Wassermann HSS-99 Bedienungsanleitung

Trimmer HSS-99 and HSS-88

Orthodontic Accessories

For Bite Orientated Trimming of Plaster Jaw Models

USER MA UAL

Dear customer,

Thank you for choosing a product from the Wassermann range. Wassermann Dental-

Maschinen incorporates the highest standards of quality and the latest technology.

In order to enjoy maximum performance and years of trouble-free operation, please read

this user manual carefully before you connect this device and start work, and operate the

device according to the recommended guidelines. The operation safety and the

functionality of this device can only be guaranteed if you follow both the general safety

guidelines and the applying laws to prevent accidents as well as the precautions given in

this user manual. We are not liable for any damages which occur due to inappropriate

usage or faulty operation of this device.

Make sure that anyone using this device has read and understood this user

manual.

Keep this user manual in a safe place where it can be referred to as required at

any time.

The unit complies with the relevant EU guidelines.

The unit is subject to the EU guidelines 2012/19/EU (WEEE Directive).

Company address:

Wassermann Dental-Maschinen GmbH

Rudorffweg 15-17

21031 Hamburg, Germany

Phone : +49 (0)40 730 926 -20/ -24 Fax.: +49 (0)40 730 37 24

[email protected]

www.wassermann.hamburg

Erstellt: 20.11.18/ msc Version: 1 164130 / 168140 / 164110 / 168120

Contents

1 Features.......................................................................................................................................4

1.1 Orthodontic Model Table.................................................................................................................4

1.1.1 Figure HSS-99 Model Table KMS according to Begg (Item no. 164130).......................................4

1.1.2 Figure HSS-88 Model Table KMS according to Begg (Item no. 168140).......................................4

1.2 Laser Light Guide for Orthodontic Model Table..............................................................................5

1.2.1 Figure HSS-99 Laser Light Guide for Model Table (Item no. 164110)...........................................5

1.2.2 Figure HSS-88 Laser Light Guide for Model Table (Item no. 168120)...........................................5

2 Safety Symbols used in this Manual.............................................................................................6

3 Safety Guidelines.........................................................................................................................6

4 Responsibility for Operation or Damage.......................................................................................7

5 Application....................................................................................................................................8

6 Before Starting............................................................................................................................. 9

6.1 Transport.........................................................................................................................................9

6.2 Storage............................................................................................................................................9

6.3 Installation of a Trimmer with Orthodontic Accessories Mounted...................................................9

7 Installation/ Start-up....................................................................................................................10

8 Operation................................................................................................................................... 10

8.1 General Operating Instructions.....................................................................................................10

8.2 Grinding Process...........................................................................................................................11

8.2.1 Important Advice Concerning the Usage of the Orthodontic Model Table....................................11

8.2.2 Usage of the Orthodontic Accessories.........................................................................................11

8.3 Adjustment of the Laser Light Guide.............................................................................................12

9 Troubleshooting.......................................................................................................................... 13

10 Care and Maintenance............................................................................................................. 13

10.1 Cleaning......................................................................................................................................13

10.1.1 Cleaning Instructions for the Orthodontic Model Table...............................................................14

10.2 Maintenance................................................................................................................................15

10.3 Repairs........................................................................................................................................15

10.4 Spare Parts.................................................................................................................................15

10.5 Service Hotline 0049 (0)40 730 926 -20/ -24..............................................................................15

10.6 Installation of Rep-Set LED (Item no. 164132)...........................................................................15

10.7 Installation of Rep-Set Laser (Item no. 164134).........................................................................15

10.8 Scope of Delivery/ Accessories...................................................................................................16

10.9 Warranty......................................................................................................................................16

11 Technical Data......................................................................................................................... 17

12 Disposing of the Unit................................................................................................................17

12.1 Information on Disposal for Countries within the EU..................................................................17

13 EU Declaration of Conformity...................................................................................................18

1 Features

1.1 Orthodontic Model Table

•All parts that come into contact with water are made of stainless steel.

•The seals are made of the latest generation of composite materials.

•The working surface with solid bearing is partially polished and has large slits to

allow the water to flow through to avoid the models sticking during grinding.

•The angle limit stop (Fig. page 8) is easily pivoted away.

1.1.1 Figure H -99 Model Table KM according to Begg (Item no. 164130)

1.1.2 Figure H -88 Model Table KM according to Begg (Item no. 168140)

1.2 Laser Light Guide for Orthodontic Model Table

•Laser class 1

•Combination of daylight LED and laser, precise and discreet, without glare or

reflections

•The user can adjust the guide light himself at any time.

•Due to the electrical connections, the installation of the guide light is performed by

our Wassermann Service or one of our licensed specialist companies.

