9000 Synthetic Handbuch

C-Max

C-Max VIGO Bedienungsanleitung

Comeup

Comeup DV-9 Bedienungsanleitung

Orvea

Orvea Italwinch 805 Bedienungsanleitung

Prowinch

Prowinch PWJTHF300 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LD2000-A Bedienungsanleitung

Topex

Topex 97X080 Bedienungsanleitung

Eastbound

Eastbound MotoWinch 1707001 Bedienungsanleitung

Runva

Runva EWD8000 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Installationsanleitung

Granit

Granit 11157675 Bedienungsanleitung

TREX

TREX TB75 Bedienungsanleitung

Badland

Badland ZXR 2500 Bedienungsanleitung