1.2.1 Figure H -99 Laser Light Guide for Model Table (Item no. 164110)

1.2.2 Figure H -88 Laser Light Guide for Model Table (Item no. 168120)

2 afety ymbols used in this Manual

Warning!

This is a warning of risk situations and dangers.

Failure to observe this warning could be life-threatening. These warnings has to

be observed.

Information!

This symbol draws your attention to specific features that has to be observed.

3 afety Guidelines

Configuring and operating this equipment requires precise knowledge and observance

of the instructions in this user manual. The equipment is designed only for its intended

application.

WARNING:

Servicing and repairs should be carried out only by authorised specialists.

Disconnect the power plug before starting any maintenance work.

Make sure that the equipment is connected to the correct power source.

The user can adjust the laser light guide himself at any time. Due to the electrical

connections, the installation of the laser light guide is performed by our

Wassermann Service or one of our licensed specialist companies.

Laser class 1

•Please do not point the laser beam at people!

Even class 1 lasers should not be pointed at people, since the glare may

result in accidents.

•Do not look at the direct or reflected beam.

•Manipulations (modifications) to the laser equipment are not permitted.

•This operating manual should be kept carefully and handed over along

with the laser equipment.

4 Responsibility for Operation or Damage

The responsibility for operating the equipment lies exclusively with the owner or user if

said equipment is incorrectly serviced, maintained or altered by persons not employed by

an authorised dealer or if the equipment is used in a manner contrary to its specified

purpose.

The orthodontic accessories has to be maintained and operated in accordance with this

user manual. Wassermann Dental-Maschinen GmbH is not responsible for damage arising

from the nonobservance of these instructions.

Warranty and responsibility provisions contained in the sales and supply conditions of

Wassermann Dental-Maschinen GmbH are not extended by these instructions.

5 Application

Jaw models which are precisely prepared by the dental technician give the orthodontist the

basis for the necessary therapy. The requested task, a rational and accurate method of

producing plaster models is fully possible with the grinding equipment and the directional

lamp which belongs to it.

An exact line is projected on the grinding platform by the lamp. Exactly coordinated

combination of daylight-LED and laser ensure unparalleled sharp contours. The laser

beam is precise and not too hard at the same time.

Consequently, it is possible to exactly grind the tuber level of the upper jaw by aligning the

Raphe-Median-Line to the ghost line (Fig. 1).

The angle limit stop is pivoted away (Fig. 2).

Fig. 1

Fig. 2

Only use the accessories for this type of application.

The accessories for producing 3D orthodontic models are available for the trimmer

HSS-99 and HSS-88. Even subsequent upgrade is possible without any problems.

6 Before tarting

6.1 Transport

Before transporting the unit/laser light guide, ensure that it has been unplugged from the

power socket. Make sure that it is packed correctly in order to avoid accidental damage.

Be sure to check for any transport damage when unpacking the goods. ote down

any damage if found.

6.2 torage

The location is very important when it comes to workplace safety, even if it is only to be set

up there for a short period. The room should be dry, well ventilated and vibration-free. An

even temperature and wooden supports also help.

The unit/accessories should not be stored or set up outdoors.

If the unit/accessories is to be stored for an extended period, protect it from moisture and

dust.

6.3 Installation of a Trimmer with Orthodontic Accessories Mounted

ever use tray or illumination fitting for lifting out!

Open the box, remove the packing materials, and carefully lift out the device and

orthodontic accessories. Check the included accessories.

The device has to stand horizontally on a steady and even surface. Install

the device in a place where it will not block the working area and the functionality

(take the dimensions into account). When you set up the unit, make sure that the

grinding disc is accessible and that the unit is near a sink or close to the plaster

separator.

Do not install the unit and the accessories outdoors or in places without proper

ventilation. Before start-up, be sure the device reaches room temperature.

7 Installation/ tart-up

For further information please see the manual of your trimmer HSS-99 or HSS-88*.

Finally, insert the power plug into the socket, making sure that the mains and the

unit operate on the same voltage.

8 Operation

8.1 General Operating Instructions

All instructions for using the unit/ orthodontic accessories, whether in verbal or written

form, are based on our own experience and experimentation and can only be regarded as

guidelines.

A detailed description can be found in the application flyer* (included in delivery).

*If these instructions are not available, please do not hesitate to contact us.

A PDF file for download is available on our homepage:

www.wassermann.hamburg

Fig.: Flyer „HSS-99 and HSS-88 for Orthodontics .

Andere Handbücher für HSS-99

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wassermann Trimmer Handbücher

Wassermann

Wassermann HSS-ZA Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

GreenWorks

GreenWorks STA806 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